Loading...
HomeMy WebLinkAbout14 - Purchase of Rescue Ambulance14-1 NEWPORT BEACH City Council Staff Report COUNCIL STAFF REPORT CITY OF April 12, 2016 Agenda Item No. 14 ABSTRACT: Emergency Medical Services are a vital part of the service delivery for the Newport Beach Fire Department. The Fire Department responds to over 8,250 medical requests for service each year. A rescue ambulance provides lifesaving personnel and equipment to the residents and visitors of Newport Beach. In FY15, a Newport Beach resident donated $250,000 for the purchase of a new rescue ambulance. The only stipulation requested by the donor was that the unit displays an identifier reading “Donated by a Newport Beach Resident.” Fire and Municipal Operations Department staff developed a new ambulance specification and sought competitive proposals for the purchase of the new unit. The new rescue ambulance will provide a higher level of service while reducing costs and staff time for maintenance. RECOMMENDATION: a) Approve the purchase of one ambulance from Halcore Group, Inc., DBA Leader Industries for a total cost of $266,732.19; b) Approve and authorize the Mayor and City Clerk to sign the Purchase Agreement with Halcore Group, Inc., DBA Leader Industries for this purchase; and c) Approve Budget Amendment No. 16BA-037 to increase expenditure appropriations by $266,732.19 in the Equipment Replacement Fund account 7529032-911016 in the Municipal Operations Department. TO:HONORABLE MAYOR AND MEMBERS OF THE CITY COUNCIL FROM:Mike Pisani, Municipal Operations Director - 949-644-3055, mpisani@newportbeachca.gov PREPARED BY:Angela Crespi, Administrative Manager – 949-644-3352 Rachel Wilfert, Management Assistant – 949-644-3010 TITLE:Purchase of Rescue Ambulance Purchase of Rescue Ambulance April 12, 2016 Page 2 14-2 FUNDING REQUIREMENTS: $250,000 was donated by a Newport Beach resident and recorded as revenue in FY15. The remaining $16,732.19 is requested from the unappropriated fund balance in Equipment Fund. The purchase will be expensed from the Equipment Replacement Division in the Municipal Operations Department, Account 7529032-911016. DISCUSSION: The Fire Department operates a fleet of seven medic units. Three of the units are in service 24 hours per day, seven days per week, and a fourth is used in a surge capacity in times of high call volume when all primary rescue ambulances are busy. The remaining three reserve ambulances are deployed as primary response vehicles when other units are out of service for maintenance and repair or during large community events. Exhibit A: Fire Department Rescue Ambulance Fleet Year Make/Model Unit #Miles 2003 Ford E-450 2641 127,630 2005 Ford E-450 2634 79,330 2008 Ford E-450 2644 76,502 2008 Ford E-450 2645 114,817 2013 International 2646 38,248 2013 International 2647 45,832 2013 International 2648 41,001 The City Vehicle/Equipment Guidelines (Council Policy F-9) states that frontline paramedic ambulances should normally be replaced after 100,000 miles or 8 years. After the useful life of a front line ambulance, the unit is placed on reserve for an additional 4 years. The ambulance to be replaced was purchased in 2005. While it is not the oldest unit in the fleet, an assessment of the operational costs and engine reliability indicate that it is the most appropriate for replacement. The City’s Fire Apparatus Committee developed a vehicle specification and the Finance Department released Request for Proposal (RFP) No. 16-24 on January 5, 2016, soliciting proposals for one (1) emergency ambulance medical vehicle. In addition to being sent to known ambulance dealers, the RFP was also posted on the City’s PlanetBids portal for public viewing and distribution. Following a pre-proposal meeting and providing answers to questions from prospective respondents, the RFP closed on Purchase of Rescue Ambulance April 12, 2016 Page 3 14-3 February 5, 2016. The City received two (2) proposals from the following dealers: Emergency Vehicle Group, Inc., and Leader Industries, Inc. It was reiterated throughout the RFP process and during the pre-proposal meeting that requirements listed in the vehicle specifications were identified as minimums and designed to convey the City’s current ambulance operating standards. If the specified requirements could not be provided, proposers were asked to list any deviations and identify the benefit served to the City, if any. Deviations to the listed vehicle specifications were considered acceptable as long as they met existing federal standards for ambulance vehicles (hereby referred to as the “Federal K standards”). The evaluation panel for this selection process consisted of the City’s Fire and Municipal Operations Department staff members. Panelists were selected due to their experience and understanding of the operation, technical functionality and maintenance of emergency ambulance medical vehicles. Each member of the evaluation panel was provided a copy of the proposals as well as an evaluation matrix to score the proposals. Exhibit B describes the criteria used for evaluating the proposals: Exhibit B: Proposal Evaluation Criteria Evaluation Criteria Percentage of Score Qualifications & Experience of the Proposer 20% Technical Functionality of the Proposed Ambulance 40% Warranty and Service Considerations 10% Proposed Pricing 30% Evaluation of the proposals encompassed a two-step scoring process. In the first step, known as the “Technical Evaluation,” the panel was responsible for scoring the proposal against the evaluation criteria, except for pricing. The panelist all scored the proposals individually and the average of the scores is considered as the Technical Evaluation Score. In the second step of evaluation, the Cost Ratio Analysis, the Purchasing Division identified the unit cost of the ambulance provided by each proposer. The proposal containing the lowest unit cost (Leader Industries) was assigned the maximum of 30 points; the other proposal was assigned a score in proportion to 30 points that represented the percentage disparity between their proposed unit cost and the lowest proposed unit cost. Exhibit C below summarizes the scoring process: Purchase of Rescue Ambulance April 12, 2016 Page 4 14-4 Exhibit C: Proposal Scoring Summary Proposer Average Technical Score (Step 1) Cost Ratio Score (Step 2) Aggregate Score (Out of 100) Leader Industries, Inc.68.33 30.00 98.33 Emergency Vehicle Group, Inc.41.67 29.29 70.96 Of the two (2) proposals, the Leader Industries, Inc. proposal was unanimously scored as the most qualified dealer and ambulance for this project. The evaluation panel scored this proposer exceptionally high in the areas of technical functionality and qualifications and experience. The references provided by this proposer were also impressive, including a project history of providing ambulances to California public agencies such as the cities of San Francisco, Long Beach, Palo Alto and Burbank. The proposed unit from Emergency Vehicle Group, Inc. contained some exceptions to the vehicle specifications. While most of these exceptions met Federal K standards, there were two that stood out to the evaluation panel. The first exception concerns the curbside front compartment, which was listed in the vehicle specifications to measure 83.6”H x 26.7”W x 30”D in order to properly fit assorted ambulance equipment and accessories. The Emergency Vehicle Group, Inc. proposal called for this compartment to measure 85.75”H x 21.75”W x 30”D. Furthermore, the only way to maintain the requested dimensions is to move the curbside door and compartment toward the rear of the vehicle, causing the squad bench to be shortened by 6”, which is another deviation to a clearly defined specification requirement. These exceptions summarize the rationale for the lower Technical Score assigned to Emergency Vehicle Group, Inc. Upon conclusion of this RFP evaluation process, the evaluation panel recommended award of this purchase to Leader Industries, Inc. ENVIRONMENTAL REVIEW: Staff recommends the City Council find this action is not subject to the California Environmental Quality Act (CEQA) pursuant to Sections 15060(c)(2) (the activity will not result in a direct or reasonably foreseeable indirect physical change in the environment) and 15060(c)(3) (the activity is not a project as defined in Section 15378) of the CEQA Guidelines, California Code of Regulations, Title 14, Chapter 3, because it has no potential for resulting in physical change to the environment, directly or indirectly. Purchase of Rescue Ambulance April 12, 2016 Page 5 14-5 NOTICING: The agenda item has been noticed according to the Brown Act (72 hours in advance of the meeting at which the City Council considers the item). ATTACHMENTS: Attachment A – Purchase Agreement with Halcore Group, Inc., DBA Leader Industries Attachment B – Budget Amendment BA16-037 PURCHASE AGREEMENT FOR ONE (1)2016 FREIGHTLINER M2 EMERGENCY AMBULANCE MEDICAL VEHICLE FROM HALCORE GROUP,INC.,DBA LEADER INDUSTRIES This Purchase Agreement ("Agreement")is entered into as of this day of April,2016 ("Effective Date"),by and between the CITY OF NEWPORT BEACH, a California municipal corporation and charter city ("City"),and HALCORE GROUP,INC., DBA LEADER INDUSTRIES,an Indiana corporation ("Vendor"),whose principal place of business is 10941 Weaver Avenue,South El Monte,California 91733. RECITALS A. City is a municipal corporation duly organized and validly existing under the laws of the State of California with the power to carry on its business as it is now being conducted under the statutes of the State of California and the Charter of City. B. City requires one (1)2016 Freightliner M2 Emergency Ambulance Medical Vehicle ("Equipment")as further described in RFP No.16-24 which is attached hereto and incorporated herein by this reference as Exhibit A. C.Vendor has carefully reviewed and evaluated the specifications set forth by the City for the Equipment and has committed to deliver the Equipment required for the price specified in this Agreement within two hundred ten (210)calendar days commencing upon execution of this Agreement. D. City has solicited and received a proposal from Vendor's agent,has evaluated the expertise of Vendor,and desires to submit an order for the Equipment under the terms and conditions set forth in this Agreement. NOW,THEREFORE,in consideration of the mutual representations,warranties and covenants,and other terms and conditions as set forth herein,Vendor and City (each a "Party"and together the "Parties")agree as follows: 1.TERM The Term of this Agreement shall commence on the Effective Date and shall terminate on December 31,2016 unless terminated earlier as set forth herein. 2.COMPENSATION 2.1 City shall choose the purchase price as more fully described in the Pricing Proposal attached hereto as Exhibit B and incorporated herein by reference.The purchase price for Equipment,including all sales taxes,shall not exceed Two Hundred Sixty Six Thousand Seven Hundred Thirty Two Dollars and 19/100 ($266,732.19) ("Purchase Price"). ATTACHMENT A 14-6 3.ADMINISTRATION This Agreement will be administered by the City's Municipal Operations Department.The Deputy Municipal Operations Director,or designee,shall be the Purchase Administrator and shall have the authority to act for City under this Agreement.The Purchase Administrator or designee shall represent City in all matters pertaining to the services to be rendered pursuant to this Agreement. 4.DELIVERY 4.1 Delivery to City of the Equipment shall be made within two hundred ten (210)calendar days from the execution of the Agreement. 4.2 Delivery shall be made to the City's Corporate Yard at 592 Superior Avenue,Newport Beach,California 92663,or such other location as may be designated by City in writing.Time of delivery is of the essence in this Agreement.City reserves the right to refuse the Equipment,or part thereof,and to cancel all or any part of the Equipment not conforming to applicable specifications,samples or descriptions.City shall receive a pro-rata refund for the Equipment,or part thereof,cancelled under this Agreement,within thirty (30)calendar days of City's cancellation.Acceptance of any part of the order for Equipment shall not bind City to accept future shipments nor deprive City of the right to return Equipment already accepted at Vendor's expense. Over shipments and under shipments of Equipment shall be only as agreed to in writing by City.Delivery shall not be deemed to be complete until all Equipment have actually been received and accepted in writing by the City. 4.3 Vendor shall submit all requests for extensions of time for delivery in writing to the City Purchase Administrator not later than ten (10)calendar days after the start of the condition that purportedly causes a delay.The Purchase Administrator shall review all such requests and may, at his/her sole discretion,grant reasonable time extensions for unforeseeable delays that are beyond Vendor's control. 4.4 The Parties agree that it is extremely difficult and impractical to determine and fix the actual damages that City will sustain should the Vendor fail to complete the delivery as called for in this Agreement.Should Vendor fail to complete the delivery as called for in this Agreement,Vendor agrees to the deduction of liquidated damages in the sum of One Hundred Fifty Dollars and 00/100 ($150.00)per day,for every day beyond the date scheduled for delivery provided in Section 4.1.Execution of this Agreement shall constitute agreement by the City and Vendor that the sum of One Hundred Fifty Dollars and 00/100 ($150.00)per day,is the minimum value of costs and actual damages caused by the failure of Vendor to deliver the Equipment within the allotted time.All liquidated damages shall be paid within ten (10)calendar days of City's written request for payment.Such sum is liquidated damages and shall not be construed as a penalty,and may be deducted from payments due the Vendor,or recovered from Vendor,as applicable,if such delay occurs. Halcore Group,Inc., DBA Leader Industries Page 2 14-7 5.ACCEPTANCE/PAYMENT Unless otherwise agreed to in writing by City,acceptance of the Equipment shall not be deemed complete unless in writing and until all the Equipment,including each part thereof,has actually been received,inspected and tested to the satisfaction of City. 6.NOTICES 6.1 All notices,demands,requests or approvals to be given under the terms of this Agreement shall be given in writing,and conclusively shall be deemed served when delivered personally, or on the third business day after the deposit thereof in the United States mail,postage prepaid,first-class mail,addressed as hereinafter provided. 6.2 All notices,demands,requests or approvals from Vendor to City shall be addressed to City at: Attn:Deputy Municipal Operations Director Municipal Operations Department City of Newport Beach 100 Civic Center Drive PO Box 1768 Newport Beach,CA 92658 Phone:949-644-3059 Fax:949-650-0747 Email:mpisani(a)newportbeachca.qov 6.3 All notices,demands,requests or approvals from City to Vendor shall be addressed to Vendor at: Attn:Steve De La Montanya Leader Industries 10941 South Weaver Avenue South El Monte,CA 91733 7.TAXES The Purchase Price includes any and all applicable taxes and fees,including federal,state and/or local sales or use taxes.Under the City's Direct Payment Exemption permit number SF EAA 24-089475 DP, City shall self-accrue its Use Tax obligation to the California State Board of Equalization in the applicable amount within thirty (30)days of Equipment delivery to the City. Ifonly partial delivery of Equipment is received,the City will only pay the State Board of Equalization the amount of Use Tax due on the value of the Equipment delivered. 8.ENTIRE AGREEMENT This Agreement contains the entire Agreement between the Parties with respect to all matters herein,and there are no restrictions,promises,warranties,or undertakings other than those set forth herein or referred to herein. No exceptions, Halcore Group,Inc., DBA Leader Industries Page 3 14-8 alternatives,substitutes or revisions are valid or binding on City unless authorized by City in writing.Electronic acceptance of any additional terms,conditions or supplemental agreements by any City employee or agent,shall not be valid or binding on City unless accepted in writing by the Purchase Administrator.The terms of this Agreement shall supersede any inconsistencies between this Agreement and the Exhibits hereto. 9.WARRANTY 9.1 Vendor expressly warrants that the Equipment covered by this Agreement is: 1)free of liens or encumbrances;2) of merchantable quality and good for the ordinary purposes for which it is used;and 3) fit for the particular purpose for which it is intended.Acceptance of this Agreement shall constitute an agreement upon Vendor's part to indemnify,defend and hold City and its indemnities as identified in Section 15 below,and as more fully described in Section 15,harmless from liability,loss,damage and expense,including reasonable counsel fees,incurred or sustained by City by reason of the failure of the Equipment to conform to such warranties,faulty work performance,negligent or unlawful acts,and non-compliance with any applicable state or federal codes,ordinances,orders,or statutes,including the Occupational Safety and Health Act (OSHA)and the California Industrial Safety Act.Such remedies shall be in addition to any other remedies provided by law. 9.2 Vendor and manufacturer's warranties and certifications are attached hereto as Exhibit C,and incorporated in full by this reference.The Warranty Period shall commence on the date the Equipment is accepted by the City.All warranty repair work shall be conducted by a Vendor-certified dealer/agent in the Southern California region. 9.3 As of the Effective Date of this Agreement the Vendor-certified dealer/ agent for purposes of all repairs and warranty work is:Leader Industries,10941 Weaver Avenue,South El Monte,California 91733. 9.4 In the event that Vendor designates a different certified dealer/agent for the Southern California region,Vendor shall provide City with written notice of such change within ten (10)days of the change. 10.ASSIGNMENT OR SUBCONTRACTING The terms,covenants,and conditions contained herein shall apply to and bind the heirs,successors,executors,administrators and assigns of the Parties. Furthermore,neither the performance of this Agreement nor any portion thereof may be assigned or subcontracted by Vendor without the express written consent of City.Any attempt by Vendor to assign or subcontract the performance or any portion thereof of this Agreement without the express written consent of City shall be invalid and shall constitute a breach of this Agreement. Halcore Group,Inc., DBA Leader Industries Page 4 14-9 11.TERMINATION 11.1 In the event that either Party fails or refuses to perform any of the provisions of this Agreement at the time and in the manner required,that Party shall be deemed in default in the performance of this Agreement.If such default is not cured within a period of two (2)calendar days after receipt of written notice of default specifying the nature of such default and the steps necessary to cure such default,or if more than two (2)calendar days are reasonably required to cure the default and the defaulting Party fails to give adequate assurance of due performance within two (2) calendar days after receipt of written notice of default,or thereafter fails to diligently take steps to cure the default,the non-defaulting Party may terminate the Agreement forthwith by giving to the defaulting Party written notice thereof.City shall be refunded all money for Equipment not delivered and accepted by City at time of termination within thirty (30)calendar days.Cause for default shall further be defined as any breach of this Agreement,any misrepresentation or fraud on the part of the Vendor and/or filing of any petition in U.S.Bankruptcy Court or entering of Bankruptcy by Vendor. 11.2 Notwithstanding the above provisions,City shall have the right,at its sole discretion without cause,of terminating this Agreement at any time by giving seven (7) calendar days prior written notice to Vendor.In the event of termination under this Section,City shall pay Vendor for services satisfactorily performed and costs incurred up to the effective date of termination for which Vendor has not been previously paid. City shall be refunded all money for Equipment not delivered and accepted by City at time of termination within thirty (30)calendar days.On the effective date of termination, Vendor shall deliver to City all equipment,reports,documents and other information developed or accumulated in the performance of this Agreement,whether in draft or final form. 12.CONSENT TO BREACH NOT WAIVER No term or provision of this Agreement shall be deemed waived and no breach excused,unless such waiver or consent shall be in writing and signed by the Party claimed to have waived or consented to such breach.Any consent by any Party to,or waiver of, a breach by the other,whether express or implied,shall not constitute consent to,waiver of,or excuse for any other different or subsequent breach. 13.REMEDIES NOT EXCLUSIVE The remedies for breach set forth in this Agreement are cumulative as to one (1) another and as to any other provided by law,rather than exclusive;and the expression of certain remedies in this Agreement does not preclude resort by either Party to any other remedies provided by law. 14.PERFORMANCE AND FAITHFUL PERFORMANCE BOND 14.1 Vendor shall perform all work under this Agreement,taking necessary steps and precautions to perform the work to City's satisfaction.Vendor shall be responsible for the professional quality,technical assurance,timely completion and coordination of all documentation and other Equipment or services furnished by the Halcore Group,Inc.,DBA Leader Industries Page 5 14-10 Vendor under this Agreement.Vendor shall perform all work diligently,carefully,and in a good and workman-like manner;shall furnish all labor,supervision,machinery, equipment,materials,and supplies necessary therefore;shall at its sole expense obtain and maintain all permits and licenses required by public authorities,including those of City required in its governmental capacity,in connection with performance of the work; and,if permitted to subcontract,shall be fully responsible for all work performed by subcontractors. 14.2 Vendor shall obtain,provide and maintain at its own expense during the term of this Agreement a Faithful Performance Bond in the amount of one hundred percent (100%)of the Purchase Price to be paid Vendor as set forth in this Agreement. The form of such Faithful Performance Bond is attached as Exhibit E and incorporated herein by reference.The Faithful Performance Bond shall be issued by an insurance organization or surety (1)currently authorized by the Insurance Commissioner to transact business of insurance in the State of California,(2)listed as an acceptable surety in the latest revision of the Federal Register Circular 570,and (3)assigned a Policyholders'Rating A-(or higher)and Financial Size Category Class VII (or larger)in accordance with the latest edition of Best's Key Rating Guide:Property-Casualty. 14.3.Vendor shall deliver,concurrently with execution of this Agreement,the Faithful Performance Bond and a certified copy of the "Certificate of Authority"of the Insurer,or Surety issued by the Insurance Commissioner,which authorizes the Insurer or Surety to transact surety insurance in the State of California. 15.INDEMNIFICATION 15.1 To the fullest extent permitted by law,Vendor shall indemnify,defend and hold harmless City, its City Council,boards and commissions,officers,agents, volunteers,and employees (collectively,the "Indemnified Parties")from and against any and all claims (including,without limitation,claims for bodily injury,death or damage to property),demands,obligations,damages,actions,causes of action,suits,losses, judgments,fines,penalties,liabilities,costs and expenses (including,without limitation, attorney's fees,disbursements and court costs)of every kind and nature whatsoever (individually,a Claim;collectively,"Claims"),which may arise from or in any manner relate (directly or indirectly)to any breach of the terms and conditions of this Agreement,any work performed or services provided under this Agreement including, without limitation,defects in workmanship or materials (including the negligent and/or willful acts,errors and/or omissions of Vendor,its principals,officers,agents, employees,suppliers,consultants,subcontractors,anyone employed directly or indirectly by any of them or for whose acts they may be liable or any or all of them). 15.2 Notwithstanding the foregoing,nothing herein shall be construed to require Vendor to indemnify the Indemnified Parties from any Claim arising from the sole negligence or willful misconduct of the Indemnified Parties.Nothing in this indemnity shall be construed as authorizing any award of attorneys'fees in any action on or to enforce the terms of this Agreement.This indemnity shall apply to all claims and liability regardless of whether any insurance policies are applicable.The policy Halcore Group,Inc., DBA Leader Industries Page 6 14-11 limits do not act as a limitation upon the amount of indemnification to be provided by the Vendor. 16.CHARGES AND LIENS Vendor shall pay promptly all indebtedness for labor,materials and equipment used in performance of the work.Vendor shall not permit any lien or charge to attach to the Equipment,but if any does so attach,Vendor shall promptly procure its release and, in accordance with the requirements of Section 15 above,indemnify,defend,and hold City harmless and be responsible for payment of all costs,damages,penalties and expenses related to or arising from or related thereto. 17.INSURANCE Without limiting Vendor's indemnification of City,and prior to commencement of work,Vendor shall obtain,provide and maintain at its own expense during the term of this Agreement or for other periods as specified in this Agreement,policies of insurance of the type,amounts,terms and conditions described in the Insurance Requirements attached hereto as Exhibit D,and incorporated herein by reference. 18.CHANGE OF OWNERSHIP Vendor agrees that if there is a change or transfer in ownership of Vendor's business prior to completion of this Agreement,the new owners shall be required under terms of sale or other transfer to assume Vendor's duties and obligations contained in this Agreement and complete them to the satisfaction of City. 19.FORCE MAJEURE Vendor shall not be assessed with liquidated damages or unsatisfactory performance penalties during any delay beyond the time named for the performance of this Agreement caused by any act of God,war,civil disorder,employment strike or other cause beyond its reasonable control,provided that Vendor gives written notice of the cause of the delay to City within forty-eight (48)hours of the start of the delay and Vendor avails itself of any available remedies. 