The URL can be used to link to this page

Home My WebLink About20130516_Home Elevator Manufacters Specs Planning MACHINE ROOMLESS TRACTION DRIVE 950 lb. AMERICA’S MOST CUSTOMIZABLE ELEVATOR Guide INCLINATOR LX® MACHINE ROOMLESS TRACTION DRIVE 4 LX - MRL TRACTION DRIVE Hoistway Layout The following specs are to be provided by the General Contractor (GC), except as noted, prior to Elevator Contractor (EC) installing the elevator equipment. 1. Enclosed, plumb and square hoistway with smooth interior surfaces. Include for fascias or furring of hoistway interior. 2. Doors, frames and door hardware. 3. Finish openings as per elevator contractor’s shop drawings. 4. Hoistway door security: All hoistway doors require door locking devices (provided by Inclinator) as well as a door handle and a latch set. All doors must be swing type (single hinge). Solid core doors are recommended. 5. Unfinished/Un-installed door: EC may prefer a minimum of one hoistway door and associated framing be left unfinished to accommodate elevator installation and prevent possible damage to door/framing. Preferably at the lowest floor. 2 LX - MRL TRACTION DRIVE Introduction It started over 85 years ago with a passion to help an ailing friend access his multi-level home. Now, almost a century later, the Inclinator craftsmanship can be found in more American homes today than any other brand. We want to use our heritage of service to enhance each stage of your building or remodeling experience and to help you create a uniquely personalized elevator for your home. Of all the stages, none is quite as exciting as the initial design phase. It’s where you begin to imagine the possibilities of something that’s uniquely yours. A home is personalized by the components you choose to fit your needs. Our Planning Guide is designed to simplify and assist architects, contractors, home owners and dealers in planning for a home elevator that meets the requirements of ASME A17.1 We recommend you contact an authorized dealer in the area where the elevator will be installed. They will be knowledgeable about local codes and restrictions. Become familiar with all requirements governing the installation and use of elevators in private residences. It is extremely important for you to know and adhere to all regulations concerning installation. This Planning Guide provides nominal dimensions and specifications useful for the initial planning of an elevator project. Before beginning actual construction, be sure to contact a local authorized dealer and obtain approval drawings customized with specifications and dimensions for your specific project. Call 1-800-343-9007 to find a local dealer or visit our website, www.inclinator.com. Inclinator elevators manufactured and installed under the proper parameters are warranted for 2 years. We assume no liability for equipment not installed in compliance with national, state, and local codes. LX - MRL TRACTION DRIVE 3 Table of Contents Hoistway Layout ............................................... 4-8 Hoistway Construction ........................................ 9 Hoistway Specifications .................................... 10 Hoistway Elevation ............................................ 11 Pit Specifications ............................................... 12 Technical Specifications .................................... 12 Controller Space ............................................... 13 Warranty ............................................................ 14 Steps of planning for an Inclinator LX Elevator 1. Locate local dealer and together determine the following: a. Select a drive system, cab type and design specifications b. Address national, state and local code requirements c. Determine installation parameters of site 2. Obtain approval drawings before building hoistway, doorways, pit, and any other construction related to the elevator 3. Coordinate with dealer to order and install the elevator LX - MRL TRACTION DRIVE 5 Hoistway Layout The following data is for typical industry size elevators. Any size cab is available in ¼” increments to dimensions A and C or B and D within the maximum and minimum dimensions shown in the diagram on page 4 not to exceed 15 SQ. FT. - Applicable to standard size wheelchairs \ CODE 1 CODE 2 CODE 3 6 LX - MRL TRACTION DRIVE Hoistway Layout The following data is for typical industry size elevators. Any size cab is available