HomeMy WebLinkAboutXR2023-3216 - Alternative Material & MethodsCITY OF NEWPORT BEACH
04
COMMUNITY DEVELOPMENT DEPARTMENT
U M► S BUILDING DIVISION
r r 100 Civic Center Drive I P.O. Box 1768 1 Newport Beach, CA 92658-8915
,lrcORK\ www.newoortbeachca.dov 1 (949) 644-3200
CASE NO.:
❑ REQUEST FOR MODIFICATION TO PROVISIONS
OF TITLE 9 (FIRE CODE) OR TITLE 15 (BUILDING CODE)
OF THE NEWPORT BEACH MUNICIPAL CODE
(See Reverse for Basis for Approval) (Fee $306)
® REQUEST FOR ALTERNATE MATERIAL
OR METHOD OF CONSTRUCTION
(See Reverse for Basis for Approval) (Fee $306)
For above requests, complete Sections t, 2 8 3
below by printing in ink or typing.
FOR STAFF
RECEIVED BY
COMMUNITY
DEVELOPMENT
OCT 272023
CITY OF
NEWPORT BEACH
Plan Check # rc. wLS-' 9 # of Stories I
Occupancy Classifi 'on R3lo
Use of Building $ Z # of Units
Project Status
Construction Tyr
Verified by
No. of Items
Fee due
DISTRIBUTION:
❑ Owner jM Plan Check�N
® Petitioner ❑ Inspector
❑ Fire ❑ Other
1 I JOB ADDRESS: I PETITIONER: 11
SITE ADDRESS: I I Singletrce Drive Petitioner Randy Hecht (McCormick Construction)
Owner Joe Famqui (PeWoner to be emhQ for er imed
Address I l Sinalctrec Drive Address 916 No. Main Street
Newport Beach CA Zip 92660 Orange, CA Zip 92867
Daytime Phone ( 949 ) 439-1194 Daytime Phone ( 951 ) 847-1996
Email: 1) B'JIL.DA,*AA7MUAL5 COHri
3 uUSTIFICATION/FINDINGS OF EQUIVALENCY: CODE SECTIONS:
CG 4.504.2.1
of
Petitioner's /C// J� Position Engineer
Signature CA Professional Lic. # C055637
10-15-20'3
FOR USE ONLY
rr_//STAFF
DEPARTMENT ACTION: In accordance with: lY� CBC 104.11/CFC 104.9
Alternate materials & methods)
❑ Concurrence from Fire Code Official is required. ❑ Approved ❑ Disapproved
By: Date
Request (DOES) ssen any fire protection requirements.
..quest (DOE (DOES NO ssen the structural integrity
❑ CBC 104.t 0/CFC 104.8
(CBC Modification)
❑ Written Comments Attached
The Request is:
ranted ❑ Denied (See reverse for appeal information)
❑ Granted (Ratification required)
Conditions of Approval:
Si
Print Name I
Position CHIEF 8I111 DING CIEROW
N—off �- Zo2
APPEAL OF DIVISION ACTION TO THE BUILDING BOARD OF APPEALS (See Reverse)
(Signature. statement of ownerorapplicant, statementoffrLreasons forappeal and filing fees are required.)
CASHIER RECEIPT NUMBER` Q 19 /V� Zo2 Fonnslmodif 08/21/23
�PQA
SLAB 3 GOATS MIN.
IS MIL ASTM P 3010
PEIA
r (E) R-11S NSUL
(E) 4X BE
(E)se` TYPE'X' G--YP.
(N) b MIL
VISOUEEN
(M GIXJC �4 REBAR
TYP
CN) R-15
5ECTION A -A
SECTION B-B
Joe Faruqui
11 Singletree Drive
Newport Beach, CA 92660
(949)439-1194
INSUL
(E) e" TYPE "X" GYP.