20.CONFIDENTIALITY Vendor agrees to maintain the confidentiality of all City and City-related records and information pursuant to all statutory laws relating to privacy and confidentiality that currently exist or exist at any time during the term of this Agreement.All such records and information shall be considered confidential and kept confidential by Vendor and Vendor's staff,agents,employees and subcontractors. 21.FREIGHT (F.O.B.DESTINATION) The Purchase Price includes shipment and delivery of Equipment to designated City location.Vendor assumes full responsibility for all transportation,transportation Halcore Group,Inc., DBA Leader Industries Page 7 14-12 scheduling,packing,handling,insurance,and other services associated with delivery of all products deemed necessary under this Agreement. 22.TERMS AND CONDITIONS Vendor acknowledges that it has read and agrees to all terms and conditions included in this Agreement. 23.SIGNATORIES AUTHORITY Each person executing this Agreement expressly warrants that he or she is authorized to do so on behalf of the entity for which he or she is executing this Agreement.The City and Vendor represent and warrant that this Agreement is executed voluntarily,with full knowledge of its significance. 24.STANDARD PROVISIONS 24.1 Recitals.City and Vendor acknowledge that the above Recitals are true and correct and are hereby incorporated by reference. 24.2 Compliance with all Laws.Vendor shall at its own cost and expense comply with all statutes,ordinances,regulations and requirements of all governmental entities,including federal,state,county or municipal,whether now in force or hereinafter enacted. 24.3 Integrated Contract.This Agreement represents the full and complete understanding of every kind or nature whatsoever between the Parties hereto,and all preliminary negotiations and Agreements of whatsoever kind or nature are merged herein.No verbal contract or implied covenant shall be held to vary the provisions herein. 24.4 Conflicts or Inconsistencies.In the event there are any conflicts or inconsistencies between this Agreement and the Exhibits attached hereto,the terms of this Agreement shall govern. 24.5 Amendments.This Agreement may be modified or amended only by a written document executed by both Vendor and City and approved as to form by the City Attorney. 24.6 Controlling Law and Venue.The laws of the State of California shall govern this Agreement and all matters relating to it and any action brought relating to this Agreement shall be adjudicated in a court of competent jurisdiction in the County of Orange,State of California.The California Commercial Code shall be the controlling law for the terms of this Agreement. 24.7 Equal Opportunity Employment.Vendor represents that it is an equal opportunity employer and it shall not discriminate against any subcontractor,employee or applicant for employment because of race,religion,color,national origin,handicap, ancestry,sex,age or any other impermissible basis under law. Halcore Group,Inc., DBA Leader Industries Page 8 14-13 24.8 Interpretation.The terms of this Agreement shall be construed in accordance with the meaning of the language used and shall not be construed for or against either Party by reason of the authorship of the Agreement or any other rule of construction which might otherwise apply. 24.9 Severability.If any term or portion of this Agreement is held to be invalid, illegal,or otherwise unenforceable by a court of competent jurisdiction,the remaining provisions of this Agreement shall continue in full force and effect. 24.10 No Attorneys'Fees.In the event of any dispute or legal action arising under this Agreement,the prevailing Party shall not be entitled to attorneys'fees. 24.11 Counterparts.This Agreement may be executed in two or more counterparts,each of which shall be deemed an original and all of which together shall constitute one and the same instrument. [SIGNATURES ON NEXT PAGE] Halcore Group,Inc., DBA Leader Industries Page 9 14-14 IN WITNESS WHEREOF,the Parties have caused this Agreement to be executed on the dates written below. APPROVED AS TO FORM: CITY ATTORNEY'S OFFICE :M////&Date CITY OF NEWPORT BEACH, a California municipal corporation and charter city Date: By: Aaron C.Harp City Attorney ATTEST: Date: 6\^c^/oWia-Diane B.Dixon Mayor CONTRACTOR:Halcore Group,Inc., DBA Leader Industries,an Indiana corporation Date: By:. Leilani I.Brown City Clerk Attachments:Exhibit A: Exhibit B Exhibit C Exhibit D Exhibit E By:. Gary Hunter President Date: By:. Sandra Stipe Director of Sales [END OF SIGNATURES] City of Newport Beach Specifications for Emergency Ambulance Medical Vehicle Pricing Proposal Warranty Insurance Requirements Faithful Performance Bond Halcore Group,Inc., DBA Leader Industries Page 10 14-15 EXHIBIT A CITY OF NEWPORT BEACH SPECIFICATIONS FOR AN EMERGENCY AMBULANCE MEDICAL VEHICLE Halcore Group,Inc.,DBA Leader Industries Page A-1 14-16 CITY OF NEWPORT BEACH REQUEST FOR PROPOSAL NO.16-24 (1)NEW,UNUSED EMERGENCY AMBULANCE MEDICAL VEHICLE PART 1:GENERAL BIDDER AND VEHICLE REQUIREMENTS 14-17 PART 1:GENERAL BIDDER AND VEHICLE REQUIREMENTS Instructions: Initial the bottom of each page of the Chassis Specifications in the space provided and remit as part of your Proposal,acknowledging a demonstrated understanding of the stated requirements.Any and all exceptions to the stated mandatory minimum requirements shall be indicated on the Statement of Compliance and identified by the Item Number listed in the specifications.Each specification must also be circled to note as compliant or not compliant.Failure to note compliance or to list exceptions shall result in your bid being deemed as non-responsive. Exceptions: The specifications listed herein may reflect a combination of ambulance units previously deployed by the City or those that are currently in the City's fleet.The line items are written to convey functionality that the City expects or has become accustomed to,not necessary those that will only be accepted by the City.The City's baseline for considering the functionality of a proposed unit will be that established by the KKK Federal Specifications for Ambulance Standards. Even if your proposed unit meets the federal standard for a specific line item in this specification but does not fully meet the line item as listed,this is still considered as an exception for purposes of this RFP and should be noted as such in the Statement of Compliance.However,during the evaluation process,the evaluation panel will be reviewing these exceptions closely to determine if they affect the overall technical functionality of the proposed unit.So long as your unit meets or exceeds the federal standard for a particular line item,the panel will evaluate and score your proposed unit accordingly,for each line item. ITEM NUMBER SPECIFICATIONS COMPLIANT? CIRCLE ONE 1.PROPOSAL COMPLETION PROCESS 1.1 Various areas in the following specifications require a response from the Bidder.In order to aid in the evaluation process all responses must be consistent and,most importantly,legible.©N 2.ENGINEERING SUPPORT Proposer Initials:c^sm City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 2 14-18 2.1 ***REQUIRED DOCUMENTATION***Due to the complexity of the design of the vehicle,proposals will be accepted only from manufacturers that utilize well-defined engineering techniques. Computer Aided Design (CAD)drawings of both the interior of the patient area and the overall layout of the module body will be mandatory.At a minimum these drawings shall include all exterior elevations,all interior views (4),and a plan view of the roof/ceiling.All options and elements required within these specifications shall be depicted on the prints.The purpose of this requirement is to assure this purchaser that vehicle proposals indeed meet the stated requirements as set forth in these specifications. Are the required drawings included with this Proposal? 0 N 3.MINIMUM VEHICLE REQUIRED STANDARDS 3.1 The highest degree of quality,both in the materials and in the building processes,is required for the emergency medical vehicle being proposed.At a minimum the manufacturer being proposed must meet all current mandated and voluntary ambulance design standards in effect at the date of the proposal submission.All current Federal Motor Vehicle Safety Standards (FMVSS)must be met. ©N 3.2 All electrical and mechanical equipment furnished shall comply with the California administrative Code;Title 8 (Industrial Safety Orders),Title 24 (State Building Standards Law)and Title 17 (Public Health).All electrical equipment furnished shall be grounded,with any exceptions only as approved in the referenced applicable titles. ©N 3.3 ***REQUIRED DOCUMENTATION***The body shall be capable of providing impact,deformation and penetration resistance in the event of a collision.The body structure shall be capable of passing a standalone static load test on a type tested body.The test shall be conducted in accordance to AMD-001 except the test weight shall be 55,000 pounds or 5.7 times the curb weight of the finished vehicle.(Over 3.8 times the test weight imposed by AMD-001).Additionally the same unit shall be subjected to the same test with the body turned on its side.Complete copy of the testing documents with photos,must accompany the 0 N Proposer Initials: City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 3 14-19 bid/proposal.Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards. Noncompliant proposals shall be rejected. Are the required testing documents included with this Proposal? 3.4 ***REQUIRED DOCUMENTATION***Safety is of the upmost importance to the purchaser.While currently there are no federal standards for crash testing an ambulance,the purchaser requires an outside third party test by a certified SAE facility to validate the structural crash worthiness of the ambulance conversion.The test will exceed the standards established by the National Highway Traffic Safety Administration and the Insurance Safety Institute for Highway Safety for side impact of a standard passenger sedan.To more accurately replicate the severity of a side impact collision on an ambulance the speeds should be boosted to 42 miles per hour.Complete copy of the testing documents with photos,must accompany the bid/proposal.Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards. Noncompliant bids will be rejected. Are the required testing documents included with this Proposal? ©N 3.5 Bidder shall keep records of parts used in the manufacture of the specified equipment and shall notify the buyer of any improvement or modifications that may improve the specified equipment. ©N 3.6 ***REQUIRED DOCUMENTATION***The manufacturer shall comply with Ford Motor Company's QVM program.A copy of the manufacturer's current QVM certification must be submitted with the Proposal. Is the current Ford QVM certification included with this Proposal? 0 N 3.7 ***REQUIRED DOCUMENTATION***The manufacturer shall comply with Sprinter ambulance converter requirements.A copy of the manufacturers'current Sprinter Ambulance converter ©N Proposer Initials:efl2J3& City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 4 14-20 certification must be submitted with the bid. Is the current Sprinter certification included with this Proposal? 3.8 ***REQUIRED DOCUMENTATION***The Vendor shall include with their bid a copy of their California Automobile Dealers License. Is a copy of the California Automobile Dealer's License included with this Proposal? 0 N 3.9 ***REQUIRED DOCUMENTATION***The Proposer submitting this Proposal shall include with their bid a copy of their California Vehicle Sale Person License. Is a copy of the California Vehicle Sale Person License included with this Proposal? ©N 4.LIABILITY 4.1 The bidder shall defend,indemnify,and save harmless the purchaser and its officials from all claims,demands,payments, suits,actions,recoveries,and judgments of every description, whether or not well founded in law,brought or recovered against it, by reason of any act or omission of said bidder,his agents or employees,in the execution of the contract or in consequence of insufficient protection or for the use of any patented invention by said bidder,and a sum sufficient to cover aforesaid claims may be retained by the purchaser from money due or to become due to the bidder under this contract,until such claims have been discharged or satisfactorily secured. ©N 4.2 ***REQUIRED DOCUMENTATION***Each bidder must furnish a Certificate of Insurance showing aggregate total of insurance, which shall not be less than twenty-five million dollars ($25,000,000). Is a Certificate of Insurance included with this Proposal? 0 N 4.3 In addition,the bidder is to assume any risk of loss to the ambulance until the ambulance is delivered to this purchaser.©N Proposer Initials:SD£Wl City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 5 14-21 Does the bidder understand this requirement? 5.PRE-CONSTRUCTION CONFERENCE 5.1 A pre-construction conference will be held at the successful bidders manufacturing facility by 2 Department representatives within 14 days of award of bid. A trip requiring travel of more than 200 miles shall be via commercial air carrier and shall include transportation,room,and board for 3 day/2 night stay. Number of personnel:_2 Are these Pre-Construction trips included in this proposal? 0 N 6.MID-CONSTRUCTION CONFERENCE 6.1 A Mid-Construction conference will be held at the successful bidders manufacturing facility by 2 Department representatives after the body is painted and mounted to the chassis,but prior to the install of wiring or cabinets.This is to confirm that the module configuration is compliant and that paint color and finish are to specifications.Final build detail will be reviewed at this time.A trip requiring travel of more than 200 miles shall be via commercial air carrier and shall include transportation,room, and board for 3 day/2 night stay. Number of personnel:_2 Are these Pre-Construction trips included in this proposal? ©N 7.FINAL VEHICLE INSPECTION 7.1 Vehicle will be inspected for compliance with these specifications by 2 Department representatives of the City at the manufacturing facility prior to delivery.It will be the responsibility of the Dealer to ask for inspection when vehicle is ready for delivery.The burden of proof of compliance with this specification will be the responsibility of the bidder.A trip requiring travel of more than 200 miles shall be via commercial air carrier and shall include transportation,room,and board for 3 day/2 night stay. ©N Proposer Initials:spj?m, City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 6 14-22 Number of personnel:_2 Are these Pre-Construction trips included in this proposal? 8.VEHICLE DELIVERY 8.1 The vehicle shall be delivered over the road,or via rail-line to the purchaser.©N 8.2 The vehicle will be delivered cleaned fueled with a full tank of diesel and in as new condition.0 N 8.3 Mileage on delivered unit shall not exceed 200 miles in excess of manufactures final assembly plant if delivered over the road to the purchaser. ©N Proposer Initials:S?D£Wt City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 7 14-23 CITY OF NEWPORT BEACH REQUEST FOR PROPOSAL NO.16-24 (1)NEW,UNUSED EMERGENCY AMBULANCE MEDICAL VEHICLE PART 2:CHASSIS SPECIFICATIONS City of Newport Beach RFPNo.16-24 Page 8 Emergency Ambulance Medical Vehicle 14-24 PART 2:CHASSIS SPECIFICATIONS Instructions: Initial the bottom of each page of the Chassis Specifications in the space provided and remit as part of your Proposal,acknowledging a demonstrated understanding of the stated requirements.Any and all exceptions to the stated mandatory minimum requirements shall be indicated on the Statement of Compliance and identified by the Item Number listed in the specifications.Each specification must also be circled to note as compliant or not compliant.Failure to note compliance or to list exceptions shall result in your bid being deemed as non-responsive. The chassis required for this project is specified in detail below.Failure of the bidder to provide the chassis exactly as specified will be grounds for rejection of the bidder's proposal as being non-responsive.Exceptions will be made only if the bidder can prove that a required feature is unavailable from the chassis O.E.M.The acronym O.E.M. Is Original Equipment Manufacturer.The O.E.M. is the chassis manufacturer and the vehicles Make Origin. Exceptions: The specifications listed herein may reflect a combination of ambulance units previously deployed by the City or those that are currently in the City's fleet.The line items are written to convey functionality that the City expects or has become accustomed to, not necessary those that will only be accepted by the City.The City's baseline for considering the functionality of a proposed unit will be that established by the KKK Federal Specifications for Ambulance Standards. Even if your proposed unit meets the federal standard for a specific line item in this specification but does not fully meet the line item as listed,this is still considered as an exception for purposes of this RFP and should be noted as such in the Statement of Compliance.However,during the evaluation process,the evaluation panel will be reviewing these exceptions closely to determine if they affect the overall technical functionality of the proposed unit.So long as your unit meets or exceeds the federal standard for a particular line item,the panel will evaluate and score your proposed unit accordingly,for each line item. ITEM NUMBER SPECIFICATIONS COMPLIANT? CIRCLE ONE 9.CHASSIS 9.1 Chassis:2016 FREIGHTLINER M2 106 CONVENTIONAL 0 N Proposer Initials:ST)£Mt Cityof Newport Beach RFP No. 16-24 Page 9 Emergency Ambulance Medical Vehicle 14-25 CHASSIS: The vehicle converter shall supply a 2016 or newer 174.00" wheelbase,108.45 Cab Axle,63.00 Axle to Frame:Freightliner chassis for the ambulance conversion.The wheelbase shall be factory supplied by the O.E.M.Modified wheelbases made from chassis with shorter or longer wheelbases are not acceptable. 10.AMBULANCE CHASSIS PROFILE 10.1 THE PACKAGE SHALL BE DESIGNED TO HOLD UP TO THE DEMANDS AND DUTY CYCLES INHERENT WITH EMERGENCY MEDICAL VEHICLES. 0 N 10.2 REQUESTED GVWR:22,000.O N 10.3 DIMENSION:Wheelbase:174.00,CA:108.45,axle to frame: 63.00 O N 10.4 ENGINE,DIESEL:CUM ISB 6.7-280,280 HP @ 2300 RPM, 2600 GOV,660 LB/FT @ 1600 RPM O N 10.5 REGEN INHIBIT SPEED THRESHOLD - 5 MPH 6 N 10.6 TRANSMISSION,AUTOMATIC:Allison 2200 EVS Automatic Transmission With Park Pawl,Inc.PTO Provision O N 10.7 AXLE,FRONT:Non-Driving Detroit Da-F-10.0-3 10,000#Ffl 71.5 Kpi/3.74 Drop Single Front Axle. Axle,REAR:Detroit Da-Rs-17.5-2 17,500#R-Series Single Rear Axle. 0 N 10.8 CAB:CONVENTIONAL O N 10.9 TIRE,FRONT:(2)225/70r19.5 G647 RSS (Goodyear)640 Rev/Mile,Load Range F,12 Ply O N 10.10 TIRE,REAR: (4)225/70M9.5 G622RSD (Goodyear)641 Rev/Mile,Load Range F,12 Ply O N 10.11 SUSPENSION,REAR: Air,Single Liquid Spring Conversion; 12,000-Lb Capacity. Exceptions to this requirement will be considered, provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 9 N 10.12 PAINT:One Solid Color,High Solids Polyurethane Chassis Paint O N 11.ENGINE AND RELATED EQUIPMENT 11.1 ENGINE PERFORMANCE:Shall comply with or exceed the O N Proposer Initials:SVJ3K City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 10 14-26 most current revision of kkk-a-1822 11.2 ENGINE,CUM ISB 6.7-280 280 HP @ 2300 RPM,2600 GOV, 660 LB/FT @ 1600 RPM O N 11.3 2015 ONBOARD DIAGNOSTICS/2010 EPA/CARB/GHG14 2008 CARB EMISSION CERTIFICATION -EXEMPTED VEHICLE;NO CLEAN IDLE LABEL REQUIRED 0 N 11.4 Engine Mounted Oil Check and Fill O N 11.5 Side Of Hood Air Intake with Firewall Mounted Donaldson Air Cleaner ©N 11.8 Cummins Turbocharged 18.7 CFM Air Compressor with Internal Safety Valve,Mechanical Air Compressor Governor 0 N 11.9 Cummins Exhaust Brake Integral With Variable Geometry Turbo With On/Off Dash Switch,Activates Stop Lamps 0 N 11.10 Engine After Treatment Device,Automatic Over The Road Active Regeneration and Dash Mounted Single Regeneration Request/Inhibit Switch ©N 11.11 6 Gallon Diesel Exhaust Fluid Tank (Y)N 11.12 Horton HT650 Frontal Air On/Off Engine Fan Clutch,or equivalent ©N 11.13 Automatic Fan Control With Dash Switch And Indicator Light, Non Engine Mounted ©N 11.14 Cummins Spin On Fuel Filter,Full Flow Oil Filter O N 11.15 950 Square Inch Aluminum Radiator,O N 11.16 Antifreeze To -34f,Ethylene Glycol Pre-Charged SCA Heavy Duty Coolant ©N 11.17 Gates Blue Stripe Coolant Hoses Or Equivalent 0 N 11.18 Constant Tension Hose Clamps For Coolant Hoses ©N Proposer Initials:<?pj?w. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 11 14-27 11.19 Radiator Drain Valve O N 11.20 PHILLIPS-TEMRO 750 Watt/115 Volt Block Heater,or equivalent 0 N 11.21 Chrome Engine Heater Receptacle Mounted Under LH Door 0 N 11.22 Aluminum or Cast Iron Flywheel Housing 0 N 11.23 Electric Grid Air Intake Warmer 0 N 11.24 DELCO 12v 38MT HD Starter With Integrated Magnetic Switch 0 N 12.TRANSMISSION EQUIPMENT 12.1 ALLISON 2200 EVS Automatic Transmission With Park Pawl With PTO Provision O N 12.2 ALLISON Vocational Package 364 -Available On 1000/2000 Product Families with Vocational Model EVS,Allison Vocational Rating for Fire Truck/Emergency Vehicle Applications Available with all Product Families 0 N 12.3 Primary Mode Gears,5 Forward Gears With Manual Selection For 3,2 And 1. 0 N 12.4 Dash Mounted T-Handle Cable Shift Control With Park Position For Internal Park Pawl. 0 N 12.5 Magnetic Plugs,Engine Drain,Transmission Drain,Axle(S)Fill and Drain 0 N 12.6 Synthetic Transmission Fluid (TES-295 Compliant)0 N 12.7 Water To Oil Transmission Cooler,In Radiator End Tank ©N 12.8 Electronic Transmission Customer Access Connector Firewall Mounted 0 N 13.FRONT AXLE AND EQUIPMENT 13.1 Detroit Da-F-10.0-3 10,000#FF1 71.5 KPI/3.74 Drop Single Front Axle,or equivalent ©N 13.2 Meritor 15X5 Q+Cast Spider Cam Front Brakes,Double Anchor,Fabricated Shoes,or equivalent ©N 13.3 Fire And Emergency Severe Service,Non-Asbestos Front Lining ©N Proposer Initials:<zdj?w. City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 12 14-28 13.4 CONMET Cast Iron Front Brake Drums,or equivalent 0 N 13.5 SKF SCOTSEAL PLUS XL Front Oil Seals,or equivalent 0 N 13.6 Vented Front Hub Caps With Window,Center And Side Plugs - Oil ©N 13.7 HALDEX Automatic Front Slack Adjusters,or equivalent ©N 13.8 TRW THP-60 Power Steering,or equivalent 0 N 13.9 Organic SAE 80/90 Front Axle Lube 0 N 13.10 2 Quart See Through Power Steering Reservoir 0 N 14.FRONT SUSPENSION 14.1 10,000#Taperleaf Front Suspension 0 N 14.2 Maintenance Free Rubber Bushings -Front Suspension 0 N 14.3 Front Swaybar 0 N 14.4 Front Shock Absorbers 0 N 15.REAR AXLE AND EQUIPMENT 15.1 Detroit DA-RS-17.5-2 17,500#R-Series Single Rear Axle,or equivalent ©N 15.2 4.10 Rear Axle Ratio 0 N 15.3 MXL 16T Meritor Extended Lube Main Driveline With Half Round Yokes,or equivalent ©N 15.4 Meritor 15x8.62 Q+Cast Spider Cam Rear Brakes,Double Anchor,Fabricated Shoes,or equivalent ©N 15.5 Fire And Emergency Severe Service Non-Asbestos Rear Brake Lining ©N 15.6 Brake Cams And Chambers On Forward Side Of Drive Axle(S) With Auxiliary Support Brackets ©N Proposer Initials:crp/mf City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 13 14-29 15.7 CONMET Cast Iron Rear Brake Drums,or equivalent 0 N 15.8 Rear Oil Seals 0 N 15.9 HALDEX GOLDSEAL LONGSTROKE 1-Drive Axle Spring Parking Chambers,or equivalent ©N 15.10 HALDEX Automatic Rear Slack Adjusters,or equivalent 0 N 15.11 Organic SAE 80/90 Rear Axle Lube 0 N 16.REAR SUSPENSION 16.1 Airliner 12,000#Rear Suspension,Airliner Mid Position Ride Height,or equivalent ©N 16.2 Ignition Controlled Electric Dump Switch For Air Suspension With Autofill Override Valve ©N 16.3 10,000/15,000#Airliner Rear Suspension Stabilizer Bar,or equivalent ©N 16.4 Rear Shock Absorbers -One Axle (Air Ride Suspension)0 N 17.BRAKE SYSTEM 17.1 Air Brake Package 0 N 17.2 Wabco 4S/4M ABS Without Traction Control 0 N 17.3 Reinforced Nylon,Fabric Braid And Wire Braid Chassis Air Lines ©N 17.4 BW AD-9SI Brake Line Air Dryer With Heater 0 N 17.5 Air Dryer Mounted Under Hood 0 N 17.6 Steel Air Brake Reservoirs Mounted Inside Rail 0 N 17.7 BW DV-2 Auto Drain Valve Without Heater On All Tank(0 N 18.WHEELBASE &FRAME Proposer Initials:SDJffl. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 14 14-30 18.1 4425mm (174 Inch)Wheelbase 0 N 18.2 CALC'D Back Of Cab To Rear Suspension Center Line (CA): 108.45 In ©N 18.3 1600mm (63 Inch)Rear Frame Overhang 0 N 19.CHASSIS EQUIPMENT 19.1 Three-Piece 14 Inch Chromed Steel Bumper with Collapsible Ends 0 N 19.2 Front Tow Hooks -Frame Mounted ©N 19.3 Fender and Front Of Hood Mounted Front Mud flaps 0 N 20.FUEL TANKS 20.1 34 Gallon/128 Liter Short Rectangular Aluminum Fuel Tank - LH,or equivalent 0 N 20.2 Rectangular Fuel Tank,or equivalent ©N 20.3 Alliance Fuel Filter/Water Separator With Primer Pump 0 N 20.4 EQUIFLO Inboard Fuel System,or equivalent 0 N 20.5 High Temperature Reinforced Nylon Fuel Line 0 N 21.TIRES/WHEELS 21.1 MICHELIN XZE 245/70M9.5 16 Ply Radial Front Tires 0 N 21.2 MICHELIN XDS2 245/70M9.5 16 Ply Radial Rear Tires 0 N 21.3 ALCOA 77362X 19.5X7.50 10-Hub Pilot 5.23 Inset Aluminum Disc Front Wheels,Polished Front Wheels;Outside Only ©N 21.4 ALCOA 77362X 19.5X7.50 10-Hub Pilot Aluminum Disc Rear Wheels,Polished Rear Wheels;Outside Of Outer Wheels Only ©N 21.5 FORCEMATCH Tire/Wheel Runout Check/Mark and Static Balancing - All Tires/Wheels ©N 22.CAB EXTERIOR Proposer Initials:SV&tt City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 15 14-31 22.1 22.2 22.3 22.4 22.5 22.6 22.7 22.8 22.9 22.10 22.11 22.12 22.13 22.14 23.1 23.2 24.1 24.2 24.3 24.4 24.5 106 Inch BBC Flat Roof Aluminum Conventional Cab Rubber Cab Mounts Fiberglass Hood Hood Mounted Chromed Plastic Grille,Chrome Hood Mounted Air Intake Grille Dual 25 Inch Round Stutter Tone Hood Mounted Air Horns With Dual Lanyards Dual Electric Horns,Dual Horn Shields Door Locks and Ignition Switch Keyed The Same Integral Headlight/Marker Assembly With Chrome Bezel Led Aerodynamic Marker Lights Headlights On With Wipers,With Daytime Running Lights RH and LH Electric Powered Windows,Passenger Switches On Doors Tinted Door Glass LH and Rh With Tinted Operating Wing Windows LH And Rh Exterior Grab Handles With Single Rubber Insert 2 Gallon Windshield Washer Reservoir Without Fluid Level Indicator,Frame Mounted 23.MIRRORS Dual West Coast Bright Finish Heated Mirrors With LH and RH Remote LH and RH 8 Inch Bright Finish Convex Mirrors Mounted Under Primary Mirrors 24.INTERIOR CAB TRIM (PREMIUM) Cab Interior Color:The Color of the Cab Interior Shall Be Gray.All Conversion Manufacturers'Added Consoles and Devices Shall Be Color Keyed To The Interior Color Provided By The O.E.M. Opal Gray Vinyl Interior Premium Insulation Black Mats with Single Insulation Molded Door Panel With Upper Vinyl Inserts Proposer Initials:SVJT/K. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle © © © © ia © © © © 0 N N N N N N N_ N N N N N N N N N N N N_ N Page 16 14-32 24.6 Forward Roof Mounted Console With Upper Storage Compartments and Additional Center Compartment without Netting. ©N 24.7 In Dash Storage Bin 0 N 24.8 Gray/Charcoal Flat Dash 0 N 24.9 Smart Switch Expansion Module 0 N 24.10 Solid-State Circuit Protection And Fuses 0 N 24.11 Dome Door Activated LH and Rh,Dual Reading Lights, Forward Cab Roof ©N 24.12 LH and RH Electric Door Lock Switches (y)N 24.13 (1)12 Volt Power Supply In Dash m N 24.15 LH and RH Integral Door Panel Armrests 0 N 24.16 Adjustable Tilt And Telescoping Steering Column 0 N 24.17 4-Spoke 18 Inch (450mm)Steering Wheel N 24.18 Driver and Passenger Interior Sun Visors ©N 25.AIR CONDITIONING 25.1 Heater,Defroster and Air Conditioner,Standard HVAC Ducting ©N 25.2 Main HVAC Controls with Recirculation Switch ©N 25.3 Air Conditioning:Dual Compressor System;(1)Denso Heavy Duty and (1)Sanden Compact Refrigerant Compressor.©N 26.CAB SEATS:DRIVER/PASSENGER/OEM CAPTAIN'S CHAIRS 26.1 Premium High Back Air Suspension Driver Seat With 3 Chamber Air Lumbar,Integrated Cushion Extension,Forward and Rear Cushion Tilt,Adjustable Shock Absorber,Vinyl With Cloth Insert,Arm Rest Right Side ©N 26.2 Premium High Back Air Suspension Passenger Seat With 3 Chamber Air Lumbar,Integrated Cushion Extension,Forward and Rear Cushion Tilt,Adjustable Shock Absorber Vinyl With Cloth Insert,Arm Rest Left Side. ©N 26.3 3 Point High Visibility Orange Retractor Driver and Passenger Seat Belts ©N 27.INSTRUMENTS &CONTROLS 27.1 Engine Remote Interface with Park Brake And Neutral Interlocks ©N Proposer Initials:syjtM City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 17 14-33 27.2 2 Inch Primary and Secondary Air Pressure Gauges.©N 27.3 Dash Mounted Air Restriction Indicator With Graduations 0 N 27.4 Electronic Cruise Control With Switches In LH Switch Panel ©N 27.5 Key Operated Ignition Switch and Integral Start Position; 4 Position Off/Run/Start/Accessory 0 N 27.6 Icu3s,132x48 Display With Diagnostics,28 Led Warning Lamps and Data Linked,Diagnostic Interface Connector,9 Pin,SAE J1939,Located Below Dash 0 N 27.7 2 Inch Electric Fuel Gauge ©N 27.8 Engine Remote Interface with Preset Fast Idle ©N 27.9 Electrical Engine Coolant Temperature Gauge ft N 27.10 Engine and Trip Hour Meters Integral within Driver Display ©N 27.11 Electric Engine Oil Pressure Gauge ©N 27.12 Electronic MPH Speedometer With Secondary KPH Scale, Without Odometer ©N 27.13 Standard Vehicle Speed Sensor Q N 27.14 Electronic 3000 Rpm Tachometer u)N 27.15 Ignition Switch Controlled Engine Stop (Y)N 27.16 AM/FM/WB Radio with Cd Player,Bluetooth and Microphone, USB,Front and Rear Auxiliary Inputs and J1939,(2)Radio Speakers In Cab ©N 27.17 Single Electric Windshield Wiper Motor With Delay Q N 27.18 Marker Light Switch Integral with Headlight Switch (y)N 27.19 One Valve Parking Brake System with Warning Indicator ©N 27.20 Self Canceling Turn Signal Switch With Dimmer, Washer/Wiper and Hazard In Handle ©N 27.21 Integral Electronic Turn Signal Flasher with Hazard Lamps Overriding Stop Lamps ©N 28.CHARGING/BATTERIES 28.1 BATTERY SYSTEM:Maintenance-Free,(3)12-Volt Group 31- 3,000 CCA TotalThe vehicle shall be equipped with Four (4) {International}Maintenance-Free OEM batteries ©N 28.2 JUMP START STUDS:Remote Mounted,Positive and negative posts.©N Proposer Initials:SDJffK City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 18 14-34 28.3 BATTER DISCONNECT SWITCH [Joseph Pollack 51-315] Positive Type,Lever Operated,Cab Mounted ©N 28.1 ALTERNATOR:{Leece-Neville 14931 PAH}Brush Type,12 Volt 320 Amp.Capacity,Pad Mounted ©N 29.WARRANTY 29.1 The chassis manufacturer's standard vehicle warranty policies shall apply ©N 30.DOCUMENTATION 30.1 In addition to the standard chassis and conversion Operators Manuals,a complete set of Chassis,Engine,and Transmission Shop manuals on CD or DVD.Will be provided and shipped loose with the vehicle ©N CHASSIS HARDWARE AND ACCESSORIES The items to follow represent chassis modifications,hardware,and accessories that are required.Failure to provide these features will be cause for rejection of the bidder's proposal as being non-responsive 31.CHASSIS TO MODULAR PASS-THROUGH 31.1 The chassis cab shall be modified by the successful bidder to allow for passage between the cab and the patient compartment.The required opening shall be cut out of the back of the cab.A flexible weather-tight Hypalon bellows shall be installed around the perimeter of the opening between the back of the cab and the front of the module body.All of the work required under this section shall be performed by the successful bidder.The work shall not be performed by a third party vendor.This shall guarantee a consistent level of quality and warranty protection while assuring that the work is engineered specifically for use with the module body and other equipment as specified ©N 32.CAB STEP WELL/RUNNING BOARDS 32.1 Diamond plate step well covers shall be installed on both the curb side and street side cab step wells.The covers shall be ©N Proposer Initials:sDjm. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 19 14-35 made of .125"thick polished diamond tread plate with a minimum 3003-H14 alloy.Each Step cover will provide a minimum of two steps for entry into the cab. 33.WHEEL HUB AND LUG NUT COVERS 33.1 Phoenix,Polished S/S Hub and Nut Covers.The center steel hub and lugs shall be capped off with bright stainless steel, snap on caps designed to cover wrench marks,normally left on the lug nuts.The design shall not affect tire and wheel balance when the vehicle is driven between zero and eighty miles per hour ©N 34.MUD FLAPS,REAR 34.1 The vehicle converter shall install individual rubber mud flaps behind each rear wheel.The mud flaps may incorporate the converter's corporate logo provided that the logo is made out of stainless steel or equivalent and attached to the mud flap. Logos either printed on, or otherwise incorporated into the mud flap are not desirable as they cannot be removed and possess a tendency to fade ©N 35.REAR STEP/BUMPER ASSEMBLY 35.1 REAR STEP/BUMPER ASSEMBLY:The rear of the vehicle shall be equipped with a step/bumper..Bumper will be mounted to chassis by means of a sub frame fabricated from .250"(minimum)steel tube and plate.Sub frame will bolt to chassis frame via a minimum of four (4)14"diameter Grade 8 fasteners. The distance between the top of the step and the ground shall not be less than 16 inches. ©N 35.2 The center section of the bumper will include a 60"W X 9- 1/2"D,.125"Star punched aluminum bolt-in insert.Insert will be mounted below rear entry doors,and braced to frame.The distance between the ground and the top of this step will be not less than 16 inches.Center section will be hinged to accommodate Cot loading. ©N Proposer Initials:SZ>£7H. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 20 14-36 35.3 Bumper ends will be fixed,and fabricated from .125"bright aluminum treadplate.Bumper ends will be "radiused,"or "cornered"approximately 45 degrees on each side. ©N 35.4 The distance between the top of the step and the ground shall not be less than 16 0 N 36.DOC BUMPERS 36.1 Black rubber pods 16" long x 2.5" tall x 2"deep O N 36.2 Each rubber docking bumper shall be fastened through each bumper end cap to the supporting .250"steel frame by three (3) 3/8"grade 8 fasteners ©N 37.REAR TOW HOOKS 37.1 Each tow hook shall be made from forged steel with a minimum capacity of ten thousand pounds (10,000)and mounted to the bumper frame by two (2)1/2"grade 8 bolts ©N 38.REVERSE ALARM 38.1 An audible alarm shall be installed to activate when the vehicle is placed into reverse gear ©N 38.2 There shall be,installed on the front console and wired through the vehicle electrical system,a momentary cutoff switch to disable the alarm.This switch shall automatically reset each time the vehicle is placed into reverse gear ©N 39.CONVERTER-PROVIDED BATTERIES 39.1 One (1)Converter added battery will be provided CD N 39.2 The vehicle shall also be equipped with three (3) OEM batteries 0 N 39.3 All four (4)batteries will be located under the curbside forward compartment on a roll-out tray ©N 40.EMERGENCY START SYSTEM 40.1 The emergency start batteries may be used to start the vehicle W N Proposer Initials:$VJM City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 21 14-37 41.1 by utilizing a switch on the console to tie together all four batteries.If the system for emergency purposes is tied together a notification will appear on the master display 41.SPARE TIRE STORAGE Include mounted spare tire on matching wheel Proposer Initials:SV£M City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle C>N Page 22 14-38 CITY OF NEWPORT BEACH REQUEST FOR PROPOSAL NO.16-24 (1) NEW, UNUSED EMERGENCY AMBULANCE MEDICAL VEHICLE PART 3:AMBULANCE MODULE SPECIFICATIONS Proposer Initials:ST>£tK City of Newport Beach RFP No.16-24 Page 23 Emergency Ambulance Medical Vehicle 14-39 PART 3:AMBULANCE MODULE SPECIFICATIONS Instructions: Initial the bottom of each page of the Ambulance Module Specifications in the space provided and remit as part of your Proposal,acknowledging a demonstrated understanding of the stated requirements.Any and all exceptions to the stated mandatory minimum requirements shall be indicated on the Statement of Compliance and identified by the Item Number listed in the specifications.Each specification must also be circled to note as compliant or not compliant.Failure to note compliance or to list exceptions shall result in your bid being deemed as non-responsive. Exceptions: The specifications listed herein may reflect a combination of ambulance units previously deployed by the City or those that are currently in the City's fleet.The line items are written to convey functionality that the City expects or has become accustomed to,not necessary those that will only be accepted by the City.The City's baseline for considering the functionality of a proposed unit will be that established by the KKK Federal Specifications for Ambulance Standards. Even if your proposed unit meets the federal standard for a specific line item in this specification but does not fully meet the line item as listed,this is still considered as an exception for purposes of this RFP and should be noted as such in the Statement of Compliance.However,during the evaluation process,the evaluation panel will be reviewing these exceptions closely to determine if they affect the overall technical functionality of the proposed unit.So long as your unit meets or exceeds the federal standard for a particular line item,the panel will evaluate and score your proposed unit accordingly,for each line item. ITEM NUMBER SPECIFICATIONS COMPLIANT? CIRCLE ONE BASE SECTION The following section describes the required body design,manufacturing process,and materials.Adherence to this section is of extreme importance to this purchaser due to space requirements and safety concerns.The bidder must meet this section as closely as possible without utilizing experimental or prototype designs in order to be considered for bid award. 42.DIMENSIONS (THE COMPLETED VEHICLE SHALL HAVE THE FOLLOWING MINIMUM DIMENSIONS): 42.1 (Exterior Module)&N Proposer Initials:Sft^Wt City of Newport Beach RFP No.16-24 Page 24 Emergency Ambulance Medical Vehicle 14-40 -Height:92.5" -Width:95" -Length:173" 42.2 (Interior Module) -Height:72" -Aisle 46" -Length:168.5" ©N 42.3 OVERALL DIMENSIONS (Including Chassis,Module and Step) -Height:108" -Width:98" -Length:298" ©N 43.MODULAR BODY STRUCTURAL DESIGN REQUIREMENT"S 43.1 The module body shall be designed and fabricated with the following key elements in mind: 1.The greatest possible load carrying capacity is desired; 2.The safety of all vehicle occupants is of paramount concern; 3.The body design,including construction materials and fabrication techniques shall be proven to be durable. 4.The body shall be easily retrofitted to a new chassis should that need ever a rise. ©N 44.GENERAL BODY DESCRIPTION 44.1 SERVICE INTENT:The ambulance body shall be all aluminum. The body sheet shall be reinforced with structural members designed to resist deflection and hold up to extreme ambulance service per current revision of Federal specification KKK-A-1822 ©N 44.2 BODY MEMBER ALLOY:The side,roof,front and rear sheet shall be derived from 5052-H-32 Aluminum sheet.The roof sheet shall be one piece,from roof rail to roof rail.Preferred,but other options may be considered.The side structure and structural shapes shall be extruded of 6063-T6 aluminum. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards. ©N Proposer Initials:SV£ttt City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 25 14-41 44.3 BODY WARRANTY:The body shall carry a 15-year warranty following the date of delivery to the end user.The warranty shall cover repairs or replacement of body elements or components that fail due to structural defects in materials and workmanship 0 N 44.4 The body shall be re-mountable to a future new chassis,of exact specification,without voiding the 15-year body warranty, provided the remount is done by the Original Ambulance manufacturer or its authorized agency. ©N 45.PAYLOAD REQUIREMENTS 45.1 The vehicle payload shall meet or exceed that called for in the current KKK-A-1822 specification.Before delivery of the completed unit the manufacturer shall weigh the vehicle.This purchaser reserves the right to have the finished vehicle weighed independently upon delivery.It should be noted that this purchaser,while interested in attaining the greatest possible payload,is unwilling to compromise on the structural requirements of a strong,durable,and safe body.All bidders must understand these factors supersede concern over payload, and that the lightest body (greatest payload)will not necessarily be deemed sufficient to meet the stringent quality and safety requirements set forth herein. ©N 46.MODULE BODY STRUCTURAL INTEGRITY 46.1 The body structure shall be capable of passing a standalone static load test on a type-tested body.The test shall be conducted in accordance to AMD-001,or federal standards. A copy of the documents signed by a third party agency to conform to ISO 17020 and 17025,must accompany the bid/proposal. ©N 46.2 Safety is of the upmost importance to the purchaser.In addition to the static load testing required in LKK 1822-E ,The body structure shall be capable of meeting the standards defined in: AMD 002 -Body Door Retention Components Test AMD 003 -Oxygen Tank Retention System Static Test ©N Proposer Initials:SDj^M City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 26 14-42 AMD 004 -Liter Retention AMD 004 -Patient Compartment Grab Rail Static Load Test. The unit will also comply to the standards set forth in NFPA 1917-13 for the below listed items. 6.3 -Structural Integrity -Roof Loading 6.4 -Structural Integrity -Side Loading 6.8 -Handrail Testing 6.9 -Patient Compartment entry doors 6.13.7 -Body Floor Structural integrity 6.22 -Patient Cot Retention 6.28.10 -Oxygen tank Retention A copy of the documents signed by a third party agency to conform to ISO 17020 and 17025,must accompany the bid/proposal. 46.3 WELD QUALITY: All welds within the modular body shall meet American Welding Society codes for structural and sheet welding. ©N 46.4 CREVICE PREPARATION:All skin and extrusion surfaces destined to be mated shall be primed with chromate,etching primer prior to assembly.Additionally,all over lapping extrusion to skin surfaces shall be bedded with a one part polyurethane adhesive sealant. ©N 46.5 PRECISION BUILD:This specification requires that the module body,including all doors,be built within a tolerance of one five- thousandths of one inch.To achieve this the vehicle manufacturer must use,as standard practice,precision computerized equipment such as found in Strippet machines and microprocessor controlled milling machines and chop saws. Use of precision equipment will ensure that all door openings, door handles and latches,body windows,and warning light assembly installation locations are of the correct size and square ©N Proposer Initials:SDjOTK. City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 27 14-43 to the body. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards. 47.SIDE STRUCTURAL MEMBERS 47.1 CORNER POST SUPPORTS:The body structure must be able to support the loaded weight of the vehicle in the unlikely event of a rollover.A one-piece 90-degree radius post is required.The posts shall include a full length W shaped extrusion that forms a fully encased web inside the post for strength.This reinforcing member shall angle inward just before it joins the radius to form a small slot where the edges of the aluminum skin will be inserted prior to the final welding. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 47.2 CORNER POST STRENGTH:The corner post extrusions shall possess a minimum ultimate tensile strength of 27,000 psi (6063-T5). Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 47.3 WALL AND ROOF SKIN SUPPORTS:The exterior wall and roof skins shall be supported on the inside by 2"square tubing with .125"wall.These structural supports shall be strategically located at the load bearing points of the module body.The roof structural support beams shall be spaced on minimum 12" centers for adequate load support.Wall tubing of .125"thickness or less will not be acceptable. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 47.4 SKIN TO SUPPORT ATTACHMENT: All exterior aluminum body panels shall be attached to the underlying structural supports via high performance polyurethane two sided tape.The tape shall have a polyurethane ©N Proposer Initials:SV£)K. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 28 14-44 foam core for environmental resistance and an acrylic adhesive for a durable bond.The tape will be used as an insulating agent to hold the panels tightly against the structural supports,thus eliminating vibration and oil-canning.In addition to the tape attachment system,all panels shall be welded to structural members at the perimeters only.Welding in the center of the panels is not desired as the process will cause heat distortion of the body panels and lessen the overall quality of the finished appearance. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 47.5 SKIN TO SUPPORT ATTACHMENT (PART 2):Each body panel shall be welded to all horizontal frame members,including the roof extrusions.In addition,the panels shall be welded to the vertical corner posts.In the case of the roof,the perimeter of the one-piece roof sheet shall be welded.This method of attachment shall provide a total welding application to the entire perimeter of the body skin and a taped/insulating application to the interior surfaces of all walls. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 47.6 GUSSET ENHANCEMENT:Gusset supports,made from 2" square tubing,shall be installed throughout the vehicle for added strength.Each gusset shall be a minimum of 5" long at its longest point. A minimum of twenty-four (24) of these gussets shall be welded into the vehicle support structure.Areas of installation shall include but not be limited to: all door openings, all body corners,and above all wheel wells. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 48.BODY SHEET 48.1 EXTERIOR BODY PANELS:The materials selected for the body skin have been chosen because of this vehicles expected heavy-duty cycle and the good wear characteristics that this ©N Proposer Initials:SQJ2& City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 29 14-45 material has shown in the field.The material shall be a minimum 0.125"5052-H34 alloy with an ultimate tensile strength of 38,000 psi. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 49.SEAT BELT ANCHORAGE 49.1 Occupant seat belts shall be through bolted through one-half by four inch plates that are continuously M.I.G.Welded to the structural grid. The Attachments will comply to current SAE standards. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 0 N 50.ROOF CONSTRUCTION 50.1 PERIMETER EXTRUSIONS:A double hollow extrusion shall provide a structural transition between the module walls and the roof assembly.The shape shall incorporate a full perimeter drip rail. An anti-torsion web shall also be incorporated to enhance the bend resistance of the shape.The alloy shall be 6063-T6 Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 50.2 ROOF SHEET:The roof sheet shall be a one piece,seamless, .090 thick,5052-H32 aluminum.The four edges of the sheet shall be continuously bonded to the roof rail extrusion to prevent leaks.All perimeter welds shall be ground smooth and worked smooth prior to the overall paint job. Note:The roof shall incorporate a 3/8"crown designed to allow water to drain. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N Proposer Initials:SV^W. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 30 14-46 50.3 ROOF BOWS:The roof sheet shall be supported by full width .125 wall x 2" x 2"architectural box tubing.The roof bows shall be located on twelve inch centers.The roof bows shall be M.I.G. Welded to the roof rail extrusions with no less than four and one- half inches of continuous weld per end.The roof sheet shall be bonded to the roof bows with VHB (Very High Bond)adhesive tape. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 50.4 ROOF CORNERS:The roof rail extrusions shall be welded together along the roof bow mating walls at the corners.In addition,the outer surfaces of the roof rail extrusions shall be continuously M.I.G.Welded to cast aluminum corner castings. The castings shall have rail shaped heat risers behind the weld sites to interlock the joint. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 51.FLOOR CONSTRUCTION 51.1 FLOOR MEMBERS:All Floor structures shall be a minimum of one-quarter (0.125)by two by three inch aluminum,6063-T6, architectural rectangular tubing. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 51.2 FULL WIDTH CROSS MEMBERS:The module floor shall provide core support for the side assemblies.The floor, from the front to the rear and from curbside to street side shall be supported by a minimum 2" x 3"tubular beams with a .25" wall. The floor just behind the axle shall be supported by a minimum 1.5"x 3"tubular beam with a .25"wall.All beams shall be strategically located at the load bearing points of the floor and welded into place. Exceptions to this requirement will be considered,provided ©N Proposer Initials:sV£7tt City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 31 14-47 the exceptions meet minimum KKK Federal Specifications for Ambulances standards 51.3 COT MOUNT:One-half inch (1/2")thick plates shall be welded into the floor structure assembly at all locations where cot fasteners or seating will be installed.All hardware shall be through bolted whenever possible.One inch (1")thick tapping plates shall be welded in at all locations where through bolting cannot be accomplished,such as over fuel tanks Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N COT MOUNT REINFORCEMENT PLATES:Power Load Additional under floor reinforcement is required for future installation of a Stryker Power Load system. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 51.4 WATER TIGHT PATIENT CABIN:A .090"thick aluminum sub sheet shall be welded,and sealed to the floor structure with silicone sealant.Additional aluminum plates shall be intermittent welded between compartments,wheel well liners,step wells and fuel filler housings.All of the areas shall be thoroughly sealed from one to the other,creating a sealed patient cabin from the outside. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 51.5 The sub floor,above the aluminum sheet noted above,shall consist of ZA"marine grade plywood.There shall be a minimum of pockets or voids at the floor to the sidewalk areas where water or moisture can become trapped or cause unsanitary conditions.All voids and pockets shall be filled with a sealer or caulking compound to provide a 100%smooth finish from floor to wall.The floor bottom shall be completely sealed to prevent moisture and toxic fumes from entering the patient compartment. ©N Proposer Initials:SV^M City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 32 14-48 52.1 53.1 Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 52.MOUNTING SYSTEM The OEM chassis manufacturer determines the outside dimension,across the frame rails on this chassis.A minimum of (5) five Mounting platforms shall be attached along the outside of each chassis frame rail for a total of (10)ten.Each platform shall consist of (1)top plate of .375"thick steel and (2)side reinforcement plates made of .25"steel.There shall be a .375" full backing plate where the mount attaches to the frame rail. The plates shall be welded along all seams with a heavy continuous weld.The body substructure shall include a .5" by .3" solid aluminum tie down bar welded to each substructure cross member.To complete the body to chassis attachment,a dull isolation tuned mounting system shall be used. The elastomer mount shall be custom-tuned to the specific chassis type for vibration reduction,structure borne noise attenuation and to provide low profile,low frequency isolation necessary for ideal patient compartment conditions.Standard chassis furnished mounting donuts will not meet the requirements of this specification. The Isolation Mount shall be attached to each platform by (2) .625"Grade 8 bolts with washers and locking nuts.The platform shall be attached to the chassis frame rail with a minimum of (3) .625"diameter Grade 8 bolts with washers and locking nuts.The failsafe elastomer isolation mount shall then attach to the aluminum body tie down bar with a .75"diameter Grade 8 bolt, a washer,and a locking nut. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 53.CURBSIDE ENTRY DOOR CURB SIDE ACCESS DOOR:The curbside access door shall be at least 84 13/16"high by 31"wide measured at the doorjamb © opening Proposer Initials:SVJtM Cityof Newport Beach RFP No. 16-24 Emergency Ambulance Medical Vehicle ©N N Page 33 14-49 53.2 STEP WELL: A curbside entry door shall feature a two-step "step well" to assist in patient cabin egress.The steps shall have a tread dimension of not less than 9 inches.The riser dimension shall not exceed 10 inches,measured from the step tread to the floor of the patient cabin.A right-angled trim,made of polished Stainless Steel,shall be formed over the flooring material and wrap around the 3-sided perimeter of the step well. Step well material shall be 0.100 thick,Polished aluminum diamond plate.The step well shall be illuminated by a GROTE Brand LED light.The light will be activated by the side entry door.The step well shall meet or exceed the current revision of Federal specification KKK-A-1822. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 54.REAR ENTRY DOORS 54.1 REAR ACCESS DOORS:The rear of the module shall be equipped with double seamless patient compartment access doors.The doors shall be centered on the body and align with the patient compartment aisle space.The doors shall measure 46 3/4 inches wide by 56 5/8" high,jamb to jamb ©N 54.2 REAR ACCESS DOOR JAMB:At the rear access doors,a full width,formed seamless stainless steel jamb protection plate shall be provided to prevent the cot frames from chipping the paint.The stainless steel protection package shall start from under the kick plate and follow the contour of the outer jamb and convert to a 45 degree entry transition ramp as it enters the door opening and covers the end of the sub-floor.The sill is to extend onto the module floor and cover the last six inches of the vinyl floor covering ©N 55.COMPARTMENT CONSTRUCTION 55.1 MATERIALS:Unless specified otherwise,all exterior compartment walls and backs shall be constructed of .125 polished aluminum diamond plate.All compartment floors shall be formed of .125 aluminum sheet.Compartments for Generators,Oxygen,and Backboards will have .250 compartment floors.All compartment ceilings shall be formed of .125 aluminum sheet.The ceilings and floors shall form around ©N Proposer Initials:SVSW- City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 34 14-50 the sides and back to provide an overlapping joint.The floor and ceiling surfaces shall be double action (DA)sanded to 180 grit. The floors and ceilings are bonded to the walls and back and intermittent welded on six (6) inch center. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 55.2 VENTILATION:All compartments,made from aluminum sheet, shall have at least eight louvers of ventilation to the outside.All compartments shall be louvered through an interior sidewall with at least nine (9)square inches of free-vented area.An exterior splash shield will be provided to prevent water and to minimize the intrusion of dust to the interior of the compartment. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 55.3 DRAIN HOLES:Drainage holes shall be provided on the bottom of non sweep out compartments.Each hole shall be baffled to prevent splash water from entering the compartment. ©N 55.4 ADJUSTABLE SHELF:When a shelf is specified a standard duty aluminum adjustable shelf shall be provided.The shelf shall be formed of .125 (1/8") thick polished aluminum diamond plate, with 2 inch upward turned lips on all four sides. ©N 55.5 SHELF MOUNTING:When a shelf is specified unit strut track will be installed.The Unistrut channel shall be made from 1 5/8" x 13/16 " x 16 gauge 6063-T6 extruded aluminum.The channel shall be plug welded vertically through the outside of the compartment body, with a minimum of five (5)Vz diameter welds per each channel. The channel nuts shall be made of case hardened steel with %"- 20 threads and spring loaded to prevent slipping while being adjusted. The shelf mounting bracket shall be made of cast aluminum with a brite finish.The casting size shall be 2" x 2" x 2"and a minimum of 1/8"thick. Exceptions to this requirement will be considered,provided ©N Proposer Initials:SV^M City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 35 14-51 the exceptions meet minimum KKK Federal Specifications for Ambulances standards 55.6 SURFACE PROTECTION:All exterior compartments shall have black rubber matting on compartment bottoms,shelves and slide-out trays ©N 55.7 COMPARTMENT LIGHTING: LED strip lighting in all exterior compartments. (2)per compartment. Location:Inside compartment door frames.Run full height on both sides. The lights will come on when the door is opened 0 N 56.DOOR CONSTRUCTION 56.1 DOOR SKIN:The door skin shall be .125 thick 5052-H34 aluminum sheet formed on all four sides to create a crevice free surface for best paint adhesion and corrosion resistance.The formed edges shall not have elongation cracks due to forming. The formed edges uniformly rounds off exposed edges for better paint adhesion and aesthetic appeal.The Skin will not be formed into the door frames. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 56.2 DOOR FRAMING:The door frame shall reinforce the perimeter of the skin pan.The extrusion shall incorporate a T-slot to receive an extruded,hollow,closed cell weather strip.The door frame shall also add torsion resistance to the door assembly. The door frame shall be mitered at the corners,assembled with one-way,drive-in splines,and continuously welded on the inside.The doorframe shall also incorporate a clearance way for UNF threaded blind fasteners for the door panels. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 56.3 FINAL DOOR ASSEMBLY:The door skin shall be bonded to the frame assembly with an adhesive sealant in addition to intermittent welding.Additional adhesive sealant shall be applied to the inside of the door skin to prevent moisture from becoming ©N Proposer Initials:SVJZM City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 36 14-52 trapped between the skin and the door frame extrusion.For entry doors:Additional,horizontal structure shall be added to maintain door skin flatness as well as penetration resistance in the event of a collision.The C-shaped,horizontal members shall be formed from one hundred twenty five mils thick aluminum sheet.A minimum of two.horizontal members shall be welded in. A vertically oriented c-channel shall be welded to the webs of both horizontal channels for additional buckling resistance. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 56.4 CORNER SPLINES:Both the door frame and the door jambs will be constructed of extruded aluminum 6063-T6.The extruded shapes shall be designed to mate together.There shall be a corner spline located in each corner of both the door frame and jamb.The corner spline shall be a solid milled aluminum shape that when in place creates a perfect ninety (90)degree corner. The spline shall completely fill the hollow cavity of the door frame and jamb extrusions.The spline shall be slightly larger than the cavity of the extrusions so that it must be driven into place.The spline shall have four (4)barb style wedges that prevent the spline from being removed once it is driven into place.The splines shall be approximately one half inch thick by one inch wide by four inches long (.5" x 1" x 4") in both directions from the ninety degree corner.Modular bodies that do not use both extruded door frames and jambs,nor bodies that do not use drive-in splines are not acceptable. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 56.5 DOOR PANELS:The inside door panels shall be made of not less than 100 mills (0.100)thick aluminum plate.The edges of the door panel shall be recessed into the door frame extrusion. The panels shall be fastened to the door frame with stainless steel,#10-32 UNF machine screws threaded into aircraft quality blind fasteners.Each screw shall have an internal tooth lock washer to preclude loosening. Exceptions to this requirement will be considered,provided ©N Proposer Initials:crpjntf City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 37 14-53 the exceptions meet minimum KKK Federal Specifications for Ambulances standards 56.6 DOOR JAMB:The doorjamb shall accommodate rigid fastening of compartment door hinges.The jamb shall include a hollow cell that shall conceal wiring for the non-mechanical door switch. The doorjamb corners shall be mitered and have drive-in corner spines to hold the door square and rigidly together at the corners.Additionally,the jamb shall be continuously M.I.G. Welded on the inside and the outside corners.The door frames will have a visible flange on the exterior of the body.This allows for replacement of the door and compartment jamb without disassembly of the module body. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 56.7 HINGE:All doors shall have stainless steel,continuous,piano hinge.The pin diameter shall be .250 and staked into place to prevent drifting out of the hinge leaf.The knuckle lengths shall be one inch.The hinge attachment bolts shall be one quarter inch diameter,twenty threads per inch by one inch long stainless steel Type F hex head bolts.All tapped holes for hinge bolts shall be treated with an anticorrosion compound prior to installation of each hinge bolt.Each hinge leaf shall have a Mylar insulation strip between the leaf and the Jamb/Door. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 56.8 LATCHES:The latches shall meet FMVSS 206.All latches shall be two-stage,rotary-type.The latches shall be through bolted to the doorframe extrusion. All entry doors shall have two rotary latches per door.To assure uniform latch timing and functional door reliability, only straight, one-quarter inch diameter rods shall connect the latches to the handle.Bends in door latch rods are NOT acceptable.Bends in door rods will straighten at undefined rates and cause latch timing problems.Unless otherwise specified herein,all single hung compartment doors shall have one rotary latch.All double hung compartment doors shall have two rotary latches per door. ©N Proposer Initials:SVJW. City of Newport Beach RFP No.16-24 Page 38 Emergency Ambulance Medical Vehicle 14-54 All striker pins shall be headed to prevent the door(s)from opening under impact. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 56.9 EXTERIOR HANDLES:The entire exterior handle assembly shall be Tri/Mark Series 2100 cast metal that is chrome plated and buffed to a high luster.Blind fasteners shall be used to fasten the handles to the door.Every paddle handle shall have an isolation gasket between the paddle body and the door skin. All door skin surfaces shall be painted prior to installation of the hardware.All paddles,on single hung and leading double doors shall be locking type and keyed the same.Trailing doors shall; have non-locking paddle handles,mounted on the outside of the door.The Handle shall have a bright chrome like finish mounted into a bright chrome coated dish. The latching mechanism will incorporate a free floating handle design Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 56.10 INTERIOR HANDLES:The interior handle shall be lever type.A Lock/Unlock lever shall be installed below the inside lever handle and be clearly marked Lock/Unlock ©N 57.HOLD-OPEN DEVICES 57.1 The following door hold-open devices shall be installed: Compartment doors:Gas filled,100-degree extension actuator. Side access door:Gas filled,110-degree extension actuator. Spring-loaded devices are not desired because of their weaker holding capabilities and a lack of smooth door operation ©N 57.2 DOOR SWING:The compartment door checks shall be installed to allow the door to open ninety degrees (90) from the fully closed position.Unless noted in a specific compartment ©N Proposer Initials:SDJtM City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 39 14-55 description. 57.3 REAR ACCESS DOOR CHECKS:Rear access doors shall open at least 150 degrees.The door checks shall be 2 piece, heavy duty,cast aluminum,grabber type with gaskets.The door shall have a 1/4 round stock loop that plunges into a positive rubber/cast socket ©N 58.WINDOWS,MODULE BODY ENTRY DOORS 58.1 REAR ENTRY DOOR WINDOW:The two rear doors shall feature a window with fixed glass.Each of these windows shall measure 16.5"h x 17"w and shall be glazed and tinted in accordance with FMVSS.The windows shall be encased in extruded aluminum frames.Under no circumstances will RV style windows,windows that rely on rubber gaskets,windows that do not feature extruded aluminum frames,or windows that do not meet the above stated minimum dimensions be acceptable. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 58.2 SIDE ENTRY DOOR WINDOW:The side access door shall feature a slidinq window.The window shall measure 16.5"h x 17"w and shall be glazed and tinted in accordance with FMVSS. The window shall be encased in extruded aluminum frames. Under no circumstances will RV style windows,windows that rely on rubber gaskets,windows that do not feature extruded aluminum frames,or windows that do not meet the above stated minimum dimensions be acceptable. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 59.PRIVACY GLASS 59.1 All of the patient area windows,as specified above,shall feature a dark 'privacy'tint.This tint shall be incorporated into the glass. This process is required over those utilizing laminates or films due to the tendency of such materials to peel or bubble over ©N Proposer Initials:ST>J!M Cityof Newport Beach RFP No. 16-24 Emergency Ambulance Medical Vehicle Page 40 14-56 time 60.INSULATION 60.1 The patient area of the vehicle shall be insulated with 2" of Owens Corning Quiet R,glass fibers bating,providing fire resistant,fungi &bacteria resistance,for both thermal and acoustic insulation.The compartment and access doors shall be fully lined with polydamp intefoam extensional damping pad for thermal and acoustical insulation.The duct work for the heating and air conditioning system shall be lined with .250 inch rigid foil back polystyrene insulation ©N 61.SOUNDPROOFING 61.1 To insure good working conditions and to create a stable patient environment,the vehicle shall be manufactured with particular attention paid to sound control.The following process must be performed throughout the manufacturing cycle of the vehicle: 1.Door interiors are to be lined with polydamp intefoam extensional damping pad 2. All walls shall be insulated with 2" of Owens Corning Quiet R, glass fibers bating acoustic insulation. 3.Headliners shall be double insulated with 2 Owens Corning Quiet R,glass fibers bating and a Reflectix barrier ©N 62.MODULE CONFIGURATION 62.1 MODULE LENGTH:The interior module length shall be at least one hundred sixty eight inches ©N 62.2 MODULE WIDTH:The module width shall comply with current revision of Federal Specification KKK-A-1822.The module shall be ninety five inches wide,excluding lights and accessories ©N 62.3 MODULE HEAD ROOM:The module shall not be less than Seventy Two inches actual measured headroom.The measurement shall be taken from the patient compartment floor to the ceiling panels ©N 62.4 LOAD HEIGHT:Load height is defined as the vertical measurement from the level ground to the finished floor plane. The load height specified herein shall not exceed the current ©N Proposer Initials:£Z)j*7K. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 41 14-57 Federal specification KKK-A-1822 63.LEFT FRONT COMPARTMENT 63.1 This compartment shall be located in the left front corner of the modular body. The minimum compartment dimensions shall be: Actual Dimensions:71.25"High x 22"Wide x 20.5"Deep Clear Door Opening:18.7"Wide x 70.5"High ©N 63.2 COMPARTMENT DOOR: A single,outside,forward hinged door shall be set for this compartment.The door shall have a single handle and two rotary latches.The compartment shall house the vehicle's primary 02 cylinder.The compartment shall be vented to the outside. ©N 63.3 COMPARTMENT FLOOR CONFIGURATION:Due to the stress transmitted to the floor of this compartment as a normal part of the loading and unloading of the main 02 cylinders the floor of this compartment will made of .250" flat plate Aluminum.This compartment floor shall be a sweep out type floor.The compartment floor shall be flush with the lower door jamb to facilitate compartment floor cleaning.The edge of the compartment floor shall be continuously welded to the lower door jamb.Heat generated from welding shall not distort the straightness or flatness of the jamb or compartment floor.The weld quality must be aesthetically uniform ©N 63.4 MAIN 02'MOUNTING HARDWARE:Standard Zico Mount ©N 63.5 FIXED VERTICAL DIVIDER:A fixed vertical divider will be located 8" to the right of the left hand wall in the compartment. The divider will be full height X 18"deep and made of .125 Aluminum plate ©N 63.6 ADJUSTABLE SHELF. A single,adjustable shelf will be located above the main 02 to the right of the fixed divider in this compartment.All exterior compartment shelves shall be constructed of .125 polished aluminum diamond plate ©N 63.7 DROP PAN FLOOR:Install a 4"drop pan in the 8"wide forward section to accommodate 72" tall Miller board storage forward of the divider ©N Proposer Initials:<?DJ7?f. Cityof Newport Beach RFP No. 16-24 Emergency Ambulance Medical Vehicle Page 42 14-58 63.8 STRAP SET:Provide and install a 1"strap set with quick release clip. Locate:Mid level from the front wall to the center divider 0 N 63.9 COMPARTMENT DOOR SILL PROTECTION:Install Stainless Steel protection plates on lower edge of exterior compartment.©N 64.LEFT INTERMEDIATE COMPARTMENT 64.1 This compartment shall be located in the right of the left front compartment. The minimum compartment dimensions shall be: Actual Dimensions:43"High x 55.5"Wide x 20.5"Deep Clear Door Opening:51.8"Wide x 41.3"High ©N 64.2 COMPARTMENT DOOR:A pair of outside,forward hinged, compartment doors shall be set for this compartment.The doors shall each have a single handle and one rotary latch ©N 64.3 COMPARTMENT FLOOR:This compartment shall feature a Two inch (2")dropped floor.The edge of the compartment shall be continuously welded to the lower doorjamb ©N 64.4 ADJUSTABLE SHELF.Two (2),adjustable shelves will be distributed in this compartment. Locate:The Lower shelf is to be set just above the battery storage area. Locate:Center the second shelf in the space above. All exterior compartment shelves shall be constructed of .125 polished aluminum diamond plate ©N 64.5 BATTERY STORAGE:FABRICATE AND INSTALL ROLL-OUT BATTERY TRAY ON 150-300LB ACCURIDE SLIDES. Note:SIZE FOR 4 BATTERIES. Locate:In the forward portion of the Streetside intermediate compartment at floor level. Locate:The Inverter/charger on the floor rearward of the battery tray. Note:Lower the standard shelf to just above the battery area to provide protection. ©N 64.6 COMPARTMENT DOOR SILL PROTECTION:Install Stainless Steel protection plates on lower edge of exterior compartment.©N Proposer Initials:SVJtM City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 43 14-59 65.LEFT REAR COMPARTMENT 65.1 This compartment shall be located in the left rear corner of the body. The minimum compartment dimensions shall be: Actual Dimensions:66.5"High x 37.4"Wide x 20.5"Deep. Clear Door Opening:32"Wide x 63.5"High The Upper 24.5"section above 42"will be 14"deep. 6.5"deep Interior cabinets will back to the portion of the compartment. This compartment has been designated for SCBA and Safety equipment storage. ©N 65.2 COMPARTMENT DOORS:A pair of outside,forward hinged, compartment doors shall be set for this compartment.The doors shall each have a single handle and one rotary latch. ©N 65.3 COMPARTMENT FLOOR:This compartment shall feature a Three inch (2")dropped floor.The edge of the compartment shall be continuously welded to the lower doorjamb ©N 65.4 ADJUSTABLE SHELF:Two (2)adjustable shelves will be located in this compartment. Location:Distribute in the full depth lower section. All exterior compartment shelves shall be constructed of .125 polished aluminum diamond plate ©N 65.5 TOOL MOUNTING PLATE: Install a pair of Unistrut style shelf track on the back wall,upper 24.5"portion. Bolt a .250"brushed aluminum plate on the Unistrut track. This will be used for install of SCBA hardware ©N 65.6 CUSTOM DOOR HOLD OPEN MOUNTS:The door hold opens are to be positioned to allow the doors to open over center providing access to the full compartment opening ©N 65.7 COMPARTMENT DOOR SILL PROTECTION:Install Stainless Steel protection plates on lower edge of exterior compartment.©N 66.RIGHT REAR BACKBOARD COMPARTMENT Proposer Initials:SD£ffl, City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 44 14-60 66.1 This compartment shall be located in the right rear comer of the module body.The minimum jamb pass through dimensions shall be: Actual Dimensions:29.6"Wide x 83.6"High x 20.5"Deep Clear Door Opening:25.1"Wide x 80.7"High ©N 66.2 COMPARTMENT DOOR:A single outside,forward hinged, compartment door shall be set for this compartment.The door shall have a single handle and two rotary latches. ©N 66.3 COMPARTMENT FLOOR CONFIGURATION:Due to the stress transmitted to the floor of this compartment as a normal part of the loading and unloading of back boards and the stair chair the floor of this compartment will made of .250"flat plate Aluminum. This compartment floor shall be a sweep out type floor.The compartment floor shall be flush with the lower door jamb to facilitate compartment floor cleaning.The edge of the compartment floor shall be continuously welded to the lower door jamb.Heat generated from welding shall not distort the straightness or flatness of the jamb or compartment floor.The weld quality must be aesthetically uniform. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 0 N 66.4 FIXED VERTICAL DIVIDER: Quantity:Two (2) A fixed vertical divider will be located 8' to the right of the left wall in the compartment.. The divider will be full height x 18"deep and made of .125 Aluminum plate. A second 40"tall divider will be located 9.5"to the right of the full height fixed divider ©N 66.5 FIXED SHELF:The bottom shelf will be located to the right of the full height fixed divider 40"above floor level to accommodate ©N Proposer Initials:ST)£tti City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 45 14-61 the storage of a stair chair and Auto Pulse below. 66.6 ADJUSTABLE SHELF:Two (2),adjustable shelves will be located to the right of the full height divider and distributed above the fixed shelf. All exterior compartment shelves shall be constructed of .125 polished aluminum diamond plate ©N 66.7 COMPARTMENT DOOR SILL PROTECTION:Install Stainless Steel protection plates on lower edge of exterior compartment.©N 67.CURBSIDE FRONT COMPARTMENT 67.1 This compartment shall be located in the right front corner of the body.The minimum compartment dimensions shall be Actual Dimensions:26.7"Wide x 83.6"High X 30"Deep Clear Door Opening:22.1"Wide x 79.1"High This area shall be accessed through a single outside,hinged door and from an opening located on the curb side forward wall (vehicle interior front wall area). This compartment shall be primarily used for storage of customer furnished jump kits. ©N 67.2 COMPARTMENT DOOR:A single,forward hinged, compartment door shall be set for this compartment.The door shall have a single handle and one rotary latch ©N 67.3 COMPARTMENT FLOOR:This compartment shall feature a Three inch (2")dropped floor.The edge of the compartment shall be continuously welded to the lower doorjamb. ©N 67.4 CUSTOM MODIFICATION TO SHELVING CONFIGURATION: Do not extend the module floor into the bulkhead cabinet.0 N 67.5 CUSTOM MODIFICATION TO DOOR HOLD OPEN SYSTEM: Curbside Forward Compartment,delete gas strut hold open,and replace with a Cast Products hold open device. Door is to open as far as possible without conflicting with the cab passenger door. ©N 67.6 COMPARTMENT DOOR SILL PROTECTION:Install Stainless Steel protection plates on lower edge of exterior compartment.©N BODY PROTECTION AND BRIGHT WORK Proposer Initials:SD£7K City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 46 14-62 68.MODULE BODY CORNER PROTECTION 68.1 The lower seventeen inches (17") of the corner post extrusions shall be protected against stones and road debris.The corner post guards shall be formed of .080 thick polished aluminum diamond plate,contour fit to the corner post extrusions and riveted into place.A bead of silver colored,silicone sealant shall be applied across the top edge of the guards.The bottom of edge of the guard shall be left unsealed to promote moisture drainage. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 69.FRONT STONE GUARDS 69.1 The front of the body shall have skirt-line protection plates made of polished Stainless Steel.The corner posts shall have form fit diamond plate protection height matched to the front body stone guards.The height of the protection is seventeen inches up from the body skirt line ©N 70.REAR KICK PLATE 70.1 The rear kick plate shall be made of 0.100 inch thick polished aluminum diamond plate and run from corner post to corner post.The height shall be from the skirt-line of the body to the bottom doorjamb under the rear access doors ©N 71.REAR FENDERS 71.1 The rear fenders shall be made of polished Aluminum.The mounting fasteners shall be Stainless Steel bolts with 100% nylon nut inserts.The fastener centers shall not exceed ten (10) inches ©N 72.SKIRT RUB RAILS 72.1 The entire skirt-line of the body,forward and aft on the rear wheels shall have formed Polished Aluminum "U"channel skirt rails to protect the body.Each skirt rail shall meet current Federal Specification KKK-A-1822.Each rail shall be chamfered 45 degrees at both ends.The rails shall not cut into the paint.They shall be mounted to the lower part of the ©N Proposer Initials:sVJDft City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 47 14-63 modular body in such a way that they are spaced off the body. INTERIOR 73.CABINETS 73.1 All cabinets shall be constructed of plywood.The plywood shall have a minimum of seven plies and all plies shall be made with hardwood type woods.Plywood's constructed of softwoods like fir or pine is not acceptable.The face of cabinet modules shall be one piece of plywood with the compartment openings routed out for strength.A high impact,phenolic backed,high impact, and abrasion resistant high pressure laminate shall be used on both sides of the plywood.Gator-ply or Kraft type paper backers are not acceptable due to potential moisture absorption, which can result in cabinets warping or absorption of blood born pathogens.This material as well as all interior components shall meet or exceed F.M.V.S.S.#302.The laminate shall be adhered to the plywood prior to cutting and routing to maximize the bond and minimize edge chipping.The glue shall be a PVA (poly vinyl acetate)and each piece shall be put in a glue press for a minimum 90 minutes at 30 pounds per square foot. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 73.2 Cabinets shall be assembled utilizing three construction methods;gluing,stapling and screwing.The length of the fastener shall be at least 2.25 times the thickness of the material being pierced through.Screw heads shall be counter-sink type and driven flush.Staples shall be placed on two-inch intervals along the joints.Where ever possible joints shall be tongue and groove.The glue used shall be yellow colored waterproof resin type ©N 73.3 Each cabinet shall be designed and constructed as an independent modular component.Partial cabinets are not acceptable because it reduces overall structural integrity. Cabinets shall be bolted to the body structure.Cabinets that are welded or otherwise permanently affixed to the module body structure will be unacceptable.Such permanent installation methods limit the ability to make design updates at a later time. They also increase the time and cost involved with regard to ©N Proposer Initials:SV^M City of Newport Beach RFP No.16-24 Page 48 Emergency Ambulance Medical Vehicle 14-64 remounting the body onto a new chassis should that occasion ever arise.Likewise,cabinets mounted with the use of either rivets or adhesives of any kind will not be considered without exception. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 73.4 All trim throughout the interior conversion shall be anodized aluminum or formed stainless steel."Mill Finish"aluminum trim is not acceptable due to constant oxidation problems inherent in unfinished aluminum.All exposed corners within the patient compartment shall have padded or rounded corners.The round over trim shapes shall be dent resistant and designed to reinforce the structural integrity of the cabinet. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 73.5 Mitered joints throughout the interior conversion shall have a gap-less,hairline fit.Openings and misalignments at the corners are not acceptable.Misapplied trim to cover manufacturing mistakes is not an acceptable solution to poor design and/or workmanship.Doors shall be warp free.Sliding polycarbonate door assemblies shall be scratch free and all edges shall be smooth and free of saw marks and sharp edges. Cabinets shall fit tightly against the ceiling as well.Doors and drawers shall fit the opening.All doors shall open and close bind-free.Drawers shall slide in and out freely,without drag.All drawers shall be side mounted,full-extension drawer slides, rated at no less than 75 pounds per pair.All hinged wood core doors shall have positive latches. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 0 N 73.6 When specified,flush fitting doors shall have even door to opening gaps.All doors shall open and close bind-free. Drawers shall slide in and out freely,without drag.All drawers shall be mounted on side mounted,full-extension drawer slides, rated no less than 75 pounds /pair.All hinged wood core doors ©N Proposer Initials:spjJM City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 49 14-65 shall have positive latches 73.7 All shelves shall be made of hardwood laminate and be surfaced on both sides and trimmed in aluminum.The shelves shall be held in place by aluminum Unistrut track that is recessed into the cabinet wall to allow for maximum shelf width.Surface mount shelf track shall not be acceptable. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 73.8 When specified,Interior latches will be Chrome Steel D ring latches. ©N 74.STREETSIDE LOWER FRONT CABINETS (A.1) 74.1 The street side main cabinet wall shall be assembled according to the cabinet construction section.The assembly shall be bolted to the module body structure. ©N 74.2 Streetside lower cabinet,exterior Stainless Steel riser,interior laminate white.CPR section w/storage below w/hinged lid & hold open gas strut w/FlexDraw hold down latch.Gibralter countertop Yz"retention lips in attendant area ©N 75.STREETSIDE UPPER REAR CABINET (A.2) 75.1 The street side main cabinet wall shall be assembled according to the cabinet construction section.The assembly shall be bolted to the module body structure. 0 N 75.2 A-2 UPPER:Custom 13" Tall x 30"Wide x 18"Deep upper rear storage cabinet w/sliding polycarbonate doors and one (1) adjustable shelf,upper exhaust vent blower access in left wall. ©N 75.3 A2 MID LEVEL:Custom 23" Tall x 34"Wide x 6"Deep mid level cabinet set located below the upper full depth upper cabinet and backing to the partial depth section of the exterior compartment. ©N 75.4 Right side area 23" Tall x 20"Wide x 6"Deep storage cabinet with two (2)adjustable shelves w/sliding polycarbonate doors ©N 75.5 Left side Glove Box Storage,(3)glove boxes with a side hinged flush to surface polycarbonate door with pull through openings ©N Proposer Initials:cmsw. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 50 14-66 75.6 A2 LOWER LEVEL:Cabinets have been deleted to accommodate full depth section of the raised exterior compartment ©N 76.STREETSIDE CABINETS REARWARD CENTER POSITION (A.3) 76.1 The street side main cabinet wall shall be assembled according to the cabinet construction section.The assembly shall be bolted to the module body structure ©N 76.2 A3 UPPER LEVEL:Custom 13" Tall x 20"Wide x 18"Deep cabinet w/sliding polycarbonate doors and one (1)adjustable shelf ©N 76.3 A3 MID LEVEL:Open storage,Gibraltar counter top 13.5"deep.0 N 76.4 A3 LOWER LEVEL: A 12"deep cabinet below the counter top. Install two (2)4" tall aluminum drawers with aluminum face (laminated)and locking Chrome Steel "D" ring latches,and additional 7/8 key locks. ©N 77.STREETSIDE FRONT WALL (A.4) 77.1 The street side action wall shall be assembled according to the cabinet construction section.The assembly shall be bolted to the module body structure. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 77.2 A4 UPPER LEVEL: Two (2)Custom 13" Tall x 25"Wide x 18" Deep,Street side action wall cabinets,(1)storage area w/ sliding polycarbonate doors and one (1)adjustable shelf,each ©N 77.3 RESTOCKING FEATURE:These cabinets are to have top hinged face frames,with gas strut hold open and positive locking devices to secure the frames in the closed position ©N 77.4 A4 MID LEVEL:Attendant panel,three quarter ply with carbon fiber appearance.Cutouts for one (1)02 outlet,Electric 02 monitor and emergency bypass,SSCOR panel,Time Manager Clock)Radio Volume control,and the main attendant switch panel ©N Proposer Initials:SDJ^M City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 51 14-67 77.5 Attendant area back wall,Stainless Steel Surround,cut outs for One (1) 12V outlet, Two (2) 110V outlets and a sharps pocket, recessed style,for Sage #R1002,bright Stainless Steel ©N 77.6 A4 INSERT CABINET:One (1) 24" Tall x 14"wide x 12"deep Mid level inset Storage cabinet with two (2)adjustable shelves and a pair of side hinged flush to surface polycarbonate doors with non locking Chrome Steel,D ring pull latches. Cabinet located at the forward end of the attendant counter ©N 77.7 SHARPS POCKET:Attendant area back wall, (1),Stainless Steel,for Sage #R1002,Sharps container.©N 77.8 A4 LOWER:Attendant counter with Gibraltar,Corian or equivalent material,countertop with half inch raised edge ©N 78.STREETSIDE CPR SEAT AREA (A.5) 78.1 The street side rear cabinet wall shall be assembled according to the cabinet construction section.The assembly shall be bolted to the module body structure ©N 78.2 Streetside CPR seat area,exterior laminate light grey.0 N 78.4 The back rest pad shall consist of a two inch thick foam sheet over a hardwood plywood backing board and covered in vinyl upholstery ©N 78.5 Seamless padding specifically designed to protect the head is required.The pads shall consist of a two inch thick foam sheet over a hardwood plywood backing board and covered in seamless vinyl upholstery ©N 78.6 Six Point Attendant Restraints.0 N 79.STREETSIDE BULKHEAD CABINET (A.6) 79.1 Streetside bulkhead cabinet & wall with upper A/C removable panel,and opening for oxygen access with hinged Plexiglas door ©N 79.2 A vertical storage cabinet 50 %"tall x 20 1/2"Wide x 16"Deep" shall be located behind the attendant seat.It shall be assembled according to the cabinet construction section.The assembly shall be bolted to the module body structure.Streetside ©N Proposer Initials:sVj*M City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 52 14-68 bulkhead cabinet,exterior laminate light grey,interior laminate white,cabinet is split into two (2)sections.Top of cabinet to have Gibraltar,Corian or equivalent material countertop with half inch raised edge •Upper section will be the radio compartment with hinged wood door w/non-locking latch and vent.Inside @ top will require a wood panel approx.5"wide to mount a multi position switch panel. •Lower section will be a storage compartment with hinged wood door w/non-locking latch. 80.CABINET FRONT OVERHEAD (A.7) 80.1 A 6"deep X 37"wide X 20"tall Electrical Cabinet will be located over the cab/module walk thru opening.This cabinet shall include a solid hinged door hinged on top with gas shock to hold door in upright position for maintenance.This cabinet shall conform to all cabinet construction requirements. ©N 81.PARTITION (A.8) 81.1 Solid Partition,exterior laminate light grey,sliding (clear) Plexiglas window ©N 82.CURBSIDE BULKHEAD JUMP-KIT CABINET (A.9) 82.1 Curbside bulkhead cabinet ALS access,split cabinet. The Bulkhead cabinet shall be assembled according to the cabinet construction section.The assembly shall be bolted to the module body structure. When a shelf is specified unit strut track will be installed.The Unistrut channel shall be made from 1 5/8" x 13/16 " x 16 gauge 6063-T6 extruded aluminum.The channel will be set into Y" deep dado channel shall and fastened to the inner compartment walls,with a minimum of five (5)#8 Stainless Steel screws per each channel. The channel nuts shall be made of case hardened steel with %"- 20 threads and spring loaded to prevent slipping while being adjusted. The shelf mounting bracket shall be made of cast aluminum with a brite finish.The casting size shall be 2" x 2" x 2"and a minimum of 1/8"thick. ©N Proposer Initials:SZ>£Mt City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 53 14-69 Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 82.2 UPPER SECTION:12 inch tall section located above the main jump gear compartment area. •Upper Left section to accommodate a Knox 5502 Medi- vault •Upper right storage cabinet w/Top hinged polycarbonate door. ©N MID-SECTION:w/ (2)hinged 3/8"smoke polycarbonate doors Chrome Steel "D" ring latches,Two (2)adjustable shelves,Solid 3/4"wood,Formica covered with 1/8"edge banding and a Gibraltar lip to the interior opening. A pair of LED Strip lighting on each side of the opening. ©N LOWER LEVEL:Install a single 6" tall by 20"deep aluminum drawer with aluminum face (laminated)from the curbside, accessible from the curbside exterior. Drawer to have a Chrome locking "D" ring latch. Raise the slide out drawer and cabinet floor under it to provide a 22.5"tall opening below. This space is to accommodate a drug box and monitor below it on the compartment floor. The lower section will extend above floor level.Close out to interior with a stainless steel riser over a wood panel. ©N 83. SQUAD BENCH (A.10) 83.1 A minimum 20"wide x 72" long squad bench shall be provided on the curbside of the patient area.It shall be assembled according to the cabinet construction section.The lid shall be split and shall not include posts or wheel cups for a stretcher. Exterior Stainless Steel riser,interior laminate white,(2)hinged lids w/hold open gas struts and Southco rubber "FlexDraw " hold down latches HEAD END SEATING POSITION::One (1)pair of six point seat belts shall be installed in this area for the seated position.The belts shall conform to FMVSS Standard No.209 (seat belt),and ©N Proposer Initials:SDJM City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 54 14-70 210 (seat belt anchorage). FOOT END SEATING POSITION:One (1)pair of six point seat belts shall be installed in this area for the seated position.The belts shall conform to FMVSS Standard No.209 (seat belt),and 210 (seat belt anchorage). On the curbside wall there shall be Four (4)rectangular cushions for backrests.These too shall be easily removed for bio-hazard cleaning. The cushions shall be attached to the lids with Velcro to make them easy to remove for bio-hazard cleaning. Two additional belts shall be supplied for backboard retention of a secondary patient. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 83.2 BIO-WASTE COLLECTION AREA:A biological waste area shall be provided and located at the head of the bench.One six quart (346 cubic inch),rimmed plastic waste container shall be supplied and fitted into the "Bio-waste"enclosure.The enclosure shall be covered with a red Plexiglas hinged door.The door pull shall be full length.A white colored "Bio-waste"symbol and legend shall be applied to the door.The sharps containers shall be a drop in,horizontal top drop,Sage #R1002 rimmed plastic container with closure. Trash &sharps containers to be included ©N 84.CURBSIDE CABINETS 84.1 CURBSIDE WALL IV SUPPLY CABINET.:The curbside wall cabinet wall shall be assembled according to the cabinet construction section.The assembly shall be bolted to the module body structure. Locate at the head of the bench,Cabinet to butt up to the upper curbside cabinet. The top portion will accommodate the curbside 02 outlet and an open storage bin. The center portion will be for IV supply storage and is to have ©N Proposer Initials:crp/n^ City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 55 14-71 two (2)adjustable shelves w/aluminum front lips and a hinged Plexiglas door. The bottom section will be open storage with four (4)adjustable dividers,for IV needle storage. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 84.2 CURBSIDE UPPER CABINET:The curbside upper cabinet wall shall be assembled according to the cabinet construction section.The assembly shall be bolted to the module body structure. Curbside storage cabinet,exterior laminate light grey,interior laminate white. Cabinet over squad bench,divided into two sections w/hinged (flip up) 3/8"polycarbonate doors w/Chrome Steel "D"ring latches ADJUSTABLE VERTICAL DIVIDERS: QUANTITY: Two (2)Sets of six each Install a set of six (6)Plexiglas dividers into each section of the upper curbside cabinet. RETENSION LIP: Two (2) Both sections to have %" tall retention lip across the front edge. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 84.3 INSIDE ACCESS TO AN EXTERIOR COMPARTMENT: Location:Curbside rear,Access into upper forward portion of the curbside rear compartment. Configuration: Two (2)side Hinged Plexiglas Doors, non locking Chrome Steel pull latches ©N 85.ATTENDANT SEAT 85.1 A bucket type attendant seat with built in child safety seat shall be installed.The seat shall be bolted to a pedestal with 3 point ©N Proposer Initials:^pjnff. Cityof Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 56 14-72 86.1 retractable seat belts.The seat shall be capable of sliding both front and backward.The seat shall be upholstered to match the vehicle interior,and shall be capable of adjustment from front to rear.Seat shall conform to FMVSS Standard No.209 (seat belt), 210 (seat belt anchorage).Manufacturer must be able to supply compliance documentation. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 86.CENTER CONSOLE DRIVER AREA CONSOLE FOR FREIGHTLINER CHASSIS:A center console shall be installed in the driver area and attached to the floor.It shall be removable for engine service and include adequate service loops on the wire harness Console to be fabricated from .125"aluminum with a texture paint (Dark Grey)finish. It will incorporate five sections. SECTION #1 is a 6" long level forward section. The forward,curbside 6"section of the console will be reserved for the MDT install area.The Passenger side of the front console section needs to be reinforced to accept specified the MDT mount. The forward streetside side area will be reserved for the Chassis heat AC controls and the added meters. SECTION #2 There will be a 6.25""long angled panel section. This will be used for the Federal EQ2B Siren control,and the Whelen Siren Control. SECTION #3 To the rear of section #2 will be a flat panel with the Whelen Traffic Advisor control,the Emergency start switch, and Two (2)Intercom push to talk buttons. SECTION #4 To the rear of section #3 will be a flat panel with 12V USB outlets,Cup holders. SECTION #5 will be located behind the main console,and will be for open map storage w/adjustable polycarbonate dividers, w/ (2)cup holders. Proposer Initials:57?/^ City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle ©N Page 57 14-73 A single of Dual Port USB charger outlet will be located on each side of the front console.The David Clark U3810 module will be located inside the center console NOTE:Exact layout to be determined at Pre-construction. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 87.HEAD PROTECTION -CURB SIDE ACCESS DOOR 87.1 A seamless pad specifically designed to protect the head during egress is required.The pad shall consist of a two inch thick foam sheet over a hardwood plywood backing board and covered in seamless vinyl upholstery. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 88.HEAD PROTECTION -REAR ACCESS DOOR 88.1 A seamless pad specifically designed to protect the head during egress is required and shall comply with current Federal Specification KKK-A-1822.The pad shall consist of a two inch thick foam sheet over a hardwood plywood backing board and covered in seamless vinyl upholstery. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N INTERIOR TRIM AND COLOR 89.FLOOR COLOR/MATERIAL 89.1 The floor covering in the patient compartment shall be Loincoin II Flecks,Color Onyx #150UV . This floor incorporate an Anti microbial protection. It will be coved up the side walls a minimum of 3" ©N Proposer Initials:spj*M City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 58 14-74 90.UPHOLSTERY COLOR,REAR 90.1 Unless otherwise specified,the upholstery color for the patient compartment shall be Sierra Light Gray TL -2000 ©N 91.WATER FALL UPHOLSTERY,REAR 91.1 UPHOLSTERY JOINERY TYPE:All long runs of cushion corners shall be vinyl wrapped. Sewn seams are permitted only on the cushion corners.Sewn seam lengths shall be restricted to the cushion thickness.All vinyl surfaces shall be pulled tight against the foam,utilizing a hardwood plywood backing board. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 92.LAMINATE COLOR, 92.1 Unless otherwise specified,the laminate color for all interior cabinetry shall be - Light Gray - D 355. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 93.LAMINATE COLOR,ATTENDANT PANEL 93.1 Unless otherwise specified,the laminate color,used on the action wall panel will be in a Carbon Fiber finish. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 94.POLYCARBONITE DOORS 94.1 Unless otherwise specified,the Sliding Polycarbonate shall be .240 thick. Sliding doors will have full height anodized aluminum handles installed,in addition 1"diameter finger holes will be provided for ©N Proposer Initials:SD£W. City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 59 14-75 cable ties. Hinged Doors shall be .375" thick and be installed recessed into the aluminum extrusion to provide a flush surface. The Color shall be Light Tint. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 95.SEAT CUSHIONS 95.1 All seat cushions in the patient area shall be 2"foam,double stitched seams.They shall be attached with Velcro fasteners for quick release and cleaning ©N 96.COUNTER TOPS 96.1 All counter tops are to be high strength 1/2-inch thick Gibralter solid surfacing material (like Corian).The material shall be edged with a one (1) inch wide strip to prevent equipment from sliding off the countertop as well as retaining any spilled fluids. The entire countertop shall be glued and sanded to create a continuous waterproof tray that will not absorb fluids and is easy to clean.It shall also be impervious to all high strength cleaning and disinfecting solutions Color:Steel Grey Tempest. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 97.HEADLINER 97.1 The patient area ceiling shall be constructed of a bright white laminate over 1/4 inch luan plywood.This material shall be smooth,easy to clean,and durable.Headliner material that is padded or upholstered in any way will not be considered due to the lower degree of durability and the risk of contamination inherent in such materials. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications ©N Proposer Initials:ga£2g Cityof Newport Beach RFP No. 16-24 Emergency Ambulance Medical Vehicle Page 60 14-76 for Ambulances standards 98.INNER DOOR PANELS: 98.1 An inner door pan shall fit flush with the inner edges of the door. Inner door pans that do not fit flush will have sharp or ragged edges exposed and will not be acceptable.The panels must be attached to the door structure with machine screws and Nutserts to prevent stripping.Sheet metal screws or rivets will not be accepted.A closed cell cross linked polyolefin foam tape shall be used beneath the inner door panels to isolate the panels from the doorframes.This process will prevent door rattling. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 0 N 98.2 Unless otherwise specified,the laminate colors for all upper door panels shall be - D355 Light Gray,matte finish laminate ©N 98.3 The lower portion of the patient area entry doors shall be covered with single sheets of stainless steel. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 98.4 The Mid level of the inner door panels will incorporate a reflective stripe. The stripe will be 6" tall and the width of the inner door panel.It will be made from Red #983-72 3M Conspicuity reflective safety stripe material ©N 99.STAINLESS STEEL DOOR SILLS 99.1 Curbside Door sill,bright Stainless Steel,1 1/2"x 2 1/2"located at top edge of entry step. Rear entry door sill bright Stainless Steel sill w/ramp edge,1 Yz" x 4".located above the rear riser and extending into the module. ©N 100.STREETWALL RISER 100.1 The street side riser beneath the main cabinet wall shall be covered with a single sheet of stainless steel.The stainless material shall be installed flush with the riser and trimmed at the top and both sides so as to cover the edges.The bottom of the ©N Proposer Initials:cmjm City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 61 14-77 material shall be positioned so that, upon installation, the 4" rolled floor will seal against the stainless steel. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 101.BENCH RISERS 101.1 The curbside riser beneath the squad bench shall be covered with a single sheet of stainless steel.The stainless material shall be installed flush with the riser and trimmed at the top and both sides so as to cover the edges.The bottom of the material shall positioned so that, upon installation, the 4" rolled floor will seal against the stainless steel.Designs that do not include this stainless steel riser will not be considered as they will not be capable of protecting the riser from damage due to cot movement,etc. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N WARNING DEVICES 102.LIGHTBAR 102:1 FRONT LIGHT BAR ALTERNATIVE:WHELEN LED "M" SERIES LIGHTS (7) Total, Red w/ Red lens, (2) White w/ Clear lens. Center light to be steady burning.Chrome flanges included. (4) M9R Red (flashing) (2) M9C White (flashing) (1)M7RS Red (steady) (6) M9FC Chrome Flange (1)M7FC Chrome Flange The Two (2)center lights shall be steady burning Reds. "R"_"W"-"R"-"R"-"R"-"W"-"R" M9 -M9 -M9 -M7.-M9 -M9 -M9 Opticom (LED) GTT 794H Emitter The emitter shall be wired "ON" with the Primary warning Light switch and shall disengage when the vehicle is place in "PARK" ©N Proposer Initials:SD^M City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 62 14-78 or "NEUTRAL". There shall be a separate cutout switch installed on the front switch panel. 103.TRAFFIC ADVISOR REAR UPPER 103.1 One (1)Whelen Low Profile #TAM85 with (8) TIR6 Super LED Traffic Advisor mounted above the rear doors with the control head in the cab console. NOTE:The Traffic Advisor shall be wired directly to the batteries ©N 104.WARNING LIGHTS REAR UPPER 104.1 The module shall have two (2)Whelen M9 Series LED (red)w/ chrome flange warning lights with RED lenses mounted on the rear outboard corners of the module ©N 105.WARNING LIGHTS REAR MID-LEVEL 105.1 The module shall have (2)Whelen M9 series LED (Amber)w/ chrome flange warning lights with Amber lenses mounted on the rear of the module at window level.They should be positioned to show through the windows when the doors are in the open position ©N 106.WARNING LIGHTS REAR LOWER LEVEL 106.1 The module shall have two (2)Whelen M6 Series LED Red Warning lights on the lower rear of the vehicle,above the Brake Taillights,installed in top position of Whelen #M6FCV4 Chrome Flange ©N 107.WARNING LIGHTS,MODULE SIDES 107.1 The module shall have four (4),Whelen M9 series LED (Red)w/ Chrome Flange warning lights with RED lenses.Two (2)located on the streetside upper corners and (2) on the curbside upper corners ©N 108.FORWARD WARNING LIGHTS Proposer Initials:^pj^f. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 63 14-79 108.1 There shall four (4)Whelen M7 Series LED with Red lenses mounted in Chrome light housings in the grille ©N 109.FRONT FENDER WARNING LIGHTS 109.11 Intersection lights,front fenders,(2)Whelen M/D Series LED Split Red/Clear w/chrome flange warning lights with Clear lenses,(1) on the streetside fender and (1) on the curbside fender ©N 110.REAR FENDER WARNING LIGHTS 110.1 Intersection lights,Rear fenders,(2)Whelen M6D Series LED Split Red/Clear LED w/chrome flange warning lights with Red/Clear lenses,(1)above the streetside fender and (1)above the curbside fender ©N 111.SCENE LIGHTS,REAR 111.1 There shall be two (2)Whelen M6LZC Series LED (clear)w/ chrome flange and with 26 deg.Optics mounted on the rear of the module just above the rear doors ©N 111.2 The above specified rear scene lights will be wired to activate when the vehicle is placed in reverse gear in addition to operating when the rear doors are opened ©N 112.SCENE LIGHTS,SIDE 112.1 There shall be (4)total,(2)per side Whelen M9LZC Series LED (clear)w/chrome flange.Lights shall be mounted next to the red warning lights ©N 113.BROW LIGHT: 113.1 Add "Brow Light"Whelen Pioneer #PFP2 (Dual Flood Pioneer Plus) Mount to Module w/Steel Radius Mount to match body extrusion. Note:The Mounting hardware is to be powder coated white. Locate:Mount on front radius of Module (centered) ©N 114.CHROME FLANGES 114.1 All emergency and scene lighting specified is to have Chrome ©N Proposer Initials:^DJTff Cityof Newport Beach RFP No. 16-24 Emergency Ambulance Medical Vehicle Page 64 14-80 flanges installed to enhance the appearance of the unit 115.SIREN SYSTEMS 115.1 WHELEN ELECTRONIC:The vehicle manufacturer shall supply and install a Whelen 295SLSA-1 siren,CA spec,100 Watt w/mic,(hi-lo deleted),flush mounting bezel,(horn ring control). This siren shall be compliant with California Title 13 requirements. Connect to Federal Siren Speaker in left front bumper extension as listed below. ©N 115.2 FEDERAL SIREN ELECTRONIC:Siren electronic,Federal EQ2B Locate in front console. Connect to Federal Siren Speaker in left front bumper extension as listed below. ©N 116.OPTICOM 116.1 OPTICOM (LED) GTT 794H Emitter (Self-contained)NOTE: (Includes Activating via Primary Switch,and wired thru Park/Neutral cut-off. ©N 116.2 OPTICOM DEFEAT VW AUTO RE-SET:Add a momentary switch in the "C"position in front center console. NOTE:Once the circuit has been defeated it needs to automatically re-set when the Primary-Secondary switch is activated ©N 117.SIREN SPEAKER 117.1 SIREN SPEAKERS,FEDERAL One (1)Federal 200 watt,#BT200 connect to the Specified E2QB One (1)Federal 100 watt,#ES100 Connect to the Whelen Siren Recessed thru front OEM bumper (outboard sections). ©N 118.AIR HORN SWITCH 118.1 Air horn system to be supplied with chassis provide a single Line Master Clamshell style foot switch on drivers side in cab. Location to be determined at Pre construction conference ©N 119.HEADLIGHT FLASHER 119.1 The vehicle headlights shall alternately flash through the activation of the appropriate switch on the cab control console. The flasher circuit must be designed so the daytime running ©N Proposer Initials:SVJIM Cityof Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 65 14-81 lights (low-beams)are cut out when the flasher circuit is engaged.This is an OEM requirement to reduce heat build-up in the light housing,which could result in severe damage 120.WARNING LIGHT FLASHER 120.1 An ambulance flasher module shall be installed to supply momentary power (flash)for the warning lights 0 N 121.UPPER BRAKE LIGHT 121.1 A Brake light,rear upper center,Whelen M7 Series LED (red)w/ chrome flange,shall be installed in the center of the mod directly above the rear entry doors. It shall be wired to the chassis brakes and operate in conjunction with the brake lights ©N 122.MARKER LIGHTS 122.1 Front,rear and side FMVSS marker lights shall be LED type: Front;amber lights are supplied on light bar. Side;two red lights in upper rear of module side. Rear;five red lights in upper corners and above doors module rear ©N 123.TAIL LIGHT FLANGE 123.1 Whelen #M6FCV4 Chrome Flange Note:This is a Four (4) light Flange includes the tail lights and 1 emergency flashing light. Install left and right rear above the tread bright ©N 124.TAIL LIGHTS 124.1 Whelen brand back-up,turn and brake lights shall be supplied as follows: (2)Whelen M6T LED (amber)w/arrow turn signal (2)Whelen M6BTT (red)Stop/Tail light (2)Whelen M6BUW LED (clear)back-up light ©N 125.DOOR MARKER LIGHTS 125.1 ENTRY DOOR MARKER LIGHTS:Install Whelen LED Red door marker lights on the upper and lower corners of each inner module entry door panel. Quantity:Six (6).Two (2)per door. 0 N Proposer Initials:SV^Tft City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 66 14-82 Configure to come on when the door is opened 125.2 COMPARTMENT DOOR MARKER LIGHTS:Whelen LED Flashing lightsto all exterior compartment door inner panels. (1) on each short door panel @ top of M2 compartment,and (2)per door @ top &bottom on alltalldoor panels -M1, M3,M5,M7. Locate:Outer Corners Total of 12 lights. ©N 126.DOOR REFLECTORS 126.1 Red reflectors shall be installed on the inside on the patient area doors 0 N 127.BODY REFLECTORS 127.1 The module shall have amber reflectors in the lower front corners and red reflectors in the lower rear corners ©N ELECTRICAL CONTROL CENTER 128.ELECTRICAL SWITCH PANEL FRONT 128.1 Two (2)consoles areas shall be installed in the cab. . Under no circumstances shall the consoles interfere with the OEM vehicle controls or gauges,nor shall the control panel be installed in such a manner as to interfere with the OEM vehicle controls, gauges,or the driver's line of vision. All switches shall be high cycle Rocker Switches,with Silver Contacts and Nickel Plated Brass Connection Blades.They will incorporate Color Coordinated LED illumination.Each switch will be back lit and labeled with specific function.