Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
F2021-0197 - Misc
F2o21-Orr/ ES-A-C200_C200N ColtT"Series C200, C200N A M E S Double Check Valve Assemblies Sizes: 21/2" — 10" (65'— 250mm) LEAD FREE* Features • Extremely Compact Design • 70% Lighter than Traditional Designs • 304 (Schedule 40) Stainless Steel Housing & Sleeve • Groove Fittings Allow Integral Pipeline Adjustment • Patented Tri-Link Check Provides Lowest Pressure Loss • Unmatched Ease of Serviceability • Available with Grooved Butterfly Valve Shutoffs • Available for Horizontal, Vertical or N Pattern Installations • Replaceable Check Disc Rubber *The wetted surface of this product contacted by consumable water contains less than 0.25% of lead by weight. FIRE & WATERWORKS The Colt C200, C200N Double Check Valve Assemblies are used to prevent backflow of pollutants, that are objectionable but not toxic, from entering the potable water supply system. The Colt C200, C200N may be installed under continuous pressure service and may be subjected to backpressure. The Colt C200, C200N consists of two independently operating check valves, two shutoff valves, and four test cocks. For use in non -health hazard applications. The Colt C200, C200N features Lead Free* construction to comply with Lead Free` installation requirements. Specifications The Colt C200, C200N Double Check Valve Assembly shall consist of two independent Tri-Link Check modules within a single housing, sleeve access port, four test cocks and two drip tight shutoff valves. Tri-Link Checks shall be removable and serviceable, without the use of special tools. The housing shall be constructed of 304 (Schedule 40) stainless steel pipe with groove end connections. Tri-Link checks shall have reversible elastomer discs and in operation shall produce drip tight closure against the reverse flow of liquid caused by backpressure or backsiphonage. Lead Free* Double Check Valve Assembly shall be constructed using Lead Free` materials. It shall comply with state codes and standards, where applicable, requiring reduced lead content. Assembly shall be a Colt C200, C200N as manufactured by the Ames Company. ir4Stt �' LATj t� 1. {%?. 'r"� r` rCC�rS} ,r- ;] The information contained herein is`r3�t,{ ndeff"tofr 'Teethe full product installation and safety information availably pr the,� ie ce efa•trt i , ,i,r •. t installer. You are re- quired to thoroughly read all insfiall�tftatjo..: pr.�:Y.�si l ?rmation before beginning the ins allation of this product. IVI NOTICE ARVIVAMINVNIONOW ION Job Name Contractor Job Location �' Approva44 rt1fl Engineer Contractor NfO > o proposal iris; Represent Z1r c:;. to or plans Approval Represent�m]2�leCI )~p uetjon jnd field inspection+Cated Ames Fire & Waterworks product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Ames Fire & Waterworks Technical Service. Ames Fire & Waterworks reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Ames Fire & Waterworks products previously or subsequently sold. Configurations • Horizontal • Vertical up • "N" pattern horizontal Materials • Housing & Sleeve: 304 (Schedule 40) Stainless Steel • Elastomers: EPDM, Silicone and Buna 'N' • Tri-Link Checks: Noryl®, Stainless Steel • Check Discs: Reversible Silicone or EPDM • Test Cocks: Bronze Body Nickel Plated • Pins & Fasteners: 300 Series Stainless Steel • Springs: Stainless Steel Dimensions — Weights C200, C200N A (open) Available Models Suffix: NRS - non -rising stem resilient seated gate valves OSY - UVFM outside stem and yoke, resilient seated gate valves BFG - ULJFM grooved gear operated butterfly valves with tamper switch *OSY FxG - Flanged inlet gate connection and grooved outlet gate connection `OSY GxF - Grooved inlet gate connection and flanged outlet gate connection "OSY GxG - Grooved inlet gate connection and grooved outlet gate connection Available with grooved NRS gate valves - consult factory* Post indicator plate and operating nut available - consult factory* *Consult factory for dimensions Pressure — Temperature Temperature Range: 33°F - 140°F (0.5°C - 60°C) Maximum Working Pressure: 175psi (12.1 bar) SIZE (DN) in. mm A in. mm C (OSY) in. mm C (NRS) in. mm D in. mm G in. DIMENSIONS mm H in. mm in. I mm J in. mm in. P mm C200NRS lbs. kgs. WEIGHT C2000SY lbs. kgs. C200N NRS lbs. kgs. C200N OSY lbs. kgs. 2' 65 30% 781 163/6 416 9M 238 31/2 89 293/46 738 21' 546 151/2 393 8t3/46 223 93/6 234 115 52 125 57 123 56 133 60 3 80 313/4 806 18%/% 479 103/4 260 3' /6 94 30'A 768 223/4 565 171/2 435 93/6 233 10'/2 267 131 59 145 66 144 65 158 72 4 100 33% 857 223/4 578 123/6 310 4 102 33 838 23' 597 181/2 470 915/6 252 113/6 284 161 73 161 73 184 83 184 83 6 150 431/2 1105 301/6 765 16 406 51/2 140 443/4 1137 333/4 845 233/16 589 13'/6 332 15 381 273 124 295 134 314 142 336 152 8 200 49% 1264 373/4 959 1913/46 506 6"/6 170 541/31375 401/s 1019 277/6 697 15"/6 399 173/6 437 438 199 480 218 513 233 555 252 10 250 573/4 1467 453/1 1162 2313/6 605 83/6 208 66 1676 491/2 1257 321/2 826 175/6 440 20 508 721 327 781 354 891 404 951 431 C200BFG, C200NBFG SIZE (DN) in. mm in. A mm in. C mm in. D mm in. DIMENSIONS G mm in. H mm in. I min in. J mm in. P mm WEIGHT C200BFG lbs. kgs. C200NBFG lbs. kgs. 21/2 65 273/4 705 8 203 3'h 89 29% 759 211/2 546 1415/6 379 813/16 223 9 229 56 25 64 29 3 80 283/4 718 85/6 211 31/6 94 3011/6 779 22'A 565 157/16 392 93/46 233 9' 241 54 24 67 30 4 100 29 737 815/6 227 311/6 94 31t3/46 811 231/2 597 163/4 412 913/46 252 10 254 61 28 84 38 6 150 361/2 927 10 254 5 127 433/6 1097 33'A 845 19'1/6 500 133/46 332 101/2 267 117 53 157 71 8 200 42N 1086 12' 311 6' 165 513/46 1297 401/6 1019 235/6 592 151/6 399 143/6 361 261 118 337 153 Noryl® is a registered trademark of SABIC Innovative PlasticsTM. Approvals • Approved by the Foundation for Cross -Connection Control and Hydraulic Research at The University of Southern California (FCCCHR-USC) For additional approval information please contact the factory or visit our website at www.amesfirewater.com sg® US 1015 B64.5 psi 14 12 10 0 0 8 HE 6 ¢ • 4 2 0 0 Horizontal US Approved (**BFG & OSY Only) CenOmL•n ,.-/ANS: 61.0 Vertical N - Pattern 21/2" (65mm) Service Flow Rated Flow 'UL Rated Flow N H V 50 100 0 190 380 7.5 psi 12 10 O 8 1 J 8 00 6 4 • 2 0 0 0 Service Flow 150 200 250 570 760 950 15 3" (80mm) Rated Flow 300 350 gpm 1140 1330 Ipm fps 'UL Rated Flow H N V psi 24 2 20 a of 0 0 16 E, 12 U • 8 4 0 0 0 100 200 380 760 7.5 300 1140 15 4" (100mm) Service Flow Rated Flow 400 1520 500 gpm 1900 Ipm fps *IL Rated Flow N V H 100 200 300 400 500 600 700 800 gpm 380 760 1140 1520 1900 2280 2660 3040 Ipm 7.5 13 fps Capacity UL/FM Certified Flow Characteristics Flow characteristics collected using butterfly shutoff valves. Flow capacity chart identifies valve performance based upon rated water velocity up to 25fps • Service Flow is typically determined by a rated velocity of 7.5fps based upon schedule 40 pipe. • Rated Flow identifies maximum continuous duty perfor- mance determined by AWWA. • UL Flow Rate is 150% of Rated Flow and is not recom- mended for continuous duty. • AWWA Manual M22 [Appendix C] recommends that the maximum water velocity in services be not more than 10fps. Vl a o o (71 F psi 12 10 8 6 4 2 0 psi 12 10 8 6 4 2 0 6" (150mm) Service Flow Rated Flow 'UL Rated Flow N H V ! 0 0 300 600 1140 2280 7.5 900 1200 3420 4560 12 8" (200mm) Service Flow Rated Flow ! f jam`N. y— ` !