in ¼” increments to dimensions A and C or B and D within the maximum and minimum dimensions shown in the diagram on page 4 not to exceed 15 SQ. FT. CODE 4 CODE 5 CODE 6 LX - MRL TRACTION DRIVE 7 Hoistway Layout CODE 4,5 CODE 3,6 CODE 5,1 CODE 5,2 8 LX - MRL TRACTION DRIVE Hoistway Layout ADDITIONAL CONFIGURATIONS There are many additional layout options available. Please contact Inclinator or your local dealer for further assistance on shaft configurations. LX - MRL TRACTION DRIVE 9 Hoistway Construction 5-3 RULE / DOOR FRAME DETAILS RAIL DETAILS SUPPORT WALL DETAIL NOTE: * FRAMING ON DOOR SIDE OF HOISTWAY MUST BE OF 2x4 CONSTRUCTION TO APPLY TO 5-3 RULE OF ANSI 17.1 CODE. NOTE: WHEN STUD AND SHEETROCK CONSTRUCTION IS USED ON THE RAIL BRACKET SUPPORT WALL, DBL 2x6 STUDDING IS NEEDED TO MOUNT THE RAIL BRACKETS. DO NOT USE METAL STUDS. DOOR SILLS TO BE INSTALLED BY GC AFTER THE LIFT SUPPLIER HAS INSTALLED A RUNNING PLATFORM. SILL MUST BE BROUGHT OUT TO NOT LESS THAN ½” AND NOT MORE THAN 1 ¼” TO THE RUNNING PLATFORM WHILE MAINTAINING A DISTANCE OF 3” FROM THE HOISTWAY FACE OF THE LANDING DOOR (OR GATE) TO THE HOISTWAY EDGE OF THE LANDING SILL. 10 LX - MRL TRACTION DRIVE Hoistway Specifications The following specs are to be provided by the General Contractor (GC), except as noted, prior to Elevator Contractor (EC) installing the elevator equipment. 1. Environmental requirements for hoistway: a. Temperature should be maintained between 400 F to 1000 F. b. Should not be exposed to the elements. 2. Pit Requirements: a. Substantial level pit floor slab to support 3,123 lbs. impact load. b. Waterproof pit minimum 8” below lowest floor level, unless buffer springs are required then minimum 12” pit required. 3. Overhead Requirements: a. If minimum 8’6” OH is not possible, consult Inclinator, or EC, about possible solutions. 4. Rail Support Wall Requirements: a. The support wall consists of a double 2” x 6” bonded & nailed planking that is then constructed within a typical wood 2” x 4” studded wall. These double 2” x 6” planks are oriented and mounted perpendicular to the standard wall construction, all of these must be installed plumb and straight. b. The dual steel “T” rail assembly provided by Inclinator is to be mounted to the double stud planking plumb and straight along the vertical plane. c. The rail brackets are secured to the double 2” x 6” planking with ½” x 4” lag bolts, see drawing details. d. All studs in the rail support wall must be of wood, typical steel studs are prohibited and cannot be used in the rail support wall. e. Consult factory or dealer for concrete or steel framed construction. 5. ASME 17.1 Part 5.3: Hoistway to be constructed in accordance with this code and all local codes. It is the responsibility of the GC and the EC to comply with all appropriate codes. LX - MRL TRACTION DRIVE 11 Hoistway Elevation 12 LX - MRL TRACTION DRIVE Pit Specifications Rail Reactions LX - MRL TRACTION DRIVE 13 Controller Space 1. Permanent 230 volt, single phase, 30 amp dedicated circuit to operate the elevator. 2. 120 volt lighting supply and disconnect by others. 3. Telephone connection: Code requires a telephone connection. A phone line must be installed leading to the controller. 4. Recommended maximum distance from controller to hoistway box is 10’. 5. N.E.C. Regulations a. Minimum 30” x 36” clear unobstructed floor space in front of controller. 14 LX - MRL TRACTION DRIVE Warranty This warranty and all implied warranties including the implied warranties of merchantability and fitness for a particular purpose, for this product are limited to a period of two years from the time this product is first installed. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. The manufacturer is not responsible for consequential damages resulting from the use of this product, including labor charges for removal and reinstallation of parts. The manufacturer’s liability for any damages resulting from use of this product or breach of this or any implied warranties is limited solely to parts, repair or replacement in accordance with the terms set forth above and these are the exclusive remedies available to purchasers of this product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. LX - MRL TRACTION DRIVE 15 16 LX - MRL TRACTION DRIVE 601 Gibson Blvd, Harrisburg, PA 17104 | 800-343-9007 | www.INCLINATOR.com LX MRL TRACTION PLANNIG GUIDE – 02/05/2012