(Including module disconnect switch).System shall also incorporate an automatic shutdown timer (5 minute) activated when ignition is turned off. Switch MASTER ON Switches and legends are to be back lit ©N 128.2 LOWER CAB CONSOLE:The lower console shall be fabricated to complement the OEM dashboard material, and color. The console shall be installed at floor level to allow for the Siren controls,Whelen T/A control and other functions to be within reach of the driver. Lower console mounted between the cab seats with a forward ©N Proposer Initials:c^p/^f Cityof Newport Beach RFP No. 16-24 Emergency Ambulance Medical Vehicle Page 67 14-83 section to accommodate the OEM Climate Controls and the converter added Digital meters.The Emergency Start switch will be located in the mid-section of the console. Cup holders and open map storage will be located rearward. 128.3 UPPER CONSOLE:Primary control panel. A custom fabricated panel will be located into the chassis overhead storage area.All functions shall be identified by etched plastic labels. All jeweled lights shall be Cole Hersee,PL 86-RC A.PRI-SEC-LIT RED/AMBER LED B.HEAD LIGHT FLASER -LIT CLEAR LED C.OPTICOM SWITCH D.BROW LIGHT SWITCH E. BACK UP ALARM-RESET TYPE-MOMENTARILY ON (NON LIT) F.LEFT SCENE WHITE LIT LED G.REAR SCENE WHITE LIT LED H.RIGHT SCENE WHITE LIT LED I.PATIENT DOME 3-WAY -LIT AMBER LED J.PATIENT A/C HEAT 3-WAY -LIT BLUE LED K.EXHAUST - 3 WAY -LIT AMBER LED L.MOD.DISCONNECT -GREEN LIT LED P.PILOT LIGHT -PARKING BRAKE RED LED Q.PILOT LIGHT -DOOR OPEN RED LED R.PILOT LIGHT -EMERGENCY START RED LED S.PILOT LIGHT -ALTERNATOR RED LED T.PILOT LIGHT -MASTER ON GREEN LED 0 N 129.12 VOLT CONSOLE POWER SOURCES 129.1 Electrical outlet 12 volt,Blue Sea #1016,Dual USB Port. Location: (2)Center console,One (1) Driverand One (1)passenger side ©N 129.2 Electrical outlet 12 volt,Blue Sea #1011,One (1)cigarette lighter style. Location Rear section of the front console between the cup holders. ©N 130.MAP LIGHT 130.1 Map lights, (2)dual Red/White LED map lights located in cab overhead console,(1)above driver,(1)above passenger.©N 131.RADIO MOUNTING BEZEL Proposer Initials:SVJ2M Cityof Newport Beach RFP No. 16-24 Emergency Ambulance Medical Vehicle Page 68 14-84 131.1 Two (2)Radio mounting bezels will be provided and installed in the front console.These are to adapt radio port in console to specified two-way radios,Steel,Black finish. Quantity:Two (2) Make and model of radios to be provided prior to build ©N 132.AUDIBLE CHIME 132.1 Module Door Open Audible Chime. Wire to a module entry and compartment doors ©N ELECTRICAL PATIENT COMPARTMENT 133.ELECTRICAL SWITCH PANEL ATTENDANT AREA 133.1 All switches shall be high cycle Cole Hersey,or approved equivalent Rocker Switches,with Silver Contacts and Nickel Plated Brass Connection Blades.They will incorporate Color Coordinated LED illumination.Each switch will be back lit and labeled with specific function.Ten (10)positions: A.DOME 3WAY,Cole Hersey LED ,black,lit amber. B.DOME HI-LO,Cole Hersey,black,non lit. C.CABINET LIGHTS D.ATTENANT AREA LIGHT E.EXHAUST VENT F.ELECT SUCTION,Cole Hersey LED, lit amber. G.PATIENT HEAT A/C,3-way Cole Hersey LED, A/C on lit Switch blue H. A/C, FAN HI-LO,3-way,Cole Hersey,non-lit. I. A/C,HEAT-COOL,3-way,Cole Hersey,non-lit. J. 02 3WAY,Cole Hersey LED ©N 134.ELECTRICAL SWITCH PANELS OTHER 134.1 All switches shall be high cycle Cole Hersey,or approved equivalent Rocker Switches,with Silver Contacts and Nickel Plated Brass Connection Blades.They will incorporate Color Coordinated LED illumination.Each switch will be back lit and labeled with specific function. Electrical Switches/Defeat,Panel. Switch defeat,PATIENT DOME,side and rear door,Cole Hersey,non-lit. Switch defeat,RIGHT FLOOD,side and rear door Cole Hersey, ©N Proposer Initials:SV£M Cityof Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 69 14-85 non-lit. Switch defeat,REAR FLOOD,side and rear door Cole Hersey, non-lit 135.DOME LAMPS LED 135.1 Eight (8)Whelen nine diode,white LED dome lights shall be installed in the patient area ceiling.These will be configured for two light intensities,high and low.The lens shall be high strength Lexan.The lights shall be recessed into the headliner and shall not protrude from the ceiling more than 1/8".Each light shall not draw more than 1.5 amps at full intensity.All dome lighting shall be controlled via multi-way switching at the patient action,module doors,area and the front electrical control console ©N 136.CABINET LIGHTING 136.1 Interior cabinet lighting, LED light STRIPS in each interior cabinet,action wall panel lighting attendant area,and ALS cabinet to have LED strip lighting,both activated w/switch in action area. ©N 137.STEP WELL LIGHT 137.1 A Grote LED light shall be installed in the side step well to light the step well area when the side access door is opened.The light shall be activated by a magnetic door switch installed on the door as described elsewhere within this document ©N 138.ATTENDANT LAMP 138.1 12 Volt LED Strip Lighting mounted to bottom of upper cabinet to illuminate the action wall area.Lights are to be activated w/ switch in action area. ©N 139.RESTOCKING LIGHT TIMER 139.1 15 MINUTE TIMER: A variable 0 to 15 minute,spring wound, mechanical timer switch shall provide temporary illumination of the patient cabin for check out purposes.The switch input shall be wired directly to the vehicle batteries. The switch shall be located on the curbside wall,one by the C/S ©N Proposer Initials:SVJ&K City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 70 14-86 access doors over the squad bench, The timer circuit shall comply with the latest revision of KKK-A- 1822. LIGHTS POWERED BY TIMER:The aforementioned timers shall power Three (3) LED dome lights over the cot 140.ELECTRICAL OUTLET 12V DC 140.1 The 12 volt outlet shall be wired through a 10 amp auto reset circuit breaker.All outlets,unless noted otherwise below,shall be on with the ignition timer/circuit.All 12 volt outlets shall be labeled. Adapter type shall be a cigarette lighter style. A 12 volt electrical outlet shall be installed at the attendant action area. A 12 volt electrical outlet shall be installed in the curbside bulkhead cabinet next to the 110V outlet ©N 140.2 The 12 volt outlet shall be wired through a 10 amp auto reset circuit breaker.All outlets,unless noted otherwise below,shall be on with the ignition timer/circuit.All 12 volt outlets shall be labeled. Adapter type shall be a Dual USB style. A dual 12 volt electrical outlet shall be installed at the attendant action area between the 110V outlets. A 12 volt electrical outlet shall be installed in the curbside bulkhead cabinet next to the 110V outlet. 0 N 141.ELECTRICAL OUTLET 120V AC 141.1 Two (2)Duplex 120V,15 amp interior electrical outlets shall be installed.Outlets shall have an indicator light to be on when outlets are hot. Two (2)at the action wall. One (1) in the upper section of the ALS cabinet ©N 142.SHORE POWER 142.1 The vehicle shall be equipped with a 120V Kussmaul Super Auto ©N Proposer Initials:SD£Ml City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 71 14-87 Eject 20 Amp.shore power inlet. Note: Wire to the specified Newmar charger in the inverter cabinet. Cover Color:RED Locate Mount shoreline plug on the streetside of the module above the intermediate compartment 143.BATTERY CHARGER 143.1 BATTERY CHARGER/INVERTER:Newmar/Kussmaul #430- 120000 50 amp Charger,12000 Watt inverter. Locate:Charger/inverter inside streetside intermediate compartment,lower right side. Charge monitor 020-4290-0, Locate:Charge Monitor above exterior shore inlet. Inverter Panel 0202-4289-0 Locate:Inverter panel to be located in the attendant area. ©N 144.BLOCK HEATER WIRING 144.1 Block heater wiring, from Block Heater to Shore Power,switch on partition behind driver seat base ©N 145.PATIENT AREA CLOCK 145.1 Clock,Emergency Time Manager,mounted in action wall panel, chimes.©N 146.REVERSE CAMERA 146.1 REVERSE CAMERA WITH ABOVE WINDSHIELD MOUNTED 7" LCD MONITOR: Install a Voyager AOS713CMB Kit. Backup camera over the rear doors,install the 7" LCD screen on the cab upper storage pocket above the driver's seat.This will require a custom fabricated and painted steel mounting plate. Wire to activate when the vehicle is placed into reverse. ©N 147.LIQUID RIDE CONTROL SYSTEM 147.1 Liquid Ride Dump System to function as follows: To dump automatically when Left rear door is open,and fill when it closes. This defeat switch will not interfere with the OEM switch. ©N Proposer Initials:SV^M City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 72 14-88 147.2 In addition to the OEM factory switch on the front console the converter is to provide a defeat switch on the inner door panel of the right rear door Converter added switches shall be Cole Hersey,LED Euro style and color coordinated with their specific functions.Santex,back lit 0 N ELECTRICAL AND MECHANICAL -STANDARD 148.ELECTRICAL SYSTEM 148.1 ELECTRICAL SYSTEM 12 Volt -General ©N 148.2 MODULE GROUNDING:A minimum of (2) two braided ground straps shall be through bolted to the chassis frame and the floor structure of the modular body.The bolts shall be at least 3/8 diameter.A flat washer shall be provided under the head of the bolt,over the strap lug.Additionally an internal tooth lock washer shall preclude loosening.Conventional stranded copper cables are not acceptable because they do not suppress RFI and does not meet SAE J551 ©N 148.3 GENERAL GROUNDS:To comply with current Federal specification KKK-A-1822 plus enhance ground quality and reduce trouble shooting time,all devices wired within the ambulance conversion shall be centrally grounded.Each device shall have a separate ground wire routed to a central buss bar then grounded via fine strand cable to the module body. Local grounds are acceptable only when the device is drawing at or less than 100 milliamps (0.1 amps) ©N 148.4 12 VOLT WIRE:All wires within the ambulance harnesses shall meet current Federal specification KKK-A-1822.All wiring shall be SXL type wire.Although GXL type wire is Ford QVM approved it does not have as high a rating as SXL and so therefore is not acceptable.Wire gauge used shall be 150 percent of circuit requirement.All crimps on 12 gauge or smaller thickness wire shall be done utilizing a hydraulic crimper. Manual crimping is not acceptable because it is more susceptible to long term failure.The wire shall be color coded, number coded and function printed every six inches.Every circuit shall be protected with an automatic resetting circuit breaker. Wire conductors shall be stranded copper. ©N Proposer Initials:ST)£M City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 73 14-89 148.5 148.6 149.1 149.2 Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards WIRE PROTECTION:All wire within the conversion shall be protected and run in split convoluted loom with a melting temperature of 300 degrees,Fahrenheit.All wire harnesses shall be clamped and routed to eliminate possibility of damage due to cut/chaffed wire.Grommets made of rubber or plastic shall be used where harnesses pass through metal or wood.Large holes and irregular shaped wire passages shall use automotive edge trim to protect the wire conduit/loom.Wire harnesses shall be neatly clamped into protective routing areas away from heat sources,unfriendly edges or moving devices SPLICE-LESS WIRING:Each converter-added circuit shall be powered through an individual wire that is free of any splices within the wire harness.For ease of troubleshooting and for greater reliability,one end of the wire shall plug directly into the output module and the other end shall connect to the device or the pigtail of the device being powered. The use of daisy-chain wiring will not be acceptable 149.CIRCUIT BOARD RMR Rail System,W/ LED Diagnostics CIRCUIT BOARD:The single relay control board is a fully integrated relay control board designed and built to IPC Class 3* guidelines.The VF4 style socketed relay is rated at 20A at 24 VDC with built-in on-board diode suppression.Three status indicators for Blown Fuse,Coil Power and Load allow for intuitive operation and troubleshooting.Also included is a medium sized ATO blade style fuse /circuit breaker holder that is rated for 20A. Wiring connections are made via a WAGO Cage Clamp removable lockable connector,which provides a secure,vibration proof and corrosion resistant wire termination. Installation time is reduced by as much as 75%. All of these features are mounted in a 2"x2"DIN Rail mountable package.Clearly,the Single Relay Control Board is a best-in- class solution for Emergency Vehicle relay applications. Proposer Initials:SV^M City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle ©N ©N 15 N ©N Page 74 14-90 Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 150.GROUND STRAPS,MODULE TO FRAME 150.1 Four (4) 7/8" wide by 1/8" thick, fine strand,woven straps shall provide a ground path from the module body to the chassis frame.Woven straps filter out RFI noise originating from alternators,strobe power supplies and other devices,that may find their way into intercom,stereo and two way communication radios.Each end of the ground straps shall be through bolted with 3/8"diameter,grade 5 or 8,hex head bolts and lock nuts. Each connection site shall be cleaned to the bare metal prior to fastening the strap.The connections shall have a dielectric anti corrosion spray applied ©N 151.FOUR BATTERY SYSTEM 151.1 The FOUR (4)battery system,as noted in the "Chassis"section of these specifications shall include Four batteries on a roll out tray in the bottom of the streetside intermediate compartment. The two (2)chassis batteries shall be primary and utilized for starting the vehicle and running the patient module.There shall be an additional third battery to be continuously charged but isolated from the primary batteries.In the event the primary batteries are depleted there shall be an emergency start circuit that upon activation ties the secondary batteries to the primary batteries.Each system shall be able to be monitored by a common voltmeter.If the system for emergency purposes is tied together a jeweled,red,one-inch (1") light shall be activated. This light shall remain activated until it is reset by a method that is separate and not obvious to the driver.The intent of this system is to always have backup battery power for emergency starting and to force a system review when an "Emergency Start"event occurs A Fourth Battery is to be an isolated power supply for the communication equipment. Locate in the battery tray in the bottom of the intermediate compartment. This battery is to be tied to the chassis charge system and to the second output on the specified battery charger. ©N Proposer Initials:SDjDK City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 75 14-91 152.AUTO THROTTLE 152.1 A Freightliner high idle device shall be supplied to control the high idle system ©N 153.SHUT-DOWN TIMER 153.1 The chassis electrical system shall incorporate an automatic shut down timer (5 minute)activated when ignition is turned off. The timer shall also be adjustable to 10 or 20 minute time segments ©N 154.ELECTRIC DOOR LOCKS 154.1 Power activated door locks shall be installed on Patient area Access Doors.Locks shall be activated by cab door lock switch. Locks may be overridden by a manual slide lever or by the door key ©N 155.ELECTRIC COMPARTMENT LOCKS 155.1 Power activated door locks shall be installed on all Exterior Compartment Access Doors.Locks shall be activated by cab door lock switch.Locks may be overridden by the door key. ©N 156.ELECTRIC DOOR LOCKS WIRED TOGETHER 156.1 Cab,and module doors are to be wired into the same circuit so that the NAVISTAR remote controls all locks ©N 157.ELECTRIC DOOR LOCKS REMOTE SWITCH 157.1 Remote door lock release,upper portion of the rear license plate housing,controls all locks ©N 158.COMPARTMENT LIGHTING 158.1 LED strip lighting on all exterior compartments.(2)per compartment. Locate:Inside compartment doorframes.Run full height on both sides ©N 159.12 VOLT POWER 159.1 12 Volt wiring, pair.Positive -Negative,20 amp protection U, 12 gage wire w/10 amp circuit breakers,3 feet of coil. ©N Proposer Initials:SDJtM City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 76 14-92 Note:Quantity:Three (3) NOTE:Power for these (3)will come from AUXILARY POWER BATTERY Locate:(1)set for the drivers side Portable radio charger. Locate:(1)one set behind the passenger seat,for the passenger side Portable radio charger. Locate:(1)one set in the streetside rear exterior compartment, for "Box" light. Configure:Wire continuously Hot to designated AUXILARY POWER BATTERY in the streetside intermediate compartment. NOTE:Label all wiring. 160.RADIO POWER 160.1 (1) AUXILARY RADIO POWER TERMINAL STRIP (3)Gang:(6) gage Positive - (6)gage Negative -Ignition. Located inside Radio Compartment.Add a (7)Position back lit switch plate w/legends (listed below)inside upper section of Radio Compartment. (4)Pos-Neg 12 gage Circuits from terminal strip. (3)out of the (4)circuits need to be wired through a Momentary (Normally On)Rocker Switch protected with 20 amp circuit breakers terminating in the following Switches: Circuit 1:(W/Rocker Switch)"DRUG VAULT" -Terminate ALS Cabinet Circuit 2:(W/Rocker Switch)"KEY VAULT"-Center Console Circuit 3:(W/Rocker Switch)"MODEM" -Radio Compartment Circuit 4:(W/Out Rocker Switch)"MDC" -Center Console Configure:Wire 6 gage continuously Hot to designated AUXILARY POWER BATTERY in the curbside intermediate compartment. Label all wiring. ©N 161.ANNTENA LEADS 161.1 Antenna wiring (2)RG58A/U coax, Originate in a forward roof location with Stainless Steel (Interior) access plates. #1 Antenna to terminate inside Radio Compartment #2 Antenna to terminate inside Radio Compartment (Spare) ©N 162.CAT 5 WIRE: 162.1 Supply & Install Cat 5 wire in three locations w/ 3 feet of coil: -From Radio Compartment to Center console for MBC -From Radio Compartment to Center console for Key Vault ©N Proposer Initials:SVJtM City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 77 14-93 - From Radio Compartment to ALS Cabinet for Drug Vault NOTE:Customer to install connectors and do the final connections,contractor to supply wire only 63.INSTALL CUSTOMER-SUPPLIED ELECTRONIC COMPONENTS 163.1 INSTALL (2)CUSTOMER SUPPLIED PORTABLE RADIO CHARGERS: Location:Rear of center console map box,Constant Hot,Refer to Prints ©N 163.2 INSTALL CUSTOMER SUPPLIED RADIO HEAD &CABLES: -Install radio head w/custom bezel in the center front console in cab. -Install radio cable from center console in cab to the radio compartment. -Install radio speaker in cab (upper headliner centered) NOTE:Customer to install radio bases,and do final connections ©N 163.3 INSTALL CUSTOMER SUPPLIED GPS ANTENNA LEAD: Quantity:One(1) Originate:#1 Module roof,Streetside forward corner. Terminate:Radio Compartment ©N 163.4 INSTALL A CUSTOMER SUPPLIED KNOX KEY SECURE: Install in the forward right corner of the front console below the MDT screen. Requires a constant hot power supply. ©N 164.DAVID CLARK INTERCOM RADIO INTERFACE 164.1 Furnish and install a David Clark system per Newport Beach Specification PKG There will be (2)buttons,one on each side of console face. A David Clark 3800 series communication system One (1), Master Station box #U3800 to be located overhead,aft,between the driver and the passenger. Box shall accept two (2)head set plugs with master and individual volumes.One (1)hanger for each of the two (2) headsets shall be mounted adjacent to the box. One (1),Remote Headset Station box #U3801 to be located on ©N Proposer Initials:SV^M City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 78 14-94 the forward wall of the action area. Box shall accept one (1)head set plug with individual volume. One (1)hanger for the headset shall be mounted adjacent to the box. One (1), Dual Radio Interface Module box #U3812 shall be located next to the radios. Three (3)Headsets:(2)#H3442 and (1)#H3441 One (1)hanger for each of the three (3)headsets shall be mounted adjacent to the box. Note:All boxes shall be as recessed as possible without the splitting of the components. Refer to Prints for location: CONTRATOR SUPPLIED PARTS FOR CURRENT CONFIGURATION: 1)#U3800 -12Volt (locate in cab on upper partition) 1)#U3805 -Radio Cord Junction Module (locate inside radio compartment) 1)#U3810 -Radio Interface Module /PTT (locate inside center console) 1)#U3815 -Radio Interface/Headset Station (locate @ action wall area) 1)#H3441 -Headset/Mic (Single Ear) 2)#H3442 -Headset/Mic 1)#C38-25 -Jumper Cord 25Ft. 1)#C38-21 -Radio Interface Cord 21Ft. 1)#C38-12 -Jumper Cord 12Ft. 1)#C38-20 -Power Cord 20R. 2)#C3821-05 -Radio Interface Cord 20Ft. 2)#18352G-07 - MS Connector 5 pin For Remote PTT 2)#26553P-01 -Guard PTT 2)#09851P-28 -Switch PTT Dpst 1)#09815P-20 -Electrical Cord For Remote PTT 40Ft. 1)#18900G-01 -Neoprene Washer (Packet of 10) 1)#40071G-04 -Footswitch (locate in action wall area loose) Newport Beach Fire will make the final connections to interface cables to any Two-Way Radios. 165.BOXLITE FLASH LIGHTS: Proposer Initials:syjTfJl City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 79 14-95 165.1 Provide and install PELICAN 941OL Box Lights. Quantity:Two (2) Locate:Streetside rear compartment. Note:Includes 12 volt pre-wire. Configure:Power hot to Chassis battery. 0 N 166.AIR CONDITIONING 166.1 The chassis manufacturer's largest capacity heat/AC system shall be supplied ©N 166.2 A 12V heat/AC system shall be installed.The BTU and CFM ratings on this unit shall be as follows: Heat:42,600 BTU A/C:36,000 BTU CFM:620 ©N 166.3 The drain pan shall be formed from 1/8" ABS plastic sheet and shall be listed (tilted)toward the drain fitting.The Evaporator unit shall be mounted so that the weight of the coil,case and blower assembly does not rest on the pan. Additionally the entire evaporator shall be tilted toward the condensation drain fitting to enhance water flow to the drain hose.The drain hose shall be Y2"I.D.,collapse resistant and fiber reinforced poly- tubing ©N 166.4 Included shall be a central air type system that routes the conditioned air to a minimum of six (6)adjustable vents.One of the vents shall be located directly over the CPR seat.Vents should be capable of being closed off entirely and rotate 360 degrees.When all vents are open the air output at each vent shall be the same plus or minus 10 percent.The minimum output shall be 133 CFM at each vent or a minimum air speed of 27 knots.In addition the unit shall be located as close to the ductwork as possible to minimize resistance.Manufacturer shall provide an access door for easy service and repair of unit.Shall also supply an air intake vent for true air re-circulation ©N 167.AIR CONDITIONING SECONDARY CONDENSOR 167.1 A secondary condenser,dual fan will be provided and integrated into the rear AC system.©N Proposer Initials:c^jrw City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 80 14-96 The condenser will be located under body in a protected position 168.AIR CONDITIONING HOSE 168.1 Air conditioning hose shall be low loss barrier type specifically rated for R134A type refrigerant ©N 169.HEATER HOSE 169.1 The heater hoses shall route from the O.E.M.tie in point to the rear heater core.Hose shall be 5/8 inch ID Nomex brand.This is the identical hose used by the chassis manufacturer.Hoses made from other materials shall not be used because they do not meet Ford Qualified Vehicle Modifiers Program (Q.V.M.) ©N 170.POWER EXHAUST VENT 170.1 Exhaust vent,left rear streetside wall,Cast Products exterior cover,interior louver round. Attwood Turbo 3,000 inline blower,145 CFM blower to be located streetside rear wall. A service access panel will be provided inside the upper rear cabinet. (1)on/off switch to be located in the action area switch panel ©N SUCTION/OXYGEN SYSTEM 171.OXYGEN SUCTION SYSTEM TYPE 171.1 The oxygen and suction outlets installed in the vehicle shall be Ohio Medical Quick Connect style outlets ©N 172.ASPIRATOR 172.1 The manufacturer shall furnish and install an SSCOR on-board suction system.The system shall include a pump,a vented wall- mounted regulator,and a canister holder that accepts most hospital grade canisters.The aspirator shall be accessible for use from the inhalation area per the attached prints ©N 173.VACUUM PUMP 173.1 The pump shall be a oil-less diaphragm pump.The reason for this is to eliminate the need for maintenance.The pump shall be housed in the vehicle in an area to reduce noise.It shall have ©N Proposer Initials:s£)j?7H. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 81 14-97 clinical airflow in excess of 30 LPM (liters per minute) 174.OXYGEN SYSTEM 174.1 Reliability,safety,and ease of operation are essential characteristics of the onboard oxygen system.System design must meet the following minimum guidelines.The regulator (when specified)shall include an integral dial type gauge to monitor the cylinder contents.The line shall be UL approved. There shall be NO connections installed in the line between the regulator and manifold assembly as these create a possibility for leakage.All connections shall be DISS style and shall be specific to the gas being supplied.The completed system shall be tested once it is installed in the vehicle.This test shall be performed at working pressure for a minimum of four (4)hours. After the system has passed the inspection process it shall be capped and tagged per Federal KKK 0 N 174.2 OXYGEN OUTLETS -GENERAL:Each outlet shall be comprised of an "Inlet Box"and a "Latch Plate"as defined herein.The "inlet box"shall be a universal inlet service box with a 165 mm type "K" (3/8") OD Copper inlet pipe stub which is silver brazed to a brass,one piece,(1 5/16")inlet body.The "inlet box"shall be designed specifically for positive pressure gas service and feature a primary and secondary check valve. Each check valve shall be rated at 1,379 kPa (200psi) 0 N 174.3 The "Latch Plate"shall insert into the universal "Inlet Box".The "Latch Plate"is comprised of the outer cover plate and latching mechanism that will define the adapter type/Brand that will ultimately connect the patient to the oxygen system.The outlet cover shall be color coded GREEN in addition to having a clear permanent legend that identifies the gas type.Dual gas specific safety pins shall be integrated in the face of the outlet "Latch Plate"for safety ©N 174.4 Outlet adapter types shall be easily changed by simply removing the "Latch plate"specifically designed for brand "A" to brand "B" without any further plumbing changes ©N 174.5 As with all medical gas outlets specified herein,all outlets shall be hydrostatically tested and cleaned for oxygen service.All medical gas outlets specified herein shall be UL (Underwriters Laboratory)listed and CSA approved.All outlets will be subject to a line pressure of 50 P.S.I.And shall be leak tested at 150 P.S.I.Per Federal specification KKK-A-1822.Pressure drop ©N Proposer Initials:SDJffli City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 82 14-98 across the outlet shall be less than 2.0 P.S.I.,at normal working pressure 175.ELECTRIC 02 CONTROL WITH DIGITAL MONITOR 175.1 Electric switched oxygen with digital read and low pressure warning. Locate on the main attendant panel. • A manual emergency by-pass is to be located on the attend area wall below the attend panel. •Switch to be located in attendant control panel. •System is to include a main cylinder regulator ©N 176.OXYGEN OUTLETS 176.1 Amico Ohio style quick release,Two (2)outlets: •One (1)outlets in ceiling above head end of cot. •One (1)outlet on wall above squad bench @ head end ©N 176.2 Flow meter Integrated,Amvex 0-15 LPM (Tube Style)Replace (1)Standard Oxygen Faceplate •One (1)located in the attendant panel ©N 177.OXYGEN BOTTLE MOUNT 177.1 Install Zico QR-MV Standard 02 Mount or comparable. Locate in M1 exterior compartment.Capable of holding either "M" or "H"tank ©N 178.PORTABLE OXYGEN BOTTLE BRACKET 178.1 ZICO #QR-D-2,single "D"bottle only (strapless) Quantity:Two (2) Note:Install in the curbside module entry step well. ©N 179.OXYGEN WRENCH A wrench designed to fit the main oxygen bottle will be provided. Locate:Cable to wall by large bottle ©N HARDWARE 180.ATTENDANT SAET Proposer Initials:syjfflt. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 83 14-99 180.1 Attendant seat 6 degree high back with built in child seat. One (1)set of three point seat belt set shall be provided for attendant seat. Seat will be mounted on a Steel base with 360 degree swivel and front to rear slide function. 0 181.SEAT BELTS Seat belts shall be installed in the squad bench area for the seated position,and for backboard retention for a secondary patient.These belts shall meet all applicable testing requirements as set forth in the latest federal 'K'specs. One (1)set of Six point seat belt set shall be provided for the primary bench attendant at the head end seating position. One (1)set of Six point seat belt set shall be provided for the second bench attendant at the foot end seating position. One (1)set of Six point seat belt set shall be provided for the CPR seat One (1)set of three point seat belt set shall be provided for attendant seat. ©N 182.I.V.HOLDER 182.1 IV holders,Two (2)positions,Cast products Polished Aluminum, flush mount. Locate:Refer to the provided prints ©N 183.ANTI-MICROBIAL COATED PULL HANDLES 183.1 CURB SIDE ENTRY DOOR GRAB HANDLES:An angled door handle shall be installed on the interior door panel of the curbside entry door.The handle shall be one-piece and shall be constructed of Stainless Steel.The handle shall feature smooth radius corners and flange mounts at each attachment point. Because contamination occurs most often as a result of contact, this feature must be treated with an anti-microbial agent consisting of an inorganic ceramic coating embedded with silver ions.This coating shall be effective against a broad range of microbes including bacteria,molds,algae and fungi ©N 183.2 REAR ENTRY DOOR GRAB HANDLES:Angled door handles shall be installed on the interior door panels of each rear access ©N Proposer Initials:sv&H. City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 84 14-100 door.The handles shall be one-piece and shall be constructed of Stainless Steel.The handles shall feature smooth radius corners and flange mounts at each attachment point.Because contamination occurs most often as a result of contact,this feature must be treated with an anti-microbial agent consisting of an inorganic ceramic coating embedded with silver ions. This coating shall be effective against a broad range of microbes including bacteria,molds,algae and fungi 184.ANTI-MICROBIAL COATED CEILING GRAB BARS 184.1 A grab rail shall be installed in the ceiling as noted below. This rail is to be constructed of stainless steel.Integral stanchions shall be welded into place at fixed points along the length of the rail for attachment to the ceiling.The rail shall attach through aluminum mounting plates that are welded to the module roof structure for strength and durability.Because contamination occurs most often as a result of contact,this feature must be treated with an anti-microbial agent consisting of an inorganic ceramic coating embedded with silver ions. This coating shall be effective against a broad range of microbes including bacteria,molds,algae and fungi. Size:96" Locate:Above the right edge of the cot ©N 184.2 ADDITIONAL CEILING GRAB BARS: Install Two (2) 24"grab bars,(1) on each side of the CPR seat next to streetside wall. ©N 185.BENCH RESTRAINT 185.1 RESTRAINT NET:A detachable net shall be installed at the head of the squad bench. The net shall be a grid of 1 Yz"wide safety web,spaced on maximum centers of 8 inches ©N 185.2 All Restraint Net attachment devices shall be aviation quality and pull strength tested.A 2,000 pound force applied in shear (Horizontally).Detachment of the net shall be done without the need for a removal or installation tool(s).Each device shall feature a cadmium plated steel attachment ring that is forged in ©N Proposer Initials:SVJ&H. Cityof Newport Beach RFP No. 16-24 Emergency Ambulance Medical Vehicle Page 85 14-101 186.1 187.1 188.1 189.1 one continuous ring,without a split or seam.Each device shall be sewn onto the net webbing with a 1 3/4 inch square shaped thread path and diagonal X-shaped thread path to assure web to ring security. Four attachment points: Two (2)at the floor at head of squad bench. Two (2)at the ceiling at head of squad bench 186.SHARPS POCKET Provide and install a,(1),recessed pocket style sharps pocket for a Sage #R1002 sharps container,bright stainless steel. LOCATE:Attendant area back wall 187.CAST PRODUCTS LICENSE PLATE BRACKET Cast products License plate holder with light,rear #CP 30002. Locate:One (1) on LEFT side above the Tread bright area. Note:Install the specified hidden power lock switch in the top of the fixture in lieu of one of the lights 188.MDT MOUNT (1)Mount #DL-TX204-MTU-O / Lund Tilt-Swivel Clamshell mount. Locate:On passenger side forward section of the center console in cab,(reinforce mounting location on center console) 189.FIRE EXTINGUISHER: Amerx brand commercial grade with vehicle mount,5 LB (shipped loose). Quantity: two (2) 190.STEEL NUMBER PLATES Proposer Initials:SV^W. City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle ©N ©N ©N ©N Page 86 14-102 190.1 CUSTOM UNIT NUMBER PLATES:Provide 5 unit number mounting brackets with plates. Three (3)brackets and plates are to be approximately 20" long X 6"tall. Two (2)brackets and plates for the rear are to be half approximately 12" long X 6" tall. Brackets and Plates to be painted Red to match the body paint. Color Code:Sikkens RED FLNA 30006 Contractor to mount unit number plates using 10-24 stainless steel screws and blind panel fasteners as follows: 1/8"Non Corrosive spacers will be provided between the mount plates and the body. One (1) 20" x 6"plate located centered over the opening of the front bumper. !!!This will require a mounting plate installed over the opening. One (1)20"x 6"plate located on curbside centered between the belt line stripe and "FIRE",centered with the lettering above. One (1) 20" x 6"plate located on the street side centered between the compartment opening and "FIRE"centered with the lettering above. Two (2) 12" x 6"plates located on centered the right and left sides of the module rear,centered with "NEWPORT BEACH" ©N 191.SCBA BRACKETS: Supply and (Ship Loose)for customer install. BASIC SWING DOWN MOUNT:SKU QSD LOAD AND LOCK SCBA BRACKET:SKU:KD-ULLH Quantity:Two (2) 0 N PATIENT-HANDLING EQUIPMENT 192.COT FASTENER 192.1 PRIMARY COT MOUNT:Stryker #6370 floor mount,single position,front antlers removable.(Center Mount Position) The mounts shall be set as specified below: ©N 192.2 COT FASTENER MOUNTING METHOD:All mounting bolts shall be 3/8"diameter,socket head cap screws with at least 16 threads per inch.All mounting blocks shall be supplied and manufactured by the cot mount manufacturer.The mounting blocks may protrude above the flooring surface by up to 3/16", ©N Proposer Initials:sVj^t City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 87 14-103 as long as all of the edges are chamfered.The cap screws shall not protrude above the upper surface of the mounting block 192.3 All cap screws shall be through bolted through 1/2 (.500)inch thick,6061-T-6 Aluminum plate structure.All cot plate structure shall be continuously welded to the floor structure members.Bolt tapping is acceptable ONLY over blind areas,where through bolting would require removal of the rear fuel tank AND access has been blocked off by permanent,critical structure or components.Plate tapping shall not be done unless the plate is at least one (1") inch thick.Mounting bolts shall not point toward fuel filler or fuel vent hoses,in accordance with good engineering practices set forth by the Society of Automotive Engineers and Ford's Qualified Vehicle Modifiers'program. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 192.4 Bidders shall meet or exceed mechanical strength described in the minimum fastening method.Material thickness and/or through bolt criteria is mandatory even if the vendor has current certification to A.M.D.Standard 004 utilizing lesser materials. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 192.5 COT POSITION No 1:This cot position shall be set up for a Strvker POWER PRO 6500 cot.Set approximately 8"out from the left side wall cabinet.The longitudinal location shall be set 30 inches measured from the backrest of the attendant's seat (set all the way toward the front of the patient cabin)to the head of the primary cot frame,per current KKK-A-1822 ©N 193.COT SAFETY HOOK 193.1 Install a Stryker Yellow safety hook w / 2"reflective tape on rear door sill. Set up for a Stryker POWER PRO 6500 ©N PAINT,BODY AND GRAPHICS Proposer Initials:SV£M City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 88 14-104 194.PAINT AND STRIPING 194.1 An acrylic urethane paint process is required on the module body.This process shall extend to the chassis if the vehicle converter must perform paint or body work to the chassis.The acrylic urethane process is required so that the highest possible gloss will be provided.Acrylic urethane possesses superior color and luster retention characteristics when compared to other types of paint.In addition,an acrylic urethane process provides a higher resistance to chemical sprays,salt sprays,humidity, and temperature changes.Lastly,this process,given the expected life of the vehicle and its heavy-duty cycle,will best resist chipping.The final paint application shall be free of material application imperfections such as orange peel, streaking,or a dull finish.The final application shall provide a high gloss on all body surfaces including the roof and excluding the underside. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 195.PREPARATION 195.1 100%PAINT FILM COVERAGE:All stages of primer and paint shall cover all surfaces.Hinge mating surfaces on the doors and jambs shall be painted.Bare aluminum and primer only preparation is not acceptable under door hinges.Doors shall be painted without actuation handles installed and doors removed from body.Paint film thickness to be no less than 4.1 mil thickness. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 195.2 PAINT SYSTEM TYPE:The paint shall be Poly-Urethane type ©N 195.3 MECHANICAL ADHESION PROMOTER:The entire module shall be degreased.Degreaser shall be applied to manufacturers'recommendations.Body to be inspected for flaws and imperfections and to assure built to order specifications.All surfaces shall be sanded with 150 grit paper ©N Proposer Initials:sVfffl City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 89 14-105 and all imperfections repaired. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 195.4 CHEMICAL ADHESION PROMOTER:The module shall be hot- water washed at (140 degrees or greater).Then the aluminum Body shall be treated with Alumiprep 33 acid etching followed by a complete body rinse.To ensure all surfaces are cleaned,this step shall be repeated a second time.The entire unit shall be wet coated with Alodine 5700 conversion coating and de-ionized water mixed. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 195.5 PRIMER:Apply 3 coats of BTLV HI Solids Polyurethane.The unit is then baked at 140 degree metal temperature for one hour. Assure minimum at 3 mil thickness.Primer shall be sanded with 360 grit paper to assure flat,orange peel free surface. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 195.6 TOP COAT (PAINT):Entire module shall be degreased. Degreaser shall be applied to manufactures recommendations. Two coats of BTLV High Solids color shall be applied. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards 0 N 195.7 CLEAR COAT:The clear coat shall be manufactured by the same company as the primer and base coat.Three coats of "clear coat polyurethane shall be applied per the manufacturer's instructions. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N Proposer Initials:SV^M City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 90 14-106 195.8 3M POLISHING SYSTEM:Prior to 100%paint cure,the paint on the ambulance body shall be sanded to 1200 grit and polished flat per 3Ms Perfect-It product program for smooth finish. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 195.9 PAINT WARRANTY:The conversion paint shall be warranted to the original owner for a period of 4 years,48,000 miles.The color shift shall be no greater than Delta E of 4.0 with a minimum gloss retention of 60 gloss units at twenty-degree angle. Warranty to include a 36 month Corrosion coverage with no exclusions. Exceptions to this requirement will be considered,provided the exceptions meet minimum KKK Federal Specifications for Ambulances standards ©N 196.CORROSION 196.1 EXTERIOR FASTENERS:All screw sites require a replaceable nylon insert for the fastener to thread into.This will isolate the dissimilar metals.Additionally each hole shall be treated with an Electrolysis Corrosion Control compound prior to installation of the nylon inserts.All exterior screws shall be stainless steel ©N 197.PAINT CONFIGURATION 197.1 CUSTOM RED PAINT SCHEME: Cab to be repainted RED LOWER HALF/WHITE UPPER HALF from 2"below cab door windows and extend onto the first side body line along the upper edge of the hood and turn into the top corners of the chrome grill trim. The top of the hood is to be White. Refer to provided prints. Module is to be painted RED Color Code:Sikkens RED FLNA 30006 Color Code:OEM WHITE ©N 198.REFLECTIVE BELTLINE STRIPE Proposer Initials:SV-dM City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle Page 91 14-107 198.1 White Reflective Stripe,Seven (7)year warranty Single 6"beltline,Mid Body,upward jog on the forward portion of the module. The stripe shall include 5/16 inch Black reflective pinstripe on edges. Refer to prints ©N 199.REAR CHEVRON REFLECTIVE STRIP 199.1 There shall be a rear Chevron reflective stripe set on the flat rear surfaces. The stripes shall be NFPA 1091 compliance. The Chevron stripes shall be 6.00 wide and be in an upside down "V"pattern.The colors shall be Red and Yellow per NFPA 1901 requirements 0 N 199.2 The stripe shall include 5/16 inch Black reflective pinstripe on edges.©N 200.MODULE ENTRY DOOR REFLECTIVE STRIPE 200.1 Install 3"wide Red and White,High Index candy cane stripe. Locate:Stripes along lower edge of inside door panels ©N 201.EMBLEMS 201.1 All emblems shall be of durable weather resistant material ©N GRAPHICS 202.CUSTOM LETTERING (OPTIONAL) 202.1 Proposers shall provide and installthe following graphics and lettering. Laminated Gold Leaf,1"Engine turn,1/8"White borders,Black shadow left. Module Sides: "NEWPORT BEACH"(Straight)5.5 ©N Proposer Initials:ST>£ftl City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 92 14-108 203.1 inches inches "FIRE DEPARTMENT" Other lettering:"PARAMEDICS" Red Reflective Scotchlite Unit Numbers:NPB ### Module Front: "NEWPORT BEACH"(Straight)5.5" center on the front of the module below the light bar. Front of Chassis Hood: "FIRE RESCUE"(Straight)3.5" center on the front edge of the hood above the (Straight)5.5 (Straight)4 inch (Straight)5.5 inch Module Rear: "NEWPORT BEACH" .below the windows "FIRE DEPARTMENT" lower portion of doors Other lettering:"PARAMEDICS" bottom of rear doors White Reflective Scotchlite Black Shadow Left (Straight)4 inch (Straight)4 inch (Straight)4 inch ADDITIONAL LETTERING:White Reflective Scotchlite (Straight) 5.5 inch,Four (4)sets of each Unit Numbers,1 unit "NPB ###" Three (3)sets on single plates for install on the front of the chassis and on the module sides. One (1)set of each on a split pair of shorter plates to be installed on the rear of the module. White Reflective Scotchlite Refer to prints 203.REAR CHEVRON REFLECTIVE STRIPE: There shall be a rear Chevron reflective stripe on the flat rear I Q surfaces. Proposer Initials:SDJtM City of Newport Beach RFP No.16-24 Emergency Ambulance Medical Vehicle N Page 93 14-109 The stripes shall be NFPA 1091 compliance. The Chevron stripes shall be 6.00 wide and be in an upside down "V"pattern. !!!Add translucent Red Electro Cut #1172 background to "NEWPORT BEACH FIRE"and "PARAMEDIC" The colors shall be Red and Yellow per NFPA 1901 requirements. Color:3M Conspicuity Fluorescent Yellow #983-21 Color:3M Electro Cut Red #1172 Note:Black .250"Pin stripe border will be provided between each color stripe. 204.MODULE ENTRY DOOR REFLECTIVE STRIPES: 204.1 Install 2"wide Red and White 3M Tape #983-326,High Index. Locate:Stripes along lower edge of inside door panels. 0 N 205.CUSTOMER SUPPLIED DOOR SEALS 205.1 Install customer supplied cab door seals.Locate:Centered from front &rear door edge.The top is to be even with the body line. Leader to supply &install rock guard material over both cab door seals. ©N 206.INTERIOR/EXTERIOR LAYOUT DRAWINGS 206.1 Proposer shall refer to Appendix A for a complete set of interior/exterior layout drawings ©N Proposer Initials:spjffl. City of Newport Beach RFPNo.16-24 Emergency Ambulance Medical Vehicle Page 94 14-110 Newport Beach Fire Type 12015 96" X 173" Module on Freightliner 175" WB chassis,72"Headroom Whelen M9 Series LED Red Warning lights w/ChromeFlange Kussmaul20Amp SuperAuto Eject Shoreline (Redcover) Wlielen M7D Series LED Split Red/Clear Warning w/'Chrome Flange Chrome Air Horns (Aproximate Location) 4" Droppan Floor 8" Forwardsection only Note:All dimensions are approximate and subject to change. Wlielen M9ZCSeries LED Gear Scene lights Wlielen M9 Series LED Red Warning lights w/ChromeFlange Red Marker Light (2) Adj. Shelves Red reflector Doors to open over center CustomAluminum Rubrails (U Channel) 10941 \Afeaver Ave., So. El Monte, CA 91733 phone.(626)575-0880 VIEW:Streetside Exterior Drawn By:Jorge M.Date:July-2015 LE-#1 I*lehder EMERGENCY VEHICLES 14-111 Newport Beach Fire Type 12015 96"X 173"Module on Freightliner 175"WB chassis,72"Headroom Red Marker Light Wlielen M9 Series LED Red Warning lights w/Chrome Flange CustomAluminum Rub rails (U Channel) Wlielen M9ZCSeries LED Clear Scene lights Alcoa polished aluminum wheels Note:All dimensions are approximate and subject to change. Wlielen M9 Series LED Red Warning lights w/Chrome Flange Diamond Plate Running Boards Wlielen M7D Series LED SplitRed/Gear Warning w/Chrome Flange ChromeAir Horns (Aproximate Location) 10941 v\feaver Ave., So. El Monte, CA 91733 phone.(626)575-0880 VIEW:Curbside Exterior Drawn By:Jorge M.Date:July-2015 i p- #?I][jgLEnnEH I—I—ITC—|| "EMERGENCY VEHICLES 14-112 Newport Beach FireType 12015 96" X 173" Moduleon Freightliner 175"WB chassis,72"Headroom Wlielen M7 Series LED RedSteady Warn in w/Chrome Flange Wlielen M9 Series LED, Red Warning lights w/Chrome Flange DavidClark U3800 (Inside cab on Headliner) Wlielen BrowLight (Wlielen Pioneer #PFP2 Dual Flood Pioneer Plus) Federal 200 W SirenSpeaker for EQ2B siren Note:All dimensions are approximate and subject to change. Whelen M9 Series LED Clear Scene lights w/ChromeFlange GTT794H Opticom Amber Marker Lights w/Chrome housings (On Body) David Clark H3441 and H3442 (Inside cab on partition wall) Wlielen M7 Series LED Red Warning lights w/ Chrome Flange Flash in Xpattern Federal 100 W Siren Speaker for Wlielen Siren 10941 \Afeaver Ave.,So.El Monte, CA 91733 phone.(626)575-0880 VIEW:Front Exterior Drawn By:Jorge M. Date:July-2015 LE-#3 L,lehder EMERGENCY VEHICLES 14-113 Newport Beach FireType 12015 96"X 173"Module on Freightliner 175"WB chassis, 72" Headroom Wlielen M7Series LED Red Warning lights w/Chrome Flange Wlielen M9 Series LED Red Warning lights w/Chrome Flange Back Up Camera Exhaust Vent Drip rail Wlielen M6TSeries LED Amber Turn w/Arrow Wlielen M6BUWSeries LED ClearScene Back Uplights Red reflector LEADER Style (Docking) Flip-up Step Bumper Wlielen M6ZCSeries LED ClearScene lights w/Chrome Flange Red marker lights (W/Housing) Wlielen M9 Series LED Red Warning lights w/Chrome Flange Wlielen TAM85Amber TrafficAdvisor Wlielen M9 Series LED ~~Amber Warning lights w/Girome Flange Wlielen M6 Series LED Red Warning lights Wlielen M6BTTSeries LED 'RedBrake/Tail lights Wlielen UM6FCV4 Chrome Flange Red reflector Mudflaps w/ leader plate Recessed cast products License plate holder 10941 Weaver Ave., So. El Monte, CA 91733 phone.(626)575-0880Note:All dimensions are approximate and subject to change. Drawn By:Jorge M.Date:July -2015 |LE-#4 |HVIEW:Rear Exterior Lehdeh EMERGENCY VEHICLES 14-114 Newport Beach Fire Type 12015 96"X 173"Module on Freightliner 175"WB chassis,72" Headroom Exhaust vent. 6"Deep Cabinet Sliding piex doors Glove Box Storage Plex door Compartment LED Strip lights inside all compartments Open countertop storagefor monitor Hinged restocking windows (13"H I.RAproxx) (2)Recessed 6' Aluminum Drawers12"Deep w/laminatedaluminumface w/Locking Chrome "D"ringlatches and7/8"locks Note: All dimensions are approximate and subject to change. Gibraltarcounter tops Hinged restocking windows (13"H I.RAproxx.) Wood door w/NON locking 7-Position Switch inside comp. Wood door w/NON locking latch and (1)adj.shelf (Make cabinet as wideaspossible) David Clark U3805 (InsideRadio comp.) Fixed Shelf Radio Compartment 10941 Weaver Ave., So. El Monte, CA 91733 phone.(626)575-0880 VIEW:Street wall Interior Drawn By:Jorge M.j Date:July -2015 LE-#5 L lehder EMERGENCY VEHICLES 14-115 N e w p o r t B e a c h F i r e T y p e 1 2 0 1 5 A c c e s s t o p o w e r d i s t r i b u t i o n w / l o c k i n g l a t c h A t t e n d a n t s e a t " S e w n ' o n S w i v e l B a s e w / B u i l t i n C h i l d s e a t w / 3 P o i n t S e a t b e l t H i n g e d w o o d D o o r w / C h r o m e " D " r i n g l a t c h ( D o o r f o l d s i n t o s i d e o f A L S ) 9 6 " X 1 7 3 " M o d u l e o n F r e i g h t l i n e r 1 7 5 " W B c h a s s i s , 7 2 " H e a d r o o m ( 2 ) 1 1 0 V . O u t l e t s L o c k i n g D r u g c o m p a r t m e n t R e c e s s e d m o u n t w / f l a n g e K N O X 5 5 2 0 D r u g V a u l t w / W I - F I M i s c . S t o r a g e T o p H i n g e d P I e x D o o r 6 " T a l l a l u m i n u m d r a w e r w / l a m i n a t e d a l u m i n u m f a c e w / c h r o m e l o c k i n g " D " r i n g l a t c h C l o s e d t o i n t e r i o r O p e n t o e x t e r i o r ( L e a v e 2 2 1 / 2 " f r o m b o t t o m o f c o m p a r t m e n t t o b o t t o m o f d r a w e r ) ( 2 ) 3 / 8 " P l e x i g l a s s d o o r w i t h C h r o m e f T D n r i n g l a t c h e s ( 2 ) L E D S t r i p l i g t h s I n s i d e a c c e s s t o j u m p g e a r . ( 2 ) A d j u s t a b l e s h e l v e s W i t h G i b r a l t a r l i p s t o i n t e r i o r N o t e : A l l d i m e n s i o n s a r e a p p r o x i m a t e a n d s u b j e c t t o c h a n g e . 