(N) STUD WALL (NON -LOAD SEARING)
G' MIN. TYPE 'X" IHR
0.0. ESP--199
\^� 916 North Main Street
1 1�1 McCormickSery Cons
Ceestruction Orange, CA 92867
TEL: (951) 847-1996
State License No. 947885
PERQ
Na. C055637
Exp 12-31-24
10-25-9023
BY: —
DATE: 10-25-2023
SCALE: NONE
Sika° MB
Solvent Free, Epoxy Moisture Barrier
PRODUCT DESCRIPTION
Sika® MB is a 2-component, solvent free, low viscosity,
epoxy for use under wood flooring products, self leveling
underlayments, floating floors and other flooring
systems that require protection from subfloor moisture.
USES
• Moisture barrier to help control moisture. propagation
in cementitious substrates with a moisture content not
exceeding 6 % by Tramex Method, residual moisture
up to 100 % R.H. or 25 Ib/1,000 ft2/24 h (11.4 kg/92.9m
2/24 h)
• For substrate consolidation on concrete, cement and
gypsum screeds
• Adhesion promoter for old and new adhesive residues
in conjunction with other Sika® products
• Suitable on concrete, cement, self -leveling and gypsum
substrates, CSB, plywood, quarry and terrazzo tiles,
water-soluble adhesive and cutbacks
PRODUCT INFORMATION
CHARACTERISTICS / ADVANTAGES
• Solvent -free (100 `e solids)
• Easy roller applied application, low viscosity
• Convenient, easy to mix packaging
• Shorter construction periods
• Excellent penetration and stabilization of the substrate
• Reduction of adhesive consumption
• Suitable for use on floors with radiant heating
• Compatible with SikaBond® wood flooring adhesives,
Sikaa Level products
• Can be used below floating floors
APPROVALS/STANDARDS
• Meets ASTM F 3010
Chemical Base Two component epoxy
Packaging 2.64 gal (10 L) pail
Color Blue
Shelf Life 24 months from date of production if stored properly in undamaged sealed
containers
Storage Conditions Store dry at 50-77 °F (10-25 °C). Protect from moisture.
Density 69 Ib/ft3 (1.1 kg/1)
TECHNICAL INFORMATION
Product Data Sheet
Ska• Me
lone 20", verlun 01 IN
02051308100000001)
1/4
Shore D Hardness 7 days 83 (mixed A&B) (ASTM D-2240)
Compressive Strength 7 days 10,000 psi (69 MPa) 73 `F (23 °q
50 % R.H.
Permeabilityto Water Vapor 0.06 g/M2-24hour-mmHG (ASTM E-96)
Service Temperature -40-158'F(-40-70'C)
APPLICATION INFORMATION
Coverage
Coverage per pail
Moisture barrier
250-300 ft� (23.2-27.9 ri
Adhesion promoter or
40D-450 ft= (37.2-41.9 m2)
surface consolidator
(Coverage figures do not include allowance
for surface profile and porosity or material waste).
Application
Recommended Results in
Coatings
Moisture barrier only
min.I Mirror like finish
Substrate
min. 1 Good penetration
consolidation only
Adhesion promotion
min. 1 Mirror like finish
Moisture barrier+ min. 2 Mirror like finish
substrate consolidation
Moisture barrier+ min. 2 Mirror like finish
adhesion promotion
MUST produce a monolithic, pinhole -free finish with a continuous film. The
need for multiple coats is directly related to surface absorption.
Pot Life 50 "F (10 "C) - 60 minutes
68 "F (20'Q "' 30 minutes
86'F (30 °C) - 15 minutes
Cure Time 50 °F (10 °C) 18 hours
73 °F (23'C) 8 hours
86 "F (30'C) 6 hours
*Minimum curing time, prior to walking on primer/or for applying Sikaeond' or Sika' Level.
Application Time Overcoating Application Minimum Maximum
Time Window`
Sika® MB 8 hours 36 hours
(2nd coat)
*When Sika® MB is left on the substrate for more than the maximum allowable open time, the surface must
be mechanically prepared (i.e. sanded) solvent wiped before proceeding.
Product Data Sheet
Sika° M6
—ne 201 s:or. p�SM
"5120&1 btl^00017
2/4
APPLICATION INSTRUCTIONS
SUBSTRATE PREPARATION
• Substrate must be clean, dry, sound and
homogeneous, free from oils, grease, dust, and loose
or friable particles. Paint, laitance, and other poorly
adhering contents must be mechanically removed.
• Substrate must have an open textured surface to allow
Sika® MB to penetrate. (i.e. Blast cleaning, grinding are
considered acceptable means to achevie the desired
surface profile. Acid and chemical etching are not
acceptable).
• At least 50 % of the surface area must be cleared of
residual adhesive and cutbacks. (i.e. by grinding or
mechanical substrate preparation)
• Old cutback can contain asbestos which is dangerous
for the health so do not grind, sand or blast. Refer to
the Resilient Floor Covering Institute's publication
"recommended work practice for removal of resilient
floor coverings" for instruction.
• Minimum substrate compressive strength > 1,160 psi.
Tensile Bond strength > 116 psi at the time Sika® MB is
applied.
• Repair with Sika' Level SkimCoat or Sika Quick' mortar
before priming.
• The floor must be cleaned with an industrial vacuum
prior to installation of the Sika® MB.
• On fiber reinforced concrete, fibers should be flamed
off the surface prior to application of Sika* MB as a
moisture barrier.
• Before overall installation begins, Sika' recommends
the application of several small test patches to
determine primer application requirements and
acceptability of final product performance.
MIXING
• Add one full can of component A to one full can of
component B then mix with an electric drill and mixing
(Jiffy Mixer type) paddle at a low speed to reduce air
entrainment (300-400 rpm). Using a paint stick or
similar is not sufficient to mix the primer.
• A minimum mixing time of 3 minutes shall be
observed; mixing shall continue until a homogeneous
mix has been achieved.
• Scrape sides of pail with paint stick or paddle to ensure
all contents are thoroughly mixed together.
• Unmixed material applied to the floor will not cure
properly.
APPLICATION METHOD / TOOLS
• Apply Sika® MB uniformly (in 2 directions 90') to the
substrate using a medium nap roller, ensuring that a
continuous coat is achieved over the entire surface
(MUST produce a mirror like finish).
• Pour contents of pail onto the floor for best working
time. Attempting to work from the pail will reduce
working time.
• When used as a moisture barrier and substrate
consolidation / adhesion promotor, prepare the
Product Data sheet
5ika' MB
rune 2019, versbn '14
G2D51'..08,t090CAn01?
substrate mechanically as in accordance with the
guidelines stated in subtitle "Surface Preparation".
Apply the first coat at 10 mils Apply the second coat at
15 mils in accordance with the open time*.
2 coats application: Apply the first coat at 75-115 ft2/gal
Apply the second coat at 151 ft2/gal in accordance
with the application time window*. Then follow one of
the option:
• Ootion 1: Broadcast to refusal with oven dried silica
sand (20/30) on the second coat immediately. Sweep
sand once the epoxy is cured. Apply Sika® Level
products on cured epoxy.
• Option 2: Apply Sika® Level-02 EZ Primer in accordance
with the application time window*. When the primer is
dry, apply Sika® Level products.
'ref. to appliction time in sections above
[9 111 1111I11 W612 idol[a
• Clean all tools and application equipment with cleaning
solvent (Xylene, MEK are effective).
• Hardened/cured material can only be removed
mechanically.
LIMITATIONS
• Proper coverage must be used to achieve moisture
barrier properties.
• Will not act as a moisture barrier for gypsum screeds.
Gypsum based subfloors are very susceptible to excess
moisture and will be degraded if exposed to excess
moisture from below or above.
• Only protects from moisture coming from below the
concrete.
• Will not prevent hydrostatic pressure.
• Must not be applied to a visibly wet substrate.
• Does not prevent moisture occurring between the
epoxy and the floating floor due to secondary sources
of moisture or acclimation, e.g. water condensation.
• Is not suitable for use with bonded systems due to
possible curing and adhesion problems.
• Sika* recommends the use of Sika' Level products on
top of it.
• Floor covering manufacturer's and Wood flooring
manufacturer's recommendations, like room humidity
levels and wood acclimation requirements should be
strictly followed.
• Sika' does not make any standing recommendations as
to the structural integrity of old adhesive residues or
subflooring materials that are not manufactured by
Sika'.
• When left on the substrate for more than the
maximum allowable open time of 36 hours, prior to
placing the adhesive, the surface must be thoroughly
cleaned and mechanically prepared (i.e. screened
sand) and solvent wiped. Failure to do this, may result
in adhesion problems. For detailed instruction contact
our Technical Service. When used in conjunction with
Sika Bond', Sika* MB does not need to be broadcasted
with sand.
3/4
BUILDING TRUST
BASIS OF PRODUCT DATA
LEGAL DISCLAIMER
Results may differ based upon statistical variations
depending upon mixing methods and equipment,
temperature, application methods, test methods, actual
site conditions and curing conditions.
OTHER RESTRICTIONS
See Legal Disclaimer.
ENVIRONMENTAL, HEALTH AND SAFETY
For further information and advice regarding
transportation, handling, storage and disposal of
chemical products, user should refer to the actual Safety
Data Sheets containing physical, environmental,
toxicological and other safety related data. User must
read the current actual Safety Data Sheets before using
any products. In case of an emergency, call CHEMTREC
at 1-900-424-9300, International 703-527-3887.
Sika Corporation
Sika Mexicana S.A. de C.V.
101 Polito Avenue
Ca rretera Libre relays Km. 85
Lyndhurst, N1 D7071
Facc Industrial Balvanea
Phone :+1-800-933-7452
Corregidora, Queretaro
Fax'.+1-2D1-933-6225
C.P. 76920
,,aslkaacom
Phone: 52 442 2385800
Fax52 442 2250537
Product Data Sheet
Skoa Me
0'_11, e s 0
t r ,120 n 1i00 -
• KEEP CONTAINER TIGHTLY CLOSED
• KEEP OUT OF REACH OF CHILDREN
• NOT FOR INTERNAL CONSUMPTION
• FOR INDUSTRIAL USE ONLY
• FOR PROFESSIONAL USE ONLY
Prior to each use of any product of Sika Corporation, its
subsidiaries or affiliates ("SIKA"), the user must always
read and follow the warnings and instructions on the
product's most current product label, Product Data
Sheet and Safety Data Sheet which are available at
usa.sika.com or by calling SIKA's Technical Service
Department at 1-800-933-7452. Nothing contained in
any SIKA literature or materials relieves the user of the
obligation to read and follow the warnings and
instructions for each SIKA product as set forth in the
current product label, Product Data Sheet and Safety
Data Sheet prior to use of the SIKA product.
SIKA warrants this product for one year from date of
installation to be free from manufacturing defects and
to meet the technical properties on the current Product
Data Sheet if used as directed within the product's shelf
life. User determines suitability of product for intended
use and assumes all risks. User's and/or buyer's sole
remedy shall be limited to the purchase price or
replacement of this product exclusive of any labor costs.
NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL
APPLY INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL
THEORY FOR SPECIAL OR CONSEQUENTIAL DAMAGES.
SIKA SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS
PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT
OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD
BY OTHERS.
Sale of SIKA products are subject to the Terms and
Conditions of Sale which are available at
https:Husa.sika.com/en/group/SikaCorp/termsandconditions.html
or by calling 1-800-933-7452.
Si ka IVE-En-lS-106-2019i-1-4.IA'
4/4
BUILDING