- . .—.-� a" 1500 gpm 5700 Ipm fps •UL Rated Flow N H V 0 500 1000 1500 2000 ' 2500 gpm 0 1900 3800 5700 7600-.. 9500 Ipm 7.5 10 •` fps psi 12 0 - 10 a J o 0 0 8 E, 6 • 4 2 0 0 0 10" (250mm) Service Flow Rated Flow 'UL Rated Flow ice` N V H 500 1000 1500 2000 2500 3000 3500 gpm 1900 3800 5700 7600 9500 11400 13300 Ipm 7.5 . 10 fps NOTICE Inquire with governing authorities for local installation requirements MaIMa1eR R ROEMER Cerritos, California Union, New Jersey Atlanta, Georgia Wood Dale, Illinois ACTION EOUIPMENT Fire Protection Products Call Potter -Roemer for current listings and approvals. Dimensions are subject to manufacturers tolerance and change without notice. We assume no responsi- bility for use of superseded or void data. EXPOSED FIRE DEPT. INLET CONNECTIONS -CLAPPER TYPE TWO-WAY WITH SINGLE CLAPPER REGULARLY FURNISHED: Cast brass two-way inlet body, swing clapper and pin lug swivel. Back or angle outlet as selected by Figure Number. Lettering as selected. Size 4" x 21/2' x 21/2". I.-51"� ❑ Fig. 5710 ... Back Outlet U/L Usted FM Approved Fig. 5715 ... Angle Outlet U/L Usted FM Approved OPTIONAL FINISHES: ❑ - B Polished Brass ❑ - C Rough Chrome Plated ❑ - D Polished Chrome Plated LETTERING: AUTO. SPKR. 0 STANDPIPE THREADS: ❑ NST ❑ Other TWO-WAY WITH DOUBLE CLAPPERS REGULARLY FURNISHED: Cast brass two-way inlet body, drop clappers and pin lug swivels. Size and outlet as selected by Figure Number. Lettering as selected. ❑ Flg. 5720 Series Back Outlet ❑ FIg. 5730 Series 90° Angle Outlet 714" OPTIONAL FINISHES: ❑ - B Polished Brass ❑ - C Rough Chrome Plated ❑ - D Polished Chrome Plated LETTERING: . 0 AUTO. SPKR. ❑ STANDPIPE THREADS: ❑ NST ❑ Other ✓ Outlet Approvals ✓ Outlet Approvals Size A B C D Anale FIQ. No. Listed ® Appv'd Angle Fla. no. 0 Listed ® Appv'd 5721 Yes Yes 5731 Yes Yes 4 x 21/2 x 2'/2 71/2 111/2 81/2 11'/4 5722 No No 5732 No No 6 x 21/2 x 21/2 91/2 101/2 9 103/4 5723 No Yes 5733 No Yes 4x 3 x 3 91/2 111/2 91/2 11 5724 Yes No 5734 No No 6 x 3 x 3 10 11 10'/2 11 ALL DIMENSIONS IN INCHES REVISED 2-1-96 REVIEWED 1 2-1-96 MODEL NUMBER IV. FITTINGS Series 62: Strut Clamps Standard finish: electro-galvanized Cat. No. O.D. Tube Size Welght/C Gauge Allowable Load Slotted Indented Hex Cap Screw W-6224 1/4" 8# 16 400# 1/4 x 3/4 W-6225 3/8" 8# 16 400# 1/4 x 3/4 W-6226 1/2" 9# 16 400# 1/4 x 3/4 W-6227 5/8" 10# 16 400# 1/4 x 3/4 W-6228 3/4" 11# 16 400# 1/4 x 3/4 W-6229 7/8" 12# 16 400# 1/4 x 3/4 W-6230 1" 14# 14 600# 1/4 x 3/4 W-6231 1-1/8" 15# 14 600# 1/4 x 3/4 W-6232 1-1/4" 16# 14 600# 1/4 x 3/4 W-6233 1-3/8" 17# 14 600# 1/4 x 3/4 W-6234 1-1/2" 18# 14 600# 1/4 x 3/4 W-6235 1-5/8" 19# 14 600# 1/4 x 3/4 W-6034 1-3/4" 29# 12 800# 5/16 x 1 W-6237 1-7/8" 28# 12 800# 5/16 x 1 W-6238 2" 31# 12 800# 5/16 x 1 W-6239 2-1/8" 32# 12 800# 5/16 x 1 W-6240 2-1/4" 33# 12 800# 5/16 x 1 W-6138 2-3/8" 34# 12 800# 5/16 x 1 W-6242 2-1/2" 35# 12 800# 5/16 x 1 W-6243 2-5/8" 37# 12 800# 5/16 x 1 W-6244 2-3/4" 38# 12 800# 5/16 x 1 W-6142 2-7/8" 40# 12 800# 5/16 x 1 W-6246 3" 41# 12 800# 5/16 x 1 W-6247 3-1/8" 43# 12 800# 5/16 x 1 W-6248 3-1/4" 45# 12 800# 5/16 x 1 W-6249 3-3/8" 46# 12 800# 5/16 x 1 W-6146 3-1/2" 47# 12 800# 5/16 x 1 W-6251 3-5/8" 56# 11 1000# 3/8 x 1-1/4 W-6252 3-3/4" 58# 11 1000# 3/8 x 1-1/4 W-6253 3-7/8" 60# 11 1000# 3/8 x 1-1/4 W-6150 4" 62# 11 1000# 3/8 x 1-1/4 W-6255 4-1/8" 62# 11 1000# 3/8 x 1-1/4 W-6256 4-1/4" 64# 11 1000# 3/8 x 1-1/4 W-6257 4-3/8" 66# 11 1000# 3/8 x 1-1/4 W-6154 4-1/2" 67# 11 1000# 3/8 x 1-1/4 W-6259 4-5/8" 70# 11 1000# 3/8 x 1-1/4 W-6260 4-3/4" 72# 11 1000# 3/8 x 1-1/4 W-6261 4-7/8" 73# 11 1000# 3/8 x 1-1/4 W-6262 5" 74# 11 1000# 3/8 x 1-1/4 W-6263 5-1/8" 76# 11 1000# 3/8 x 1-1/4 W-6264 5-1/4" 77# 11 1000# 3/8 x 1-1/4 W-6265 5-3/8" 78# 11 1000# 3/8 x 1-1/4 W-6266 5-1/2" 79# 11 1000# 3/8 x 1-1/4 W-6267 5-5/8" 88# 10 1000# 3/8 x 1-1/4 W-6268 5-3/4" 90# 10 1000# 3/8 x 1-1/4 W-6269 5-7/8" 92# 10 1000# 3/8 x 1-1/4 W-6270 6" 94# 10 1000# 3/8 x 1-1/4 W-6274 8" 123# 10 1000# 3/8 x 1-1/4 W-6278 10" 106# 10 1000# 3/8 x 1-1/4 W-6282 12" 208# 10 1000# 3/8 x 1-1/4 Wesanco® Inc. W-6224/82 O.D. TUBING SERIES (Copper tubing, glass or ceramic tubes, and transite pipe) , t i / �f 1 ' Shown: 25% of actual ALLOWABLE LOAD (SAFETY FACTOR 5) SPECIAL MATERIALS PIPE CLAMPS For Series 60, Series 61, Series 62 (Universal Clamps excluded) Add Suffix to Material Part Number Example Steel Clamp Everdur Hardware -E W-6130-E Copper Plated Clamp and Hardware C/P W-6130 C/P Aluminum AL W-6130 AL Stainless Steel Type 304 ST-304 W-6130 ST-304 Stainless Steel Type 316 ST-316 W-6130 ST-316 For Assembled Clamps -A W-61 30-A © 2005 Wesanco Inc. All rights reserved. Westrut is the registered trade mark of Wesanco Inc., La Mirada, CA 90638 Hydra-Zorb is the registered trade mark o1 Hydra -Zarb Co., Auburn Hills, MI 48321-4400 Klo-Shure Is the registered trade mark of Klo-Shure Co., Royal Oak, MI 48068-0797 F62: 1 8/2005 For Design Data Ref. pages CH:1-3, CN:1-2, R:2-3, 6 and 7 BRACKETS & BRACE FITTINGS !R. 134 (30.2) FIG. 6123 - 6125 SHELF BRACKET 7Y4 (184.2) F(79.4) 3)6 734 (196.9) 0 -(19.1) Fig. B C Uniform Load Wt. Each No. lbs. kN lbs. kg 6123 161/2 (419.1) 6 (152.4) 1200 (5.34) 4.05 (1.84) 6124 181/2 (469.9) 6 (152.4) 1070 (4.76) 4.68 (2.12) 6125 201/2 (520.7) 6 (152.4) 600 (2.67) 4.90 (2.22) Note: Loads based on use with PHD 1000 series strut. 1345 (30.2) 5Y (133.4) 6125 6124 (79.4) 0 6123 (30.2) 136 (30.2) ii6 (30.2) FIG. 6130 - 6135 SINGLE CHANNEL BRACKET 2 (50.8) 3 4 76.2) (117.5) Fig. No. B Uniform Load Wt. Each lbs. kN lbs. kg 6130 6 (152.40) 1200 (5.34) 1.85 (.84) 6131 9 (228.60) 900 (4.00) 1.95 (.88) 6132 12 (304.80) 600 (2.67) 2.93 (1.33) 6133 14 (355.60) 500 (2.22) 3.20 (1.45) 6134 18 (457.20) 400 (1.78) 4.01 (1.82) 6135 24 (609.60) 300 (1.33) 5.09 (2.31) Note: Loads based on use with PHD 1000 series strut. FIG. 6140 - 6144 DOUBLE CHANNEL BRACKET 2 (50.8) Fig. No. B Uniform Load Wt. Each lbs. kN lbs. kg 6140 12 (304.80) 2000 (8.90) 5.05 (2.29) 6141 18 (457.20) 1300 (5.78) 7.10 (3.22) 6142 24 (609.60) 1000 (4.45) 9.15 (4.15) 6143 30 (762.00) 800 (3.56) 11.20 (5.08) 6144 36 (914.40) 650 (2.89) 13.25 (6.01) Note: Loads based on use with PHD 1000 series strut. Standard Product Information for 15/8" (41.3) width series channel fittings (Unless Otherwise Noted) Hole Diameter: V16" (14.3); Hole Spacing -From End:11/6" (20.6); Hole Spacing -On Center:17/8" (47.6); Width: 15/6" (41.3); Thickness: l/4" (6.4) Material: Carbon steel (Type 304 or 316 Stainless Steel upon request); Finish: Electro-galvanized (hot -dip galvanized, e-coat, and powder coated upon request) Ordering: Specify figure number, material, and finish. Unless otherwise specified, all dimensions on drawings and in charts are in inches and dimensions shown in parentheses are in millimeters. N 0 Uni-Flange® Adapter Flanges Series 200 Adapter Flange for Steel and Ductile Iron Pipe Flange Drilling ANSI B16.1 125 lb. / ANSI B16.5 150 Ib. WORKING PRESSURE - 2" THROUGH 8" 200 PSI / 10" THROUGH 12" 175 PSI .B44 ctx NOM PIPE SIZE STEEL PIPE DUCTILE IRON PIPE APPROX. INT.BOLT Lss. DIMENSIONS O.D. (INCHES) CATALOG NUMBER O.D. (INCHES) CATALOG NUMBER A B BC C HOLE DIA. SET SCREWS No. SIZE 2" 2.375 UFA200-S-2 2.50 UFA200-C-2 3.5 6" 1-13/16" 4-3/4" .75" 3/4" 2 1/2"x1" 2-1/2" 2.875 UFA200-S-25 - - 4.0 7" 1-13/16" 5-1/2" .75" 3/4" 4 1/2"x1" 3" 3.500 UFA200-S-3 3.96 UFA200-C-3 5.0 7-1/2" 1-13/16" 6" .75" 3/4" 4 1/2"x1" 4" 4.500 UFA200-S-4 4.80 UFA200-C-4 7.7 9" 1-7/8" 7-1/2" .75" 3/4" 4 1/2"x1" 5" 5.563 UFA200-S-5 - - 8.7 10" 1-7/8" 8-1/2" .75" 7/8" 8 1/2"x1" 6" 6.625 UFA200-S-6 6.90 UFA200-C-6 10.0 11" 1-7/8" 9-1/2" .75" 7/8" 8 1/2"x1" 8" 8.625 UFA200-S-8 9.05 UFA200-C-8 16.5 13 1/2" 2-1/4" 11-3/4" .88" 7/8" 8 5/8"x1-1/4" 10" 10.750 UFA200-S-10 11.10 UFA200-C-10 22.0 16" 2-1/4" 14-1/4" 1.00" 1" 12 5/8"x1-1/4" 12" 12.750 UFA200-S-12 13.20 UFA200-C-12 31.0 19" 2-1/4" 17" 1.00" 1" 12 5/8"x1-1/4" 4* is Series 400 Adapter Flange for Steel and Ductile Iron Pipe Flange Drilling ANSI 816.1 125 lb. / ANSI B16.5 150 lb. WORKING PRESSURE - 2" THROUGH 12" 250 PSI 14" THROUGH 24" 150 PSI / 30" THROUGH 48" 100 NOM. PIPE SIZE STEEL PIPE DUCTILE IRON PIPE APPROX LBs. DIMENSIONS A B BC C BOLT HOLE DIA.No. SET SCREWS O.D. (INCHES) CATALOG NUMBER O.D. (INCHES) CATALOG NUMBER SIZE 2" 2.375 UFA400-S-2 2.50 UFA400-C-2 5.0 6" 2" 4-3/4" 1.06" 3/4" 4 1/2"x1" 2-1/2" 2.875 UFA400-S-25 - - 7.0 7" 2-1/16" 5-1/2" 1.12" 3/4" 4 1/2"x1" 3" 3.500 UFA400-S-3 3.96 UFA400-C-3 8.0 7-1/2" 2-1/16" 6" 1.12" 3/4" 4 1/2"x1" 4" 4.500 UFA400-S-4 4.80 UFA400-C-4 11.0 9" 2-1/16" 7-1/2" 1.12" 3/4" 8 1/2"x1" 5" 5.563 UFA400-S-5 - - 13.0 10" 2-1/8" 8-1/2" 1.12" 7/8" 8 5/8"x1-1/4" 6" 6.625 UFA400-S-6 6.90 UFA400-C-6 14.0 11" 2-1/8" 9-1/2" 1.12" 7/8" 8 5/8"x1-1/4" 8" 8.625 UFA400-S-8 9.05 UFA400-C-8 21.0 13-1/2" 2-1/8" 11-3/4" 1.12" 7/8" 8 5/8"x1-1/4" 10" 10.750 UFA400-S-10 11.10 UFA400-C-10 38.0 16" 2-3/16" 14-1/4" 1.19" 1" 12 5/8"x1-1/4" 12" 12.750 UFA400-S-12 13.20 UFA400-C-12 56.0 19" 2-1/4" 17" 1.25" 1" 12 5/8"x1-1/4" 14" 14.000 UFA400-S-14 15.30 UFA400-C-14 70.0 21" 2-5/8" 18-3/4" 1.38" 1-1/8" 12 5/8"x1-1/4" 16" 16.000 UFA400-S-16 17.40 UFA400-C-16 79.0 23-1/2" 2-11/16" 21-1/4" 1.44" 1-1/8" 16 5/8"x1-1/4" 18" 18.000 UFA400-S-18 19.50 UFA400-C-18 90.0 25" 2-13/16" 22-3/4" 1.56" 1-1/4" 16 3/4"x2" 20" 20.000 UFA400-S-20 21.60 UFA400-C-20 145.0 27-1/2" 2-15/16" 25" 1.69" 1-1/4" 20 3/4"x2" 24" 24.000 UFA400-S-24 25.80 UFA400-C-24 175.0 32" 3-1/8" 29-1/2" 1.88" 1-3/8" 20 3/4"x2" 30" 30.000 UFA400-S-30 32.00 UFA400-C-30 270.0 38-3/4" 4" 36" 2.12" 1-3/8" 28 1"x2-1/4" 36" 36.000 UFA400-S-36 38.30 UFA400-C-36 400.0 46" 4-1/2" 42-3/4" 2.38" 1-5/8" 32 1"x2-1/4" 42" 42.000 1JFA400-S-42 44.50 UFA400-C-42 495.0 53" 4-3/4" 49-1/2" 2.63" 1-5/8" 36 1"x2-1/4" 48" 48.000 UFA400-S-48 50.80 UFA400-C-48 660.0 59-1/2" 4-7/8" 56" 2.75" 1-5/8" 44 1"x2-1/4" Options: To order with *Uni-Torque set screw add -UT to the catalog number. Example: UFA200-S-2-UT To order with *Uni-Torque set screws and EPDM gasket add -UT-EPDM to the catalog number. Example: UFA200-S-2-UT-EPDM To order with Stainless Steel set screws, sizes 2"-16", add -SS to the catalog number. Example UFA200-S-2-SS. * Caution: Uni-Torque set screws should not be used on steel pipe thinner than schedule 40 or ductile iron pipe thinner than class 52. U-8 FORD t Uni-Flange® Adapter Flanges Series 420 Extra Heavy Adapter Flanc for Steel and Ductile Iron Pipe Flange Drilling ANSI B16.1 250 Ib. / ANSI B16.5 300 Ib. (MATCHES CLASS F FLANGE) WORKING PRESSURE - 2" THROUGH 12" 400 PSI NOWSTEEL PIPE SIZE PIPE DUCTILE IRON PIPE APPROX WT. Las. DIMENSIONS A B BC C BOLT HOLE DIA. SET SCREWS O.D. (INCHES CATALOG NUMBER O.D. (INCHES) CATALOG NUMBER NO. SIZE 2" 2.375 UFA420-S-2 2.50 UFA420-C-2 7.0 6-1/2" 2-1/4" 5" 1.12" 3/4" 8 1/2" x 1" 3" 3.500 UFA420-S-3 3.96 UFA420-C-3 13.0 8-1/4" 2-7/16" 6-5/8" 1.12" 7/8" 8 1/2" x 1" 4" 4.500 UFA420-S-4 4.80 UFA420-C-4 21.0 10" 2-7/16" 7-7/8" 1.25" 7/8" 8 1/2" x 1" 5" 5.563 UFA420-S-5 - - 27.0 11" 2-9/16" 9-1/4" 1.38" 7/8" 8 5/8" x 1-1/4" 6" 6.625 UFA420-S-6 6.90 UFA420-C-6 38.0 12-1/2" 2-9/16" 10-5/8" 1.44" 7/8" 12 5/8" x 1-1/4" 8" 8.625 UFA420-S-8 9.05 UFA420-C-8 57.0 15" 2-5/8" 13" 1.62" 1" 12 5/8" x 1-1/4" 10" 10.750 UFA420-S-10 11.10 UFA420-C-10 74.0 17-1/2" 2-5/8" 15-1/4" 1.88" 1-1/8" 16 5/8" x 1-1/4" 12" 12.750 UFA420-S-12 13.20 UFA420-C-12 104.0 20-1/2" 3" 17-3/4" 2.00" 1-1/4" 16 5/8" x 1-1/4" Options: To order with *Uni-Torque set screw add -UT to the catalog number. Example: UFA200-S-2-UT To order with *Uni-Torque set screws and EPDM gasket add -UT-EPDM to the catalog number. Example: UFA200-S-2-UT-EPDM * Caution: Uni-Torque set screws should not be used on steel pipe thinner than schedule 40 or ductile iron pipe thinner than class 52. Optional Uni-Torque Set Screws Optional Uni-Torque Set Screws are available for use with Uni-Flange® Adapters, 2" through 16" nominal pipe sizes with the pipe thickness shown in the table below. These set screws feature a "break away head" that shears at the recommended torque, leaving a square head that can be used if future removal of the flange is required. To order an Adapter Flange with Uni-Torque set screws add "-UT" to the catalog number. Example: UFA200-S-2-UT. I UNI-TORQUE SET SCREW SIZE PRE-SET TORQUE VALUE *RECOMMENDED PIPE THICKNESS 1/2"x1" 65 ft-Ib t 7 Ductile Iron, Class 52-56 Steel, Schedule 40 and up 5/8"x2" 87 ft-Ib t 7 Ductile Iron, Class 52-56, Steel, Schedule 40 and up Note: 1/2" x 1" Uni-Torque Set Screws require a 3/8", 12 point, deep socket. 5/8" x 2" Uni-Torque Set Screws require a 7/16", 12 point, deep socket. * Caution: Uni-Torque set screws should not be used on steel pipe thinner than schedule 40 or ductile iron pipe thinner than class 52. FORD U-9 Recommended Set Screw Torque Values Series 200 / 400 / 420 Series 200 Adapter Flange I FLANGE SIZE i SET SCREW SIZE RECOMMENDED SET SCREW TORQUE VALUES (FT. LBS.) DUCTILE IRON PIPE (CLASS) STEEL PIPE (SCHEDULE) DUCTILE IRON PIPE (PRESSURE CLASS) 50 51 52 53+ 10 20 30 40+ 150 200 250 300 350 2" 1/2"x1" - - 70 70 30 - - 35 - - - - - 2-1/2" 1/2"x1" - - - - 30 - - 35 - - - - - 3" 1/2"x1" - 50 70 70 30 - - 70 - - - - 50 4" 1/2"x1" - 50 70 70 30 - - 70 - - - - 50 5" 1/2"x1" - - - - 30 - - 70 - - - -- 50 6" 1/2"x1" 50 60 70 70 30 - - 90 - - - - 50 8" 5/8"x1-1/4" 50 60 90 90 30 50 90 90 - - - - 50 10" 5/8"x1-1/4" 50 60 90 90 40 50 90 90 - - - - 50 12" 5/8"x1-1/4" 50 60 90 90 40 50 90 90 - - - - 50 Series 400 and 420 Adapter Flanges FLANGE SIZE SET SCREW SIZE RECOMMENDED SET SCREW TORQUE VALUES (FT. LBS.) DUCTILE IRON PIPE (CLASS) STEEL PIPE SCHEDULE) DUCTILE IRON PIPE (PRESSURE CLASS) 50 51 52 53+ 10 20 i 30 40+ 150 200 250 300. 350 2" 1/2"x1" - - 70 70 30 - - 35 - - - - - 2-1/2" 1/2"x1" - - - - 30 - - 35 - - - - - 3" 1/2"x1" - 50 70 70 30 - - 70 - - - - 50 3-1/2" 1/2"x1" - - - - 30 - - 70 - - - - 50 4" 1/2"x1" - 50 70 70 30 - - 70 - - - -- 50 5" 1/2"x1" - - - - 30 - - 70 - - - - 50 6" 5/8"x1-1/4" 50 60 80 80 30 - - 90 - - - - 50 8" 5/8"x1-1/4" 50 60 80 80 30 50 90 90 - - - - 50 10" 5/8"x1-1/4" 50 60 80 80 40 50 90 90 - - - - 50 12" 5/8"x1-1/4" 50 60 80 80 40 50 90 90 - - - - 50 14" 5/8"x1-1/4" 60 70 90 90 - 60 90 90 - - 50 50 60 16" 5/8"x1-1/4" 60 70 90 90 - 60 90 90 - - 50 60 60 18" 3/4"x2" 70 80 115 115 - 60 100 115 - - 60 70 70 20" 3/4"x2" 70 80 115 115 - 70 100 115 - - 70 70 70 24" 3/4"x2" 70 80 115 115 - 70 100 125 - 70 70 70 80 30" 1"x2-1/4" 90 110 125 125 - - - 125 70 80 90 110 125 36" 1"x2-1/4" 90 110 125 125 - - - 125 80 90 90 110 125 42" 1"x2-1/4" 90 110 125 125 - - - 125 90 90 90 110 125 48" 1"x2-1/4" 90 110 125 125 - - - - 90 90 110 110 125 Adapter Flanges are not suitable for use on spiral butt -welded steel pipe. U-10 FORD Deflection Chart Series 200 / 400 / 420 Uni-Flange® Adapters may be used to join flanged pipes and fittings that are slightly misaligned. They offer the following deflection capabilities, at full rated working pressure of the flange. Maximum angles of deflection may require an angular pipe cut to provide proper gasket compression. NoM. PIPE SIZE DUCTILE IRON PIPE O.D. (IN.) STEEL PIPE 0.D. (IN) MAXIMUM ANGLE DEFLECTION DEFLECTION I IN./18 FT. I LGTH. -(IN.) + 2" 2.50 2.375 4° - 2' 15.23 2-1/2" N/A 2.875 3° - 56' 14.85 3" 3.96 3.500 3° - 50' 14.47 3-1/2" N/A 4.000 3° - 47' 14.28 4" 4.80 4.500 3° - 44' 14.09 5" N/A 5.563 3° - 41' 13.91 6" 6.90 6.625 3° - 36' 13.59 8" 9.06 8.625 3° - 20' 12.58 10" 11.10 10.750 3° - 13' 12.14 12" 13.20 12.750 2° - 35' 9.12 14" 15.30 14.000 2° - 20' 8.80 16" 17.40 16.000 2° - 5' 7.86 18" 19.50 18.000 2° - 0' 7.54 20" 21.60 20.000 1 ° - 56' 7.29 24" 25.80 24.000 1 ° - 37' 6.10 30" 32.00 30.000 1 ° - 35' 5.97 36" 38.30 36.000 1 ° - 23' 5.22 42" 44.50 42.000 1 ° - 11' 4.46 48" 50.80 48.000 1 ° - 2' 3.89 Thrust Restraint The Uni-Flange® Adapter Series offers the following thrust restraint capabilities. NOM. PIPE SIZE SERIES 200 SERIES 400 SERIES 420 , WWP RATING (PSI) THRUST AT RATED PRESSURE (LBS.) WWP RATING (PSI) THRUST AT RATED PRESSURE (LBS.) WWP RATING (PSI) THRUST AT RATING PRESSURE ' (LBS.) 2" 200 892 250 1,115 400 1,784 3" 200 1,922 250 2,403 400 3,844 4" 200 3,181 250 3,975 400 6,360 6" 200 6,924 250 8,655 400 13,848 8" 200 11,724 250 14,655 400 23,448 10" 175 15,911 250 22,730 400 36,368 12" 175 22,375 250 31,965 400 51,144 14" - - 150 23,091 - - 16" - - 150 30,159 - - 18" - - 150 38,170 - - 20" - - 150 47,124 - - 24" - - 150 67,858 - - 30" - - 100 70,686 - - 36" - - 100 101,790 - - 42" - - 100 138,540 - - 48" - - 100 180,956 - - These values are calculated using steel pipe outside diameter dimensions. FORD U-11 TYLER UNION® Quality Waterworks Products SUBMITTAL 25U-Compact Mechanical Joint Tapping Sleeve for Ductile Iron, Cast Iron, & C900 PVC Pipe Revised 7/2013 (Current revisions for all Standards apply) SIZES: For 6"-12" PVC/ductile pipe per ANSI/AWWA C900 or C151 & Cast iron pipe O.D. as provided. Comes with 4"-12" side flanged outlet & 3/4" tap at branch. STANDARDS: Mechanical and *Flanged joints comply with applicable requirements of ANSI/AWWA C153 and ASME/ANSI B16.1. Cast with tested and traceable ASTM A536 ductile iron. Ductile iron Mechanical Joint Tapping Sleeves are produced in accordance with Tyler Union manufacturer's standard. are Dimension and specification ranges are per the standards as provided. Note: Recess dimensions are per Manufacturer's Standardization Society standard practice SP-60. Meets requirements of MSS SP-11 1 PRESSURE RATING:. 6"- 12" Assemblies rated @ 250 PSI. GASKETS: SBR Mechanical Joint and Split gaskets are per ASTM D2000 - AA and ANSI/AWWA C 11 1 /21.1 1, armor tipped with coiled brass wire spring. NSF-61 & NSF-372:Meets all requirements including Annex G ASPHALTIC COATING: ANSI/AWWA C104/A21.4 CEMENT LINING:Tapping Sleeves are unlined to ensure they fit over the pipe being tapped. FLANGE: ASME/ANSI B16.1, Class 125 FLANGE THICKNESS:ANSI/AWWA C153 and ASME B16.1 BOLTS: ANSI/AWWA C111/A21.11 DEFLECTION: Deflection is not recommended INSTALLATION: Per Tyler Union instructions as provided 1. Clean pipe, insert side gasket into back half of gasket grooves. Make sure ends are flush with or slightly protrude into the end gasket seating area. 2. Bolt sleeve halves together and trim side Size A B r- D 1 3//' TAPPED & PLUGGED FOR TESTING Dimensions C D E Pipe O.D. Range F Min. Max. DI gaskets as necessary. MAKE SURE 6x4 5.016 .250 7.50 15.75 8.00 12.75 6.85 7.15 104 SLEEVE WILL ROTATE FREELY ON PIPE. 6 7.016 .312 9.50 15.75 8.00 12.75 6.85 7.15 108 3. Install end gaskets, locating cut ends 90° 8x4 5.016 .250 7.50 16.50 9.00 13.375 9.00 9.35 134 from side gasket If pipe is maximum OD, 8x6 7.016 .312 9.50 16.50 9.00 13.375 9.00 9.35 140 stretch gasket to make certain cut ends 8 9.016 .312 11.75 16.50 9.00 13.375 9.00 9.35 148 match with no gap in between. 10x4 5.016 .250 7.50 24.00 11.00 20.75 11.04 11.45 236 4. Install glands and bolts -rotate sleeve to 10x6 7.016 .312 9.50 24.00 11.00 20.75 11.04 11.45 240 desired position. Be sure pipe is centered 10x8 9.016 .312 11.75 24.00 11.00 20.75 11.04 11.45 246 inside the sleeve. 10 11.016 .312 14.25 24.00 11.00 20.75 11.04 11.45 257 5. Tighten gland bolts alternately, using 80 to 12x4 5.016 .250 7.50 26.50 12.00 23.25 13.14 13.56 273 90 foot pounds. 12x6 7.016 .312 9.50 26.50 12.00 23.25 13.14 13.56 286 6. After assembly, PRESSURE TEST ALL 12x8 9.016 .312 11.75 26.50 12.00 23.25 13.14 13.56 292 JOINTS BEFORE TAPPING. If additional 12x10 11.016 .312 14.25 26.50 12.00 23.25 13.14 13.56 303 tightening is required, release pressure and 12 13.016 .312 17.00 26.50 12.00 23.25 13.14 13.56 320 relax tension on gland bolts before tighten- ing side bolts. Tyler:11910 CR 492-Tyler, TX 75706-(800) 527-8478 Anniston: 1501 W. 17th.-St. Anniston, AL 36201-(800) 226-7601 Corona: 1001 El camino Ave. -Corona, CA 92879-(866) 527-8471 Portland: 6204 N. Marine Dr. -Portland, OR 97203-(866) 527-8471 www.tvlpruninn.rnm 1.Q tqco I Fire &Building Products Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500 www.tyco-fire.com Grinnell Grooved Fire Protection Products Figure 577 Rigid Coupling - Patented General Description LPCB VdS See Fire Protection Submittal Sheet for Pressure Rating and Listing/Approval Information The Figure 577 Rigid Coupling pro- vides a rigid joint by firmly gripping along the circumference of the pipe grooves. Rigid couplings are preferred for dry pipe and freezer applications. Figure 577 Rigid Couplings are a proven dependable method of joining pipe and are an economical alternative to welding, threading, or using flanges. It is capable of pressures up to 300 psig (2069 kPa) depending on pipe size and wall thickness when used in fire protection services. Rigid Couplings are recommended for dry pipe and freezer applica- tions. WARNING The Figure 577 Rigid Coupling de- scribed herein must be installed and maintained in compliance with this document, in addition to the standards of any other authorities having jurisdic- tion. Failure to do so may impair the integrity of this device. The owner is responsible for maintain- ing their system and devices in proper operating condition. The installing contractor or manufacturer should be contacted with any questions. Technical Data Figure: 577 Sizes: 1-1/4" - 8" Approvals: UL, FM, ULC, VdS, and LPCB; See Fire Protection Submittal Sheet for exact Listing/Approval in- formation. Housing: Ductile iron conforming to ASTM A-536, Grade 65-45-12. Protective Coatings: • Non -lead orange paint. • Fire brigade red (optional) non -lead paint. • Hot dipped galvanized conforming to ASTM A-153. Bolts/Nuts: Track Head Bolts - con- forming to ASTM A-183, Inc Plated, (Min. Tensile = 110,000 psi/758,422 kPa). Metric - conforming to ASTM F568M. Gasket: • Prelubricated Grade "A" EPDMA violet color code ambient to +150°F (+66°C) for fire protection systems. Not recommended for hot water sys- tems. • Tri-seal (Grade "E" EPDM), green color code for use in dry pipe or freezer system. (See Data Sheet TFP1865 for aid in selecting proper gasket) Ordering Information When placing an order, indicate the full product name. Please specify the quantity, figure number, type of gas- ket, Grade "A" EPDMA, Prelubricated (Grade "A" EPDMA) or Grade "E" EPDM Tri-Seal, and size. Grinnell Grooved Piping Products, valves, accessories, and other prod- ucts are available throughout the U.S., Canada, and internationally, through a network of distribution centers. You may write directly or call 215-362-0700 for the distributor nearest you. Care and Maintenance The owner is responsible for the in- spection, testing, and maintenance of their fire protection system and de- vices in compliance with this docu- ment, as well as with the applicable standards of the National Fire Protec- tion Association (e.g., NFPA 25), in addition to the standards of any authority having jurisdiction. The in- stalling contractor or sprinkler manu- facturer should be contacted relative to any questions. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service in accordance with local requirements and/or national codes. Limited Warranty Products manufactured by Tyco Fire & Building Products are warranted solely to the original Buyer for ten (10) years against defects in material and work- manship when paid for and properly installed and maintained under normal use and service. This warranty will ex- pire ten (10) years from date of ship- ment by Tyco Fire & Building Products. No warranty is given for products or components manufactured by compa- nies not affiliated by ownership with Tyco Fire & Building Products or for products and components which have been subject to misuse, improper in- stallation, corrosion, or which have not been installed, maintained, modified or repaired in accordance with applica- ble Standards of the the standards of any other Authorities Having Jurisdic- tion. Materials found by Tyco Fire & Building Products to be defective shall be either repaired or replaced, at Tyco Fire & Building Products' sole option. Tyco Fire & Building Products neither Page 1 of 2 JULY, 2005 TFP1854 Page 2 of 2 TFP1854 assumes, nor authorizes any person to assume for it, any other obligation in connection with the sale of products or parts of products. Tyco Fire & Building Products shall not be responsible for sprinkler system design errors or inac- curate or incomplete information sup- plied by Buyer or Buyer's repre- sentatives. IN NO EVENT SHALL TYCO FIRE & BUILDING PRODUCTS BE LIABLE, Figure 577 Grooved Coupling IN CONTRACT, TORT, STRICT LI- ABILITY OR UNDER ANY OTHER LE- GAL THEORY, FOR INCIDENTAL, INDIRECT, SPECIAL OR CONSE- QUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR CHARGES, REGARDLESS OF WHETHER TYCO FIRE & BUILDING PRODUCTS WAS INFORMED ABOUT THE POSSIBILITY OF SUCH DAMAGES, AND IN NO EVENT SHALL TYCO FIRE & BUILDING PRODUCTS' LIABILITY EXCEED AN AMOUNT EQUAL TO THE SALES PRICE. THE FOREGOING WARRANTY IS MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED. INCLUDING WARRAN- TIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR- POSE. Pipe Max." $ End Gap Inches mm Max. t Pressure psi kPa Max. t End Load Lbs. N Nominal Dimensions Bolt Size•, Dia. x Lg. Net Weight Lbs. Kg Size O.D. Inches mm A Inches mm B Inches mm C Inches mm 1 1/4" 1.660 42.4 0.06 1.5 300 2,068 649 2,888 2.68 68 4.21 107 1.65 42 3/8" x 2 1/4" M 10 x 57 1.3 0.6 1 1/2" 1.900 48.3 0.06 1.5 300 2,068 851 3,783 2.91 74 4.45 113 1.65 42 3/8" x 2 1/4" M 10 x 57 1.5 0.7 2" 2.375 0.06 300 1329 3.39 5.00 1.69 3/8" x 2 1/4" 1.8 60.3 1.5 2,068 5,912 86 127 43 M 10 x 57 0.8 2 1/2" 2.875 73.0 0.06 1.5 300 2,068 1947 8,663 3.90 99 5.43 138 1.77 45 3/8" x 2 1/4" M 10 x 57 2.0 0.9 76.1 mm 3.000 76.1 0.06 1.5 300 2,068 2121 9,433 3.98 101 5.59 142 1.77 45 3/8" x 2 1/4" M 10 x 57 2.0 0.9 3„ 3.500 0.06 300 2886 4.49 6.14 1.77 3/8" x 2 1/4'' 3.3 88.9 1.5 2,068 12,839 114 156 45 M 10 x 57 1.5 4„ 4.500 0.19 300 4771 5.71 7.52 1.85 3/8" x 2 1/4" 3.3 114.3 4.8 2,068 21,223 145 191 47 M10 x 57 1.5 139.7 mm 5.500 139.7 0.19 4.8 300 2,068 7127 31,704 6.81 173 8.74 222 1.93 49 1/2" x 3" M12 x 76 5.3 2.4 5„ 5.563 0.19 300 7291 6.85 8.82 1.93 1/2" x 3" 5.3 141.3 4.8 2,068 32,434 174 224 49 M12 x 76 2.4 165.1 mm 6.500 165.1 0.19 4.8 300 2,068 9955 44,280 7.80 198 9.76 248 1.93 49 1/2" x 3" M12 x 76 5.7 2.6 6" 6.625 0.19 300 10341 7.91 9.88 1.93 1/2" x 3" 5.9 168.3 4.8 2,068 46,000 201 251 49 M12 x 76 2.7 8" 8.625 0.19 300 17527 10.24 12.80 2.40 5/8" x 3 1/4" 11.7 219.1 4.8 2,068 77,966 260 325 61 M16 x 83 5.3 Maximum available gap between pipe ends. Minimum gap = 0. t Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ on other pipe materials and/or wall thickness. Contact Tyco Fire & Building Products for details. See Fire Protection Equipment Submittal Sheet for Listing and Approval pressure ratings. Gold color coded metric bolt sizes are available upon request. Max. End Gap is for cut grooved standard weight pipe. Valves for roll grooved pipe will be 1/2 that of cut grooved. Figure 577 Rigid Couplings have an Anti -Rotation Feature of "gripping teeth" along the coupling keys, which make the Figure 577 perfectly suited for "arm over" installations where the likelihood of rotation is greatest. This feature may eliminate the need of extra hangers to support the arm over due to increased rigidity and gripping force saving time and cost. General Notes: It is the Designer's responsibility to select products suitable for the intended service and to ensure that pressure ratings and performance data is not exceeded. Always read and understand the installation instructions (IH-1000). Never remove any piping component or correct or modify any piping deficiencies without first depressurizing and draining the system. Material and gasket selection should be verified to be compatible for the specific application. Certified Company TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 two IFire &Budding Products Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500 www.tyco-fire.com Grinnell Grooved Fire Protection Products Grooved Fittings General Description LPCB, VdS See Fire Protection Submittal Sheet for Pressure Rating and Listing/Approval Information The grooved fittings provide an economical and efficient method of changing direction, adding an outlet, reducing, or capping grooved piping systems. Grooved fittings are available in durable ductile iron or fabricated steel as indicated. Note: Figure 510S and 519S fittings are special short radius fittings with smaller center to end dimensions than standard grooved fittings. Depending on the size and coupling used, there may be interferences at the bolt pads that require repositioning of the coupling orientation. The use of flange adapters is not recommended with Figures 510S and 519S fittings. Contact Tyco Fire Products for details. WARNING The Fittings described herein must be installed and maintained in compliance with this document, as well as with the applicable standards of the National Fire Protection Association, in addition to the standards of any other authorities having jurisdiction. Failure to do so may impair the performance of this device. The owner is responsible for maintaining their fire protection system and devices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Technical Data Approvals: UL, FM, ULC, VdS, and LPCB; Note: See Fire Protection Submittal Sheet for exact Listing / Approval information. Material: Cast: Figures: 201, 210, 219, 250, 260, 501, 510, 519, 510DE, 501S, 510S and 519S - Ductile iron conforming to ASTM A-536, Grade 65-45-12 Fabricated Steel: Figures 391, 392, 393, 312, 313, 321, 327, 341 and 350 - Carbon Steel, (Sizes 11/4" - 6" are Schedule 40); (Sizes 8" - 12" are Schedule 30), conforming to ASTM A-53 Grade B Protective Coatings: • Non -lead orange paint • Fire brigade red (optional) non -lead paint • Hot dipped galvanized conforming to ASTM A-153 Ordering Procedure When placing an order, indicate the full product name. Please specify the quantity, figure number, wall thickness, and size. Grinnell Grooved Piping Products, valves, accessories and other products are available throughout the U.S., Canada, and internationally, through a network of distribution centers. You may write directly or call 215-362-0700 for the distributor nearest you. Care and Maintenance The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in accordance with the applicable standards of the National Fire Protection Association (e.g., NFPA 25), in addition to the standards of any authority having jurisdiction. The installing contractor or product manufacturer should be contacted relative to any questions Any impairment must be immediately corrected It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service. Limited Warranty Products manufactured by Tyco Fire Products are warranted solely to the original Buyer for ten (10) years against defects in material and workmanship when paidforand properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by Tyco Fire Products. No warranty is given for products or components manufactured by companies not affiliated by ownership with Tyco Fire Products or for products and components which have been subject to misuse, improper installation, corrosion, orwhich have not been installed, maintained, modified or repaired in accordance with applicable Standards of the National Fire Protection Association (NFPA), and/orthe standards of any other Authorities Having Jurisdiction. Materials found by Tyco Fire Products to be defective shall be either repaired or replaced, at Tyco Fire Products' sole option. Tyco Fire Products neither assumes, nor authorizes any person to assumefor it, anyother obligation in connection with the sale of products or parts of products. Tyco Fire Products shall not be responsi ble forsprinklersystem design errors or inaccu rate orincomplete information supplied by Buyer or Buyer's representatives. IN NO EVENT SHALL TYCO FIRE PRODUCTS BE LIABLE, IN CONTRACT, TORT, STRICT LIABILITY OR UNDER ANY OTHER LEGAL THEORY, FOR INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIALDAMAGES, INCLUDING BUTNOT LIMITED TO LABOR CHARGES, REGARDLESS OF WHETHERTYCO FIRE PRODUCTS WAS INFORMED ABOUT THE POSSIBILITY OF SUCH DAMAGES, AND IN NO EVENT SHALL TYCO FIRE PRODUCTS' LIABILITY EXCEED AN AMOUNT EQUAL TO THE SALES PRICE. THE FOREGOING WARRANTY IS MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Page 1 of 6 September 2004 TFP1810 Page 3 of 6 TFP1810 Figures 501, 510, 519 and 510DIE Figure 501 r,toE i--CtOE J+ Figure 510 Figure 519 Figure 5- ODE Figure 501 45° Elbow Figure 510 90° Elbow Figure 519 Tee Figure 510DE 90' Drain Elbow Nominal Size C to E Inches mm Appx. Wt. Lbs. Kg. C to E Inches mm Appx. Wt. Lbs. Kg. C to E Inches mm Appx. Wt. Lbs. Kg. C to E Inches mm A In�nes tm B Inches mri Appx. Wt. Lbs. Kg. 1'/4" 1.75 44.5 0.9 0.4 2.75 69.9 1.0 0.5 2.75 69.9 1.4 0.6 1'!2° 1.75 44.5 1.1 0.5 2.75 69.9 1.2 0.5 2.75 69.9 1.8 0.8 2„ 2.00 50.8 1.8 0.8 3.25 82.6 2.0 0.9 3.25 82.6 2.7 1.2 - 2.25 2.2 3.75 3.0 3.75 5.8 3.75 2.00 2.75 2.7 2'!2° 57.2 1.0 95.3 1.4 95.3 2.6 95.3 E0.8 69.9 1.2 2.50 3.5 4.25 4.5 4.25 7.0 4.25 2.34 2.75 3.7 3 63.5 1.6 108.0 2.0 108.0 3.2 108.0 E9.4 69.9 7.7 4" 3.00 76.2 5.2 2.4 5.00 127.0 8.5 3.9 5.00 127.0 11.8 5.4 5.00 127.0 2.85 72.4 2.75 69..9 7.0 3.2 3.25 8.5 5.50 13.5 5.50 17.0 5.50 2.38 2.75 13.0 5 82.6 3.9 139.7 6.1 139.7 7.7 139.7 E5.9 69.9 5.9 3.50 12.0 6.50 18.5 6.50 26.0 6.50 3.92 2.75 13.4 6„ 88.9 5.4 165.1 8.4 165.1 11.8 165.1 &9.6 69.9 6.1 4.25 2:3.0 7.75 36.5 7.75 45.0 7.75 4.95 2.75 26.3 8„ 108.0 10.4 196.9 16.6 196.9 20.4 196.9 125.7 69.9 11.9 Figures 501S, 510S and 519S Figure 501S Friction Resistance 501S, 510S & 519S (Expressed as Equivalent Straight Pipe) Elbow Tee Size 90° 45° Branch Run Inches Feet Feet Feet Feet mm Meters Meters Meters Meters 2 3.2 1.6 8.0 3.2 60.3 1.0 0.5 2.5 1.0 21/2 3.9 2.0 9.8 3.9 73.0 1.2 0.6 3.0 1.2 76.1mm 1 1.2 2.1 0.6 10.3 3.1 4.1 1.2 3 4.9 2.4 12.2 4.9 88.9 1.5 0.7 3.7 1.5 4 6.5 3.3 16.3 6.5 114.3 2.0 1.0 5.0 2.0 139.7mm 6•0 2.4 4.1 1.3 20.0 6.1 8.0 2.4 5 6.2 4.1 20.5 8.2 141.3 2.5 1.3 6.3 2.5 165.1. - 2.9 4.8 1.4 23.8 7.2 `.5 2.9 6 9.9 5.0 24.8 5.9 168.3 ,?.0 1.5 7.6 3.0 8 13.1 6.6 32.8 13.1 219.1 4.0 2.0 10.0 4.0 4111 i--CtoE Figure 510S' CtoE Figure 519S' Figure 50-i S 45° Elbory Figure 510S 90° Elbow Figure 5I9S Tee Nominal Size C to E Inches mm Appx Wt. Las. Kg. C to E Inches mm App. Wt. LDS. Kg. C to E Inches mm Appx. Wt. Las. Kg. 2.00 11.8 2.75 1.5 2.75 2.1 2„ 50.8 (.3 69.9 0.7 69.9 1.0 2'/2° 2.25 57.2 2.2 7.0 3.00 76.2 2.2 7.0 3.00 76.2 3.0 7.4 76.1mm 2.25 57.2 2.2 1.0 3.00 76.2 2.3 7.0 3.00 76.2 3.1 7.4 2.50 3_5 3.38 3.0 3.38 4.1 3„ 63.5 7.6 85.9 1.3 85.9 1..9 3.00 5.2 4.00 5.6 4.00 7.7 4„ 76.2 2.4 101.6 2.6 101.6 5.5 3.25 7.7 4.88 8.6 4.88 12.0 139.7mm 82.6 5.5 124.0 3.9 124.0 5.4 3.25 8.5 4.88 8.8 4.88 12.0 5„ 82.6 3.9 124..0 3.9 124.0 5.4 3.50 12.0 5.50 11.00 5.50 15.0 165.1 mm 88.9 5 4 139.7 5.0 139.7 6.8 3.50 12.0 5.50 1' .2 5.50 15.2 6„ 88.9 5 d 139.7 5.1 139.7 6.9 4.25 2, .0 6.88 23.4 6.88 31.2 8„ 108.0 1 0. 4 174.8 10.6 174.8 14.2 'Note: Figure 510S and 519S fittings are necial short radius fi tings with sma lercenter to end dimensions th n standard grooved Titling . Depending on the size and coupling used there may be interterence al the holt pads which require repositioning of the coupling oriertatien. The use of flange adhpters is not recommended with Figur s 510S and 519S fittings. Contact'yco Fire Products for details. tqcci I Fire &Building Products Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500 www.tyco-fire.com Grinnell Grooved Fire Protection Products Figure 716 Flexible Reducing Coupling General Description OCR VdS See Fire Protection Submittal Sheet for Pressure Rating and Listing/Approval Information The Figure 716 Flexible Reducing Coupling allows a direct transition between two different pipe sizes, and replaces two couplings and a reducing fitting. It is capable of pressures up to 350 psig (2413 kPa) depending on pipe size and wall thickness when used in fire protection services. Note: Reducing Couplings are not recommended for dry pipe and freezer applications. WARNING The Figure 716 Flexible Reducing Coupling described herein must be installed and maintained in compliance with this document, as well as with the applicable standards of the National Fire Protection Association, in addition to the standards of any other authorities having jurisdiction. Failure to do so may impair the performance of this device. The owner is responsible for maintaining their fire protection system and devices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Technical Data Figure: 716 Sizes: 2" x 1 Yz" - 8" x 6° Approvals: UL, FM, ULC, VdS, and LPCB; See Fire Protection Submittal Sheet for exact Listing / Approval information. Housing: Ductile iron conforming to ASTM A-536, Grade 65-45-12 Protective Coatings: • Non -lead orange paint • Fire brigade red (optional) non -lead paint • Hot dipped galvanized conforming to ASTM A-153 Bolt/Nuts: Track Head Bolts - conforming to ASTM A-183, Zinc Plated, (Min. Tensile = 110,000 psif758,422 kPa) Metric - conforming to ASTM F568M Gasket: (specify when ordering) • Grade "E" EPDM, green color code (See Data Sheet TFP1895 for aid in selecting proper gasket) Ordering Procedure When placing an order, indicate the full product name. Please specify the quantity, figure number, type of gasket, Grade "E" EPDM, and size. Grinnell Grooved Piping Products, valves, accessories and other products are available throughoutthe U.S., Canada, and internationally, through a network of distribution centers. You may write directly or call 215-362-0700 for the distributor nearest you. Care and Maintenance The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in accordance with the applicable standards of the National Fire Protection Association (e.g., NFPA 25), in addition to the standards of any authority having jurisdiction. The installing contractor or product manufacturer should be contacted relative to any questions. Any impairment must be immediately corrected. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service. Limited Warranty Products manufactured by Tyco Fire Products are warranted solely to the original Buyer for ten (10) years against defects in material and workmanship when paid for and properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by Tyco Fire Products. No warranty is given for products or components manufactured by companies not affiliated by ownership with Tyco Fire Products or for products and components which have been subject to misuse, improper installation, corrosion, or which have not been installed, maintained, modified or repaired in accordance with applicable Standards of the National Fire Protection Association (NFPA), and/orthe standards of any otherAuthorities Having Jurisdiction. Materials found by Tyco Fire Products to be defective shall be either repaired or replaced, at Tyco Fire Products' sole option. Tyco Fire Products neither assumes, nor authorizes any person to assumeforit,anyotherobligation in connection with the sale of products or parts of products. Tyco Fire Productsshall not beresponsibleforsprinklersystem design errorsorinaccurateorincompleteinformation supplied by Buyer or Buyer's representatives. IN NO EVENT SHALL TYCO FIRE PRODUCTS BE LIABLE, IN CONTRACT, TORT, STRICT LIABILITY OR UNDER ANY OTHER LEGAL THEORY, FOR INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUTNOT LIMITED TO LABOR CHARGES, REGARDLESS OF WHETHERTYCO FIREPRODUCTS WAS INFORMED ABOUT THE POSSIBILITY OF SUCH DAMAGES, AND IN NO EVENT SHALL TYCO FIRE PRODUCTS' LIABILITY EXCEED AN AMOUNT EQUAL TO THE SALES PRICE. THE FOREGOING WARRANTY IS MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Page 1 of 2 July 2004 TFP1830 Page 2 of 2 Figure 716 Grooved Coupling TFP1 830 c Pipe Max. *$ End Gap Inches mm Max.t Pressure psi kPa Max.t End Load Lbs. N Nominal Dimensions Deflection $ Bolt Size * Dia. x Lg. Net W. t Lbs. Kg. Size O.D. Inches mm A Inches mm 6 Inches mm C Inches mm °Per Coupling Inches/ Foot mm/m 2" x 1'/2" 2.375 x 1.900 0.13 350 992 3.50 5.06 1.88 1 ° 53' 0.39 3/8" x 21/4" 2.0 60.3 x 48.8 3.3 2,413 4,412 88.9 128.5 47.8 32.5 M10 x 57 0.9 2.875 x 2.375 0.13 350 1,550 4.00 5.50 1.88 0.32 3/e" X 2'/4" 2.5 2 /z x 2"73.0 x 60.3 3.3 2,413 6,894 101.6 139.7 47.8 1° 33 26.7 M 10 x 57 1.1 76.1 X 60.3mm 3.000 x 2.375 0.13 350 1.550 4.19 5.88 1.88 1 ° 34' 0.32 M 12 X 76 3.1 76.1 x 60.3 3.3 2,413 6,894 106.4 149.4 47.8 26.7 1.4 3" x 2" 3.500 x 2.375 0.13 350 1,550 4.69 6.50 1.88 1 ° 17' 0.27 1/2" x 3" 4.5 88.9 x 60.3 3.3 2,413 6,894 119.1 165.1 47.8 22.5 M12 x 76 2.0 3" x 2'/2" 3.500 x 2.875 0.13 350 2,271 4.69 6.50 1.88 1 ° 17' 0.27 1/2" x 3" 4.6 88.9 x 73.0 3.3 2,413 10,101 119.1 165.1 47.8 22.5 M12 x 76 2.1 88.9 x 76.1 mm 3.500 x 3.000 0.13 350 2,474 4.69 6.50 1.88 1 ° 17' 0.27 M12 x 76 4.5 88.9 x 76.1 3.3 2,413 11,004 119.1 165.1 47.8 22.5 2.0 4" x 2" 4.500 x 2.375 0.19 350 1,550 6.00 8.13 2.00 2° 38' 0.55 5/8" X 31/4" 7.0 114.3 x 60.3 4.8 2,413 6,894 152.4 206.5 50.8 45.8 M 16 x 83 3.2 4" x 2'/2" 4.500 x 2.875 0.19 350 2,271 6.00 8.13 2.00 2° 38' 0.55 5/8" x 3'/4" 6.1 114.3x73.0 4.8 2,413 10,101 152.4 206.5 50.8 45.8 M16x83 2.8 114.3 x 76.1 mm 4.500 x 3.000 0.19 350 2,474 6.00 8.13 2.00 ° 2 38 0.55 M 16 x 83 6.2 114.3 x 76.1 4.8 2,413 11,004 152.4 206.5 50.8 45.8 2.8 4" x 3" 4.500 x 3.500 0.19 350 3,366 6.00 8.13 2.00 2° 38' 0.55 5/ " x 31/4" 6.2 114.3 x 88.9 4.8 2,413 14,972 152.4 206.5 50.8 45.8 M 16 x 83 2.8 139.7 X 114.3. 5.500 x 4.500 0.25 350 5,564 7.06 9.50 2.06 2° 38' 0.55 M20 X 121 11.0 139.7 x 114.3 6.4 2,413 24,749 179.3 241.3 52.3 45.8 5.0 5" x 4" 5.563 x 4.500 0.25 350 5,564 7.13 9.56 2.06 2° 5, 0.44 3/4" x 43/4" 10.1 141.3 x 114.3 6.4 2,413 24,749 181.1 242.8 52.3 36.7 M20 x 121 4.6 165.1 x 114.3mm 6.500 x 4.500 0.25 300 4,771 8.18 10.81 2.06 1 ° - 50' 0.38 M20 x 121 12'5 165.1 x 114.3 6.4 2,068 21,221 207.8 274.6 52.3 31.7 5.7 6" x 4" 6.625 x 4.500 0.25 300 4,769 8.38 10.88 2.06 1 ° 44' 0.36 3/4" x 43/4" 12.5 168.3 x 114.3 6.4 2,068 21,213 212.9 276.4 52.3 30.0 M20 x 121 5.7 6" x 5" 6.625 x 5.563 0.25 300 7,288 8.38 10.88 2.06 1 ° 44' •0.36 3/4" x 43/4" 11.7 168.3 x 141.3 6.4 2,068 32,417 212.9 276.4 52.3 30.0 M20 x 121 5.3 8" x 6" 8.625 x 6.625 0.25 300 10,336 10.69 13.75 2.25 1 ° 15' •0.26 7/8" x 6'/2" 23.5 219.1 x 168.3 6.4 2,068 45,975 271.5 349.3 57.2 21.7 M22 x 165 10.7 * Maximum available gap between pipe ends. Minimum gap = 0. t Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ on other pipe materials and/or wall thickness. Contact Tyco Fire Products for details. See Fire Protection Equipment Submittal Sheet for Listing and Approval pressure ratings. $ Max End Gap and Deflection is for cut grooved standard weight pipe. Values for rot grooved pipe will be '/z that of cut grooved. ** Gold color coded metric bolt sizes are available upon request. General Notes: It is the Designer's responsibility to select products suitable for the intended service and to ensure that pressure ratings and performance data is not exceeded. Always read and understand the installation instructions (IH-1000). Never remove any piping component or correct or modify any piping deficiencies without first depressurizing and draining the system. Material and gasket selection should be verified to be compatible for the specific application. Certified Company TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19946 Printed U.S.A. it two IFire & Budding Products Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500 www.tyco-fire.com Grinnell Grooved Fire Protection Products Figure 705 Flexible Coupling General Description LPCB VdS. See Fire Protection Submittal Sheet for Pressure Rating and Listing/Approval Information The Figure 705 Flexible Coupling is capable of pressures up to 300 psig (2068 kPa) depending on pipe size and wall thickness when used in fire protection services. It provides a dependable method of joining pipe and is suitable for use in a variety of applications. Rigid Couplings are recommended for dry pipe and freezer applications. WARNING The Figure 705 Flexible Coupling described herein must be installed and maintained in compliance with this document, as well as with the applicable standards of the National Fire Protection Association, in addition to the standards of any otherauthorities having jurisdiction. Failure to do so may impair the performance of this device. The owner is responsible for maintaining their fire protection system and devices in proper operating condition. The installing contractor or sprinkler manufacturer should be contacted with any questions. Technical Data Figure: 705 Sizes: 1 14" - 12" Approvals: UL, FM, ULC, VdS, and LPCB; See Fire Protection Submittal Sheet for exact Listing / Approval information. Housing: Ductile iron conforming to ASTM A-536, Grade 65-45-12 Protective Coatings: • Non -lead orange paint • Fire brigade red (optional) non -lead paint • Hot dipped galvanized conforming to ASTM A-153 Bolt/Nuts: Track Head Bolts - conforming to ASTM A-183, Zinc Plated, (Min. Tensile = 110,000 psi/758,422 kPa) Metric - conforming to ASTM F568M Gasket: (specify when ordering) • Grade "A" EPDMA violet color code ambientto+150°F (+66°C) forfire protection systems. Not recommended for hot water systems. • Tri-seal (Grade "E" EPDM), green color code. • Prelubricated (Grade "A" EPDMA) (See Data Sheet TFP1895 for aid in selecting proper gasket) Ordering Procedure When placing an order, indicate the full product name. Please specifythe quantity, figure number, type of gasket, Grade "A" EPDMA, Prelubricated (Grade "A" EPDMA) or Grade "E" EPDM Tri-Seal, and size. Grinnell Grooved Piping Products, valves, accessories and other products are available throughout the U.S., Canada, and internationally, through a network of distribution centers. You may write directly or call 215-362-0700 for the distributor nearest you. Care and Maintenance The owner is responsible for the inspection, testing, and maintenance of their fire protection system and devices in accordance with the applicable standards of the National Fire Protection Association (e.g., NFPA 25), in addition to the standards of any authority having jurisdiction. The installing contractor or product manufacturer should be contacted relative to any questions. Any impairment must be immediately corrected. It is recommended that automatic sprinkler systems be inspected, tested, and maintained by a qualified Inspection Service. Limited Warranty Products manufactured by Tyco Fire Products are warranted solely to the original Buyer for ten (10) years against defects in material and workmanship when paid forand properly installed and maintained under normal use and service. This warranty will expire ten (10) years from date of shipment by Tyco Fire Products. No warranty is given for products or components manufactured by companies not affiliated byownershipwith Tyco Fire Products orfor products and components which have been subject to misuse, improper installation, corrosion, or which have not been installed, maintained, modified or repaired in accordance with applicable Standards of the National Fire Protection Association (NFPA), and/orthe standards of any otherAuthorities Having Jurisdiction. Materials found by Tyco Fire Products to be defective shall be either repaired or replaced, at Tyco Fire Products' sole option. Tyco Fire Products neither assumes, nor authorizes any person to assumeforit,anyotherobligation in connection with the sale of products or parts of products. Tyco Fire Prod ucts shall not be responsi bleforsprinkler system design errorsorinaccurateorincompleteinformation supplied by Buyer or Buyer's representatives. IN NO EVENT SHALL TYCO FIRE PRODUCTS BE LIABLE, IN CONTRACT, TORT, STRICT LIABILITY OR UNDER ANY OTHER LEGAL THEORY, FOR INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIALDAMAGES, INCLUDING BUT NOT LIMITED TO LABOR CHARGES, REGARDLESS OF WHETHERTYCO FIRE PRODUCTS WAS INFORMED ABOUT THE POSSIBILITY OF SUCH DAMAGES, AND IN NO EVENT SHALLTYCO FIRE PRODUCTS' LIABILITY EXCEED AN AMOUNT EQUAL TO THE SALES PRICE. 1HE FOREGOING WARRANTYIS MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Page 1 of 2 July 2004 TFP1820 Page 2 of 2 Figure 705 Grooved Coupling TFP1820 ail Pipe Max. `$ End Gap Inches mm Max.t Pressure psi kPa Max.t End load Lbs. N Nominal Dimensions Deflec ion $ Bolt Size** Dia. x Lg. Net Wt. Lbs. Kg. Size O.D. Inches mm A Inches mm B Inches mm C Inches mm °Per Coupling Inches/ Foot mm/m 1.660 0.13 300 649 2.56 4.19 1.81 0.90 3/8" X 21/4" 1.5 1 1/4 42.4 3.3 2,068 2,887 65.0 106.4 46.0 4 19' 75.0 M 10 x 57 0.7 1.900 0.13 300 850 2.75 4.44 1.81 0 0.79 3/8" x 21/4" 1.6 1 1/2 48.3 3.3 2,068 3,781 69.9 112.8 46.0 3 - 46' 65.8 M10 x 57 0.7 2.375 0.13 300 1,328 3.25 4.88 1.88 0.63 3/8" x 21/4" 1.7 2„ 60.3 3.3 2,068 5,907 82.6 124.0 47.8 0 3 1 52.5 M 10 x 57 0.8 21/2" 2.875 73.0 0.13 3.3 300 2,068 1,947 8,660 3.69 93.7 5.50 139.7 1.88 47.8 2° - 29' 0.52 43.3 3/8" x 21/4" M10 x 57 2.0 0.9 3.000 0.13 300 2,120 4.00 5.75 1.88 0.50 3.1 76.1. 76.1 3.3 2,068 9,430 101.6 146.1 47.8 20 23' 41.7 M12 x 76 1.4 3„ 3.500 0.13 300 2,885 4.38 6.50 1.88 20 3, 0.43 1/2" x 3" 3.0 88.9 3.3 2,068 12,832 111.3 165.1 47.8 35.8 M 12 x 76 1.4 108.108.0. 4.250 108.0 0.25 6.4 300 2,068 4,256 18,931 5.50 139.7 7.50 190.5 2.06 52.3 30 22' 0.70 58.3 M12 X 76 4.2 1.9 4.500 0.25 300 4,769 5.69 7.75 2.06 0 0.67 1/2" x 3" 4.0 4 114.3 6.4 2,068 21,213 144.5 196.9 52.3 3 11 55.8 M12 x 76 1.8 133.0mm 5.250 133.0 0.25 6.4 300 2,068 6,494 28,885 6.56 166.6 9.50 241.3 2.06 52.3 20 _44' 0.56 46.7 M16 x 83 7.2 3.3 139.139.7. 5.500 139.7 0.25 6.4 300 2,068 7,127 31,701 6.81 173.0 9.75 247.7 2.06 52.3 20 36' 0.56 46.7 M16 x 83 7.2 3.3 5.563 0.25 300 7,288 6.88 9.75 2.06 0 0.54 5/8" x 31/4" 7.0 5 141.3 6.4 2,068 32,417 174.8 247.7 52.3 2 35 45.0 M16 x 83 3.2 159.0mm 6.250 159.0 0.25 6.4 300 2,068 9,204 40,939 7.56 192.0 10.31 261.9 2.06 52.3 20 17' 0.48 40.0 M16 x 83 7.4 3.4 6.500 0.25 300 9,950 7.75 10.69 2.06 .Z0 0.46 7.1 165.1.165.1 6.4 2,068 44,258 196.9 271.5 52.3 12, 38.3 M16 x 83 3.2 6.625 0.25 300 10,336 7.94 10.69 2.06 00.45 5/8" x 31/4" 7.1 6 168.3 6.4 2,068 45,975 201.7 271.5 52.3 2 10'37.5 M16 x 83 3.2 216.3.8.500 216.3 0.25 6.4 300 2,068 17,024 75,723 10.07 255.8 13.50 342.9 2.31 58.7 10 40' 0.35 29.2 M20 x 121 12.4 5.6 8.625 0.25 300 17,519 10.19 13.56 2.50 00.35 3/4" x 43/4" 14.5 8 219.1 6.4 2,068 77,925 258.8 344.4 63.5 1 40'29.2 M20 x 121 6.6 10" 10.750 273.0 0.25 6.4 250 1,724 22,679 100,876 12.69 322.3 16.38 416.1 2.63 66.8 10 20, 0.28 23.3 1" x 6'/2" M24 x 165 28.0 12.7 12" 12.750 323.9 0.25 6.4 250 1,724 31,903 141,905 14.94 379.5 18.88 479.6 2.63 66.8 10 7, 0.23 19.2 1" x 61/2" M24 x 165 36.5 16.6 * Maximum available gap between pipe ends. Minimum gap = 0. t Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ on other pipe materials and/or wall thickness. Contact Tyco Fire Products for details. See Fire Protection Equipment Submittal Sheet for Listing and Approval pressure ratings. ** Gold color coded metric bolt sizes are available upon request. $ Max End Gap and Deflection is for cut grooved standard weight pipe. Values for roll grooved pipe will be ' that of cut grooved. General Notes: It is the Designer's responsibility to select products suitable for the intended service and to ensure that pressure ratings and performance data is not exceeded. Always read and understand the installation instructions (IH-1000). Never remove any piping component or correct or modify any piping deficiencies without first depressurizing and draining the system. Material and gasket selection should be verified to be compatible for the specific application. Certified Company TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19946 Printed U.S.A.