1 0 9 4 1 W e a v e r A v e . , S o . E l M o n t e , C A 9 1 7 3 3 p h o n e . ( 6 2 6 ) 5 7 5 - 0 8 8 0 L e h d e h V I E W : B u l k h e a d w a l l I n t e r i o r D r a w n B y : J o r g e M . D a t e : J u l y - 2 0 1 5 L E - # 6 I S E M E R G E N C Y V E H I C L E S 1 4 - 1 1 6 1 4 - 1 1 6 Newport Beach Fire Type 12015 96"X 173"Module on Freightliner 175"WB chassis,72" Headroom Integrated Flow meter OxygenOutlet (Tubestyle) 5 min. Re-stocking Timer (RELOCATED) Add Wlielen Door Marker Lights (Flashing) Defeat Switch (2)ZicoQR-D2 Bottle holders Trash Container. (Red Plexiglass Lid) Sharps Container Kendall 8507SA'' (L#04-011; 3/8"Plexiglas Top Hinged doors w/gas strut hold open w/Chrome "D"ring latches 73/8"Wx 121/4"L Tote storage 6" deep (6)adjustable vertical dividers with 3/4 "front retaining lip nside Access to Exterior Compartment 6-Point Seat belt restraints 3/8"Single Plex. door w/Chrome "D" ring latches top and bottom CUSTOM CABINET: Uppersection open w/1/3 Height Plexface Midsection 3/8"NON locking plexi door w/(2)adj.shelves Lowersectionstoragefor IVcatheters w/(4)removable plexi dividers Note:All dimensions are approximate and subject to change.10941 Weaver Ave., So. El Monte, CA 91733 phone. (626) 575-0880 Drawn By:Jorge M.Date:July -2015 LE-#7 |MlVIEW:Curbside Interior LEHDER EMERGENCY VEHICLES 14-117 NewportBeachFireType12015 96"X 173"Module on Freightliner 175"WB chassis,72" Headroom Electric door lock switch (wiredto OEM) Dome &Scene defeat Switches Add Wlielen Door Marker Lights (Flashing) 2"Red/Wliite Reflective AirDump doorswitch Wired toLeft (Driver)Door 10941 Weaver Ave., So. El Monte, CA 91733 phone.(626)575-0880Note:All dimensions are approximate and subject to change. Drawn By:Jorge M.|[Date:July -2015 LE-#8 |B emergencyvehiclesVIEW:Rear Interior 14-118 Newport Beach Fire Type 12015 OEM Climate controlpanel Digital Volt meter Digital Amp.meter EQ2B Siren Emergency Start Switch Radio head w/Bezel Cup holders Console to be texture painted aluminum 12 V Outlet 96"X 173"Module on Freightliner 175"WB chassis,72" Headroom MDT MountingArea (Reinforced) CUSTOM CONSOLE Knox Key Secure Whelen 295 HFSA-7Ca.Spec. w/Remote Amp. David Clark Push to Talk Traffic Advisor (2) Dual Port USB Charger DavidClark U3810 (Inside Center Console) (2) Portable Radio Chargers Note:All dimensions are approximate and subject to change 10941 V\feaver Ave., So. El Monte, CA 91733 phone.(626)575-0880 LehderVIEW:Cab Console.Drawn By:Jorge M.j Date:July -2015 | LE-#9 I EMERGENCY VEHICLES 14-119 NewportBeachFire Type 12015 96"X173"Module on Freightliner 175"WB chassis,72"Headroom IntegratedFlowmeter Amvex 0-15 LPM (Tube style) LEDStrip Lighting RecessedSharps holder Emergency bypass Electric 02 Digital monitor SSCOR Suction "s Single row 10 -Switch panel A= DOMEON B=DOME HI-LO,ON /ON C=BLANK D=EXHAUST VENT-3 WAY E= SUCTION F=A/C0N G=A/C FAN HI-LO H=A/C HEAT/COOL 1=BLANK J=BLANK DavidDark U3801 (Action Wall Area) David Clark H3442 (Action Wall Area) Kussmaul Inverter Remote Panel Beamis Suction Container Dual USB Charger 110 V. Oulets 14"Widex 12"deep cabinet with Hinged plex doors and 2 adjustable shelves with Chrome "D"ring latches Note: All dimensions are approximate and subject to change. VIEW:Switch Panel I Drawn By:Jorge M.|Date:July-2015 10941 Weaver Ave., So. El Monte, CA 91733 phone.(626)575-0880 LE-#10 LEHE1ER EMERGENCY VEHICLES 14-120 Newport Beach Fire Type 12015 96"X 173" Moduleon Freightliner 175"WB chassis,72"Headroom Stryker #6370 Floor mount 73/8,,Wxl21/4"L Tote storage 6" deep Note:All dimensions are approximate and subject to change. sen ( Wise Seat V ] 3^: Sharps Container Kendall 8507SA (L#04-011) Trash Container (Red Plexiglass Lid) ~X£\ 3BV 10941 Weaver Ave., So. El Monte, CA 91733 phone. (626) 575-0880 VIEW:Overhead Floor Drawn By:Jorge M.|Date:July-2015 | LE-#1 I I*LEHOER EMERGENCY VEHICLES 14-121 NewportBeachFireType12015 24"S/SAntimicrobial Grab Bars IV Hook Position 3 96"X 173"Module on Freightliner 175"WB chassis,72" Headroom IVHook r^„:i:„n /i->Postal Ceding 02 Outlet 96"S/SAntimicrobial Grab Bar (8) Wlielen LED Dome Lights GPS Antenna (2)Antenna Leads w/Cover plates Note:All dimensions are approximate and subject to change.10941 VAfeaver Ave., So. El Monte, CA 91733 phone.(626)575-0880 VIEW:Module Ceiling Drawn By:Jorge M.||Date:July-2015 LE-#12 L Lehdeh EMERGENCY VEHICLES 14-122 Newport BeachFire Type 12015 96"X 173"Module on Freightliner 175"WB chassis,72"Headroom OVERHEAD SWITCHING . jl I SWITCHES A-PRI -SEC - LIT RED/AMBER LED B-HEAD LIGHT FLASHER - LIT CLEAR LED c-OPTICOMDEFEAT d-BROWLIGHTSWITCH E-BACK UP ALARM MOM.ON -NON LIT F-LEFT SCENE - LIT WHITE LED G-REAR SCENE -LIT WHITE LED H -RIGHT SCENE -LIT WHITE LED I -PATIENT DOME 3 WAY ON-ON - LIT AMBER LED J-PATIENT A/C 3 WAY ON-ON - LIT BLUE LED K-EXHAUST-3 - WAY UTAMBER LED L-MODULE DISCONNECT - LIT GREEN LED PILOT LIGHTS M.PILOTLIGHT-PARKING BRAKE LED N.PILOT LIGHT-RED DOOR OPEN LED O.PILOT LIGHT -RED EMERGENCY START LED P.PILOT LIGHT -AMBER LOW VOLTAGE LED Q. PILOT LIGHT -GREEN MASTER ON LED HCESanStBLBtSnilffl _Q Note:All dimensions are approximate and subject to change.==^_ VIEW:Switches,Pilot lights and Meters Drawn By:Jorge M.Date:July -2015 |LE-13 10941 Weaver Ave., So. El Monte, CA 91733 phone.(626)575-0880 IS Lehoer EMERGENCY VEHICLES 14-123 NewportBeachFireType12015 96"X173"Module on Freightliner 175"WB chassis,72" Headroom Note:All dimensions are approximate and subject to change. VIEW:Graphics,Lettering NEWPORT BEACH FIRE DEPARTMENT n 10941 Weaver Ave., So. El Monte, CA 91733 phone.(626)575-0880 Drawn By:Jorge M.Date:July-2015 LE-#14 L Lehder EMERGENCY VEHICLES 14-124 *Remote PTT Requires: •0[J851P-25 =PTT Switch 18900G-36 = Neoprene Washer 26553P-01 =Switch Guard •09815P-20HA000 = 2 Cord conductor 18352G-07 =MS Connector Made In USA C3821-05: temote PTT -< U3810 •M-anuWMIi-xwu _J CO ta T U380O C38-12 r-wjlowi j (—nwm—i [—mm-1 I mil—( I imi—I imnir I o o 3 Position Wired Intercom System Prepared for Newport Beach Fire Project:New Ambulance Layout .' > "Remo PTT David Clark WWW.DAVIDCLARK.COM 14-125 EXHIBIT B PRICING PROPOSAL Halcore Group,Inc., DBA Leader Industries Page B-1 14-126 Leader EMERGENCY VEHICLES 10941 Weaver Avenue South El Monte,CA 91733 Steve De La Montanya,Sales Representative Mobile:(707)529-7522 Fax:(707)546-1070 QUOTATION 16-Feb-2016 City of Newport Beach 3300 Newport Blvd Newport Beach,California,92658. TE RMS COD FOB FOB:Newport Beach.CA SHIP VIA Ground Pricing QUANTITY DESCRIPTION EACH EXTENDED AMOUNT ! !•1 1 I 1 1 1 1 1 ! 1 1 1 2016 Freightliner M2 -LEADER/HALCOR Custom Ambulance Multi Unit Discount:(Two or more vehicles build consecutivelyS3,000.00) Leader CA customer Discount: Pre-Construction Conference Travel Costs:Leader South El Monte Mid-Construction Conference Travel Costs: Final Inspection Conference Travel Costs: Delivery: Delivery to Newport Beach,CA CA Tire Fee $1.75 (Per Tire) Sub-Total Sales Tax 8.00%(Newport Beach) Estimated DMV Fees N/A Exempt. TOTAL QUOTED AMOUNT $250,862.00 $ $(4,000.00) $ $ $ $100.00 $12.25 $250,862.00 $ $(4,000.00) $ $ $ $100.00 $12.25 $246,974.25 $246,974.25 $19,757.94 $ $ S 19,757.94 $ $ $266,732.19 $266,732.19 Estimated Delivery:210 Days from reciept of signed order. Customer Approval:Payment:(Please check one) Leasing I—I Company Check L_l Wire Transfer 1 1 Signature 2/2/2016 Date THANK YOU FOR YOUR BUSINESS 14-127 Rev.12/18/14 Customer Sales Order LEHDER RmeuLflncE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 Newport Beach Fire 707-529-7522 Itemnumber Description 10. 10.1 Prep modular and misc 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan 10-BASE SECTION 10.52 LI96-169" Ford Type III w/72"headroom,(H)Base Conversion (949)644-3363 Custome, 1559 VIN Number Parent Job 1559 $111,256 10. 800 SPECIAL:$82,914 Freightliner M2106 CONVENTIONAL CHASSIS:2016 106 INCH BBC FLAT ROOF ALUMINUM CONVENTIONAL CAB CUM ISB 6.7-280 280 HP @ 2300 RPM,2600 GOV, 660 LB/FT @ 1600 RPM Cummins Exhaust Brake IntegralWith Variable Geometry Turbo With On/Off Dash Switch,Activates Stop Lamps. ALLISON 2200 EVS AUTOMATIC TRANSMISSION WITH PARK PAWL WITH PTO PROVISION (1)DENSO HEAVY DUTY AND (1)SANDEN COMPACT REFRIGERANT COMPRESSORS DETROIT DA-RS-17.5-2 17,500#R-SERIES SINGLE REAR AXLE AIRLINER 12,000#REAR SUSPENSION DETROIT DA-F-10.0-310,000#FF1 71.5 KPI/3.74 DROP SINGLE FRONT AXLE 10,000#TAPERLEAF FRONT SUSPENSION AIR BRAKE PACKAGE 4425MM (174 INCH)WHEELBASE EXPECTED GROSS VEHICLE WEIGHT CAPACITY:22000.0 lbs NOTE:3 BATTERIES ATTACHED TO FRAME RAIL TO BE LOCATED IN THE CONVERSION. OEM ALUMINUM WHEELS (4)OUTER WHEELS TO BE ALCOA POLISHED ALUMINUM,THE REAR INNER WHEELS,PAINTED STEEL. NOTE:NO SPARE TIRE OR WHEEL INCLUDED WITH THIS CHASSIS. REFER TO PROVIDED CHASSIS SPEC 20 -PRETAX 20. 20.1 Document Processing Fees 30. 40. 40 -COMPLIANCE 40. 20 Customer supplied itemsto be INSTALLED: 1559 2014 Database 2/2/2016 Page 1 of 28 14-128 LEHDER HITIBUUinCE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customa 1559 707-529-7522 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description Note:See # 5250 (2)CUSTOMER SUPPLIEDPORTABLE RADIOCHARGERS See #7220 INSTALL CUSTOMER SUPPLIED RADIO HEAD &CABLES See #7260 INSTALL A CUSTOMER SUPPLIED KNOX KEY SECURE See #7270 INSTALL CUSTOMER SUPPLIED GPS ANTENNA LEAD See #11260 INSTALL CUSTOMER SUPPLIED CAB DOOR SEALS 40.100 SPECIAL: PerformancBond:$1,718.00 51 -CHASSIS ITEMS OPTIONS 51. 51. 15 Fuel,fill fueltank. (E450Gasoline) Note:Freightliner M2,Fill with Diesel Fuel. 51.100 SPECIAL: CAB TO MODULE CRAWL THROUGH OPENING: (HEV) 51.110 SPECIAL: AIR HORN FOOT SWITCH: -Secure drivers side air hom switch in position identified (footrest) -Secure passenger side air hom switch up under dash ina out of the way location, (switch willnot be used) 51.130 SPECIAL: LIQUID SPRINGS: LiquidSpring conversion at Utility Body Werks in Elkhart Indiana. NOTE:Included in chassis price. (HEV) 51.140 SPECIAL: SHOP MANUALS:One (1) complete set of Chassis, Engine, and Transmission Shop manuals on CDor DVD. Note: Ship loose with thevehicle. 60 -MODULAR BODY ITEMS -STANDARD 60. 60.1 ModularDimensions:96"wide x 169" longx72" Headroom Note:FREIGHTLINER BODY:106"Cabaxle96"x 173"body. 60.2 The module body shall be constructed to provide a minimumfifteen (15) year warranty. 60.3 Module bodyshallhave an addition (5)year warrantywhen remountedbyan approved remount facility. 60.4 The corner post shall be extruded aluminum (6063-T5 alloy). 60.5 The roof corners shall be extruded aluminum (6063-T6 alloy). 60.6 The exterior wall and roof tubes shall be min (2) inch square with min .125 wall thickness, located on twelve (12) inch centers. 60. 7 Inaddition to the verticalwall supports there shall be a horizontalbeam, located inthe beltline area. 1559 2014 Database 2/2/2016 Page 2 of 28 $1,718 $225 $2,650 $787 $5,200 14-129 LEHDER **»« HmeuinncE Steve De La Montanya 707-529-7522 10941 Weaver Avenue South El Monte,CA 91733 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customa • 1559 (949)644-3363 Itemnumber Description 60.8 Gusset supports shall be provided. 60.9 The exterior body panels shall be 5052-H32 alloy. 60. 10 The thickness required forexterior body panels is: -Side,front,and rear walls:.125 -Roof and Floor panels:.090 60.11 60.12 Floors shall be aluminum beams covered byaluminumsheeting, then 3/4 inch plywood. All exterior aluminum bodypanels shallbe attached to the structuralsupports viahigh performance polyurethane two sided tape. 60. 13 Each bodypanel shallbe welded to horizontal frame members, roofextrusions, and vertical corner posts. 60. 14 The door skin and edges shall be formed froma single sheet of aluminum 60.15 Outer Door panels are aluminum .125 aluminum. 60.16 Each door shall include an internal extrusion for added reinforcement. 60. 17 An inner door pan shall fitflush withthe inner edges of the door. Note:See Item #61.500 60. 18 All module doors shall incorporate an extruded rubber seal located around the perimeter of the door. 60.19 All doors shall have full-length stainless steel hinges. 60. 20 All doorjambs must incorporate an extrusionthat is overlaid bythe body skin. 60. 21 Side door and compartment doors shall have gas-filledhold opens. Rear doors shall have grabber style devices. 60.22 60.23 60.24 60.25 60.26 The entire exterior handle assembly shall be Tri/Mark Series 2200 cast metal that is chrome plated and buffed to a high luster. Rear entrance doors shall be equipped withmanual safety release latches at top and bottom of doors. Must havo full soattravol in tho cab.A minimum 6"rocoss shall bo designed into tho front bulk head wall of tho modulo body to accomplish this. Note: N/ATYPE 1 CHASSIS,OEM seat travel. Aminimumof(5)five Mounting platformsshall be attached along the chassis frame rail for a total of (10)ten. Each ofthe module body access doors shall include window cut-outs. 1559 2014 Database 2/2/2016 VIN Number Parent Job 1559 Page 3 of 28 14-130 LEADER nmBULflncE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customer 1559 707-529-7522 (949)644-3363 Itemnumber Description 60. 27 Stainless steel splash shields installedon the lowerfrontface ofthe module bodyjust aft of the cab access doors. 60.28 Polished stainless steel fender flares installed around each wheel well opening. 60. 29 Polishodstainloss lowerbodyrubrails installed on each side ofthomodule body. Note:See Item #61.520 60. 30 Rear kickplate made out of polished aluminumDiamondplate 60. 31 (4)Aluminum diamondplatecorner caps-14"high 60. 32 DropSkirt,Curbside forward w/(2)step entry 60. 33 Aluminum Drip Rails, mounted over exterior compartments and access doors. 61 -MODULE ITEMS -OPTIONS 61. VIN Number Parent Job 1559 61.500 SPECIAL:$250 EXTERIOR COMPARTMENT INNER DOOR PANELS: Delete Diamond Plate and replace with the following: The exterior compartment innerdoor panels are to be .125" flatplatealuminum witha 180 DA finish ILOS. (HEV) 61.510 SPECIAL: COT MOUNT REINFORCEMENT PLATES:Power Load Additional under floor reinforcement is required for future installationof a Stryker Power Load system. (HEV) 61.520 SPECIAL: CUSTOM ALUMINUM RUB RAILS: Install Polished Aluminum U channel skirt rub rails ILOS. (HEV} 67 -EXTERIOR COMPARTMENTS -STANDARD 67. 67.1 All exterior compartments will be constructed out of polished aluminum diamond plate 67.2 M1-STREETSIDE FRONT COMPARTMENT Door Opening: This area shall be accessed through a single outside hinged door. The compartment shall house the vehicle's primary 02 cylinder. Vertical track for mounting of a QRM-V 02 bottle mount shall be welded on the #2 wall of the compartment The compartment shall be vented to the outside. (See drawings for compartment sizes) 1559 2014 Database 2/2/2016 $250 Page 4 of 28 14-131 LEADER HITIBULflnCE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Custome, 1559 707-529-7522 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description 67.3 67.4 67.5 67.6 Note:CORRECTED STREETSIDE FRONT COMPARTMENT (#M1) Door Opening:70.5"High x 22"Wide x 20.5"Deep A fixed divider 8"tothe right ofthe#1 wall inthe compartment,andadd strap w/quick release. The 14"wideareato the rightofthe dividerwill be forthe main02 storage. Locate unistrut trackon back,#2 wall,rightcomer to mountthe standardZico02 hardware. This area shallbe accessed through a single outside hinged door. Referto options,68.130.68.150.68.170.68.180 M2-STREETSIDE INTERMEDIATE COMPARTMENT This area shall be accessed through a pair of hinged doors Thiscompartmentshall have (1)adjustable shelf (See drawingsforcompartment sizes) Note:CORRECTED STREETSIDE INTERMEDIATE COMPARTMENT(#2)Corrected dimensions for Freightliner conversionwith12"raiseselected below. Door Opening:41.38"High x 51.5"Wide x 20.5"Deep. Locatethe selected inverter/charger onthe rightwallofthis compartmentnextto the batterystorage drawer.. Refer to options.68.260 _____ M3-STREETSIDE REAR COMPARTMENT This area shall be accessed through a pair of hinged doors. Thiscompartmentshall have (2)adjustable shelves above spare tire. This compartment will house spare tire and changing tools. (Thiscompartment will have a 3"drop pan) (See drawings for compartment sizes) Note:CORRECTED STREETSIDE REAR COMPARTMENT (#3) DoorOpening:63.5" Highx 34"Wide x 20.5" Deep This area shall be accessed through a pairof hinged doors. IllNote:The doors are to open over center to provide a full clear opening. Refer to Options,68.340,68.370,68.380 Selected below. Delete spare tire mount M4-CURBSIDE REAR COMPARTMENT This area shall be accessed through a single hinged door. This compartment will house 72"backboards on the leftside, and stairchair on the lower right side. Thiscompartment will have a vetrtical divider,w/(2)adjustable shelves above stairchair location. NOTE:This compartment requires that the aluminum diamond plate door panel have a pocket for stairchair clearance. Supply(2)sets ofvelcro straps and footman loops, (1)forbackboards, and (1)for stairchair. (See drawings for compartment sizes) Note:CORRECTED CURBSIDE REAR COMPARTMENT (#5) DoorOpening:Full Heightx 25.5"Wide x 20.5" Deep This area shall be accessed through a single of hinged door. Note:Withthe added compartmentdepth,the aluminumdiamond platedoorpanelpocketfor stairchair clearance not needed. Refer to Options 68.460.68.470.Selected below. M5-CURBSIDE FORWARD COMPARTMENT The area shall be accessed through a single hinged door. This shall also be accessible from the vehicle interior front ALS area. (See drawingsforcompartment sizes) Note:CORRECTED CURBSIDE FRONT COMPARTMENT (#7) Note 22" wide full height, no lower battery compartment Interiorwidth approximatly 26" See option 68.650,68.660 1559 2014 Database 2/2/2016 Page 5 of 28 14-132 LERDER **»« RfTIBUUinCE Steve De La Montanya 707-529-7522 10941 Weaver Avenue South El Monte,CA 91733 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customs • 1559 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description 67.7 M6 CURBSIDE FRONT (LOWER)COMPARTMENT This compartment shall bo occossod through o singlo hingod door. This comportmont noods to bo vented,itwill house (2)batteries mounted in a slide out tray. (Soo drawings for compartment sizes) Note:NA/Freightliner conversion. 68 -EXTERIOR COMPARTMENTS -OPTIONS 68. 68.50 SPECIAL: COMPARTMENT DOOR SILL PROTECTION: Install Stainless Steel protection plates on lower edge of exterior compartments. (All Compartments) 68.100 STREETSIDE MOST FORWARD COMPARTMENT: 68. 130 Addan adjustableshelf Note:To the rightofthe fixed divider,above the main02. II!Shelf to have 1"up turned lips. III Shelfstrutto start52"abovethe floor andextendtothe compartment ceiling. 68.150 Add a fixed vertical divider. Note: Locate:8"to the rightofthe #1 Leftwallto provideclearance forthe Zico 02 bracket to the rightof the divider. 68. 170 SPECIAL:$160 DROP PAN FLOOR: Installa 4" drop pan in the 8"wide forward section to accomodate a 72" tell Miller Board storage forward of the divider. (HBO . 68.180 SPECIAL: STRAP SET: Provide and instell a 1"strap set with quick release clip. Locate:Mid level from the front wall to the center divider. 68.200 STREETSIDE INTERMEDIATE COMPARTMENT: 68. 230 Addan adjustable shelf Note:The standard shelf is to be set just above the battery storage area. Locate:Center the added shelf in the space above. $210 $192 $209 $42 $208 68. 260 SPECIAL:$298 BATTERY STORAGE:FABRICATE AND INSTALL ROLL-OUT BATTERY TRAY ON 150-300LB ACCURIDE SLIDES. Note:SIZE FOR 4 BATTERIES. Locate: Inthe forward portionof the Streetside intermediate compartment at floorlevel. Locate:The Inverter/charger on the floorrearward of the battery tray. Note: Lower the standard shelf to just above the battery area to provide protection. Referto option#7200 68.300 STREETSIDE MOST REARWARD COMPARTMENT: 68.370 SPECIAL: COMPARTMENT DEPTH MODIFICATION: Upper24.5"section above 42"willbe 14"deep. 6.5"deep Interior cabinets will back to the upper portionof the compartment (HEV) 68.380 SPECIAL: 1559 2014 Database 2/2/2016 $235 $255 Page 6 of 28 14-133 2/2/2016 Newport Beach Fire Customer 1559LEADER nmBULflncE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 707-529-7522 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description TOOL MOUNTING PLATE: Installa pairof Unistrut style shelf track on the back wall,upper 24.5" portion. Configure: Run the strut horizontally 4" in from the upper and lower margins of the instell area. Bolt a .250"brushed aluminum plate on the unistruttrack. This will be used for install ofSCBA hardware. 68.390 SPECIAL: CUSTOM DOOR HOLD OPEN MOUNTS: The door hold opens are to be positioned to allow the doors to open over center providing access to the full compartment opening 68.400 CURBSIDE MOST REARWARD COMPARTMENT: 68.460 SPECIAL:$192 Add a fixed vertical divider Quantity:One (1) optional, Note unit has One (1) standard, Locate:The standard full height divider 11"to the rightof the left wall. Locate:The optional 40" talldivider 9.5" to the rightof the full height fixed divider. Referto prints. 68. 470 SPECIAL:$192 Add an adjustable shelf: Note: Quantity:One (1) optional, and Two (2)standard,Total (3)Three Locate: To the rightof the fixed divider,the bottom shelf willbe fixed 40"above floorlevel,the other 2 will be distributed above. Referto prints. 68.600 CURBSIDE MOST FORWARD COMPARTMENT: 68. 650 SPECIAL:$142 CUSTOM MODIFICATION TO DOOR HOLD OPEN SYSTEM: Curbside Forward Compartment, delete gas strutholdopen, and replace with a Cast Products hold open device. Door is to open as far as possible without conflicting with the cab passenger door. III NOTE:BODYAFFECTSBODY BUILD ORDERIll 68.660 SPECIAL: CUSTOM MODIFICATION TO SHELVING CONFIGURATION:Do not extend the module floor into the bulkhead cabinet Referto option 2250 69 -CHASSIS - MODULAR MODIFICATIONS @ LEADER -STANDARD 69. 69.1 All exteriorcompartmentsshallhave blackrubber matting on compartmentbottomsand shelves 69.2 Interior LED Lighting inallexteriorcompartments with the exceptionofbattery compartment,(2)verticle LED strip lights from top to bottom located on back side of door jam. 69.3 Cab Running Boards, polished aluminum diamondplatew/star punched safety grip running boards with mud flap. Note: Freightliner Style cab step entry: Two steps,Fuel tank cover under drivers door,Exhaust cover under th passenger door. {HEV) 1559 2014 Database 2/2/2016 Page 7 of 28 $300 14-134 LERDER HfTIBULHnCE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customei • 1559 707-529-7522 (949)644-3363 Itemnumber Description 69.4 Recessed license plate holder (Cast Product)w/LED light(See Printfor Location) 69.5 Install individual rear mud flaps behind each set of rear wheels. 69.6 All patientcompartmententrydoorsshallhave red reflectorsinthe lowercorner (interior) 69. 7 Exteriorof modular shall have rectangular reflectors,amber inthe lower corners infront, red in lower corners in rear 69. 8 Power activated door locks installed on patient compartment access doors, activated by cab (OEM)door lockswitches, and patientcomp.access door lockswitches - mountedin bezels 69. 9 Stainless stool DOTapproved whoolinserts shall bo installed on oilfour outside wheels of the chassis. 69.10 Stainloss stool filler extensions will bo installed on roar whools. 69.11 Install(2)towhooks under rear ofvehicle,attach to bumper frame 69.12 The rear of the vehicle shall be equipped with a (Docking)step/bumper assembly.The center section ofthe rear step bumper shall be constructed of aluminum w/star punched safety grip, and hinged to assist in patient loading. 69.13 Install Fixed windows in the (2) rear patient access doors, and (1) sliding window inside access door.All (3)windowsshall feature a dark privacytint 70. 200 -INTERIOR CABINETS -STANDARD A. 1 A1:Streetside lower cabinet,exterior Stainless Steel riser,CPR section w/storage below w/ hinged lid&holdopen gas strutw/FlexDraw holddown latch,w/Gibraltercounter top. Note:See Item #9010 A. 2 A2:Streetside upper rear cabinet, solidwallwith(1) upper storage area w/sliding polycarbonate doors, w/adjustable shelf. Note:See Item#2200 A. 3 A3:Streetside storage cabinet,(1)upper and (1) lower storage area w/ sliding polycarbonate doors, w/adjustable shelf inupper cabinet only.Center section open w/ Gibraltar countertop. Note:See Item#2230 A. 4 A4:Streetside action wall cabinet, (1) upper storage area w/sliding polycarbonate doors, (1)adjustable shelf, (1)locking drug compartment w/ hinged door and 7/8"lock. Note:See Item #2240 A.5 A5:Streetside CPR rear wall. Note:See Item #9010 1559 2014 Database 2/2/2016 VIN Number Parent Job 1559 ($132) ($29) Page 8 of 28 14-135 LEHDER RfTIBULHnCE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customs 1559 707-529-7522 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description A. 6 A6:Streetside bulkhead cabinet &wall with upper A/C removable panel,and opening for oxygen access with hinged plexiglassdoor.Cabinetsplit,uppersection w/hingedwood door w/ non lockinglatch and (1)adjustable shelf, lowersection w/ hinged wood door w/ lockinglatch,w/vent (Invertercomp.).Top ofcabinet to have Gibraltarcountertop. Note:Split Cabinet horizontallyin Center Upper section will bethe radio compartment with hingedwooddoorw/non-locking latch and vent Inside @top will require awood panel approx.5"widetomounta (7)position switchpanel.See Option #5210. Lowersection willbe a storage compartmentwithhingedwood doorw/ non-lockinglatch. NOTE:Cabinet needs to be as wide as possible. NOTE: No oxygen access hole needed. Refer to Prints A.7 A7:Bulkhead overhead electrical storage cabinet,(1) hinged wood door w/ locking latch. A. 8 A8: Partition door, sliding (clear) plexiglass window,hinge door on passenger side, door will swing into module. A. 9 A9:Curbside bulkhead cabinet ALSw/exterior access,split cabinet,upper section w/ (2) hinged 3/8"smoke polycarbonatedoorsw/plastic "D"ring latches, (1)adjustable shelfw/ aluminum lip.Lowersection w/ (2) hinged wood doors w/lockinglatches, (1)adjustable shelf w/aluminum lip. Note:See Item #2250 A. 10 A10:Curbside squad bench, exterior Stainless Steel riser, (2) hinged lidsw/ holdopen gas struts and Southco rubber"FlexDraw"hold down latches.Top drop trash and sharps container @ head end of squad bench.(Trash &sharps container included). Note:See Item #2290 ____^_ A. 11 A11:Cabinet over squad bench, dividedintotwo sections w/ hinged (flip up) 3/8" polycarbonate doors w/ plastic "D"ring latches Note:See Item #2260 A. 12 A12:Contor Consolo, (2)sido vonts, romovablofaco.Diroctly behind console is a soporoto romovablo mop boxw/(2) cup holders, polycarbonate dividoro,(1) 12 voltoutlot, (2)dual 12 volt USB port. Laminate Color: Dark Groy ff10592 Note:See Item #2270 A. 13 A13:Action wallpanel, exteriorlaminatecarbon fiber,cut outs for 02 outlets, Time Manager,110V, 12V, USB, and volume control. A. 14 AH:Gibraltar "Liquid Stop"mounted on floorinwalkthrough, botwoon cab &modular Note:Freightliner Crawl Through.Diamond Plate Aluminum Transition Plate. A.15 A15:Modular headliner to be 1/4" MDF,laminated with White Formica,Matte Finish A.16 A16: Misc.Wood Material- (3)Seat Cushions,(3) Back rests, (2) Head Rests,(3) CPR head bumpers, (2)CPR side bumpers, Curbside wall,head bumpers,fillers,wood sub-floor,A/C Styrene Board 2000 -INTERIOR CABINETS -OPTIONS A.2000 A. 2190 Supply restockingframe on upper overhead cabinet (pricedper cabinet) Note:Quantity:4 All upper level streetside cabinets. 1559 2014 Database 2/2/2016 Page 9 of 28 ($87) ($17) $1,124 14-136 LEADER nmBuuincE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 NewportBeach Fire Customei 1559 707-529-7522 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description A.2200 SPECIAL: CUSTOM A2 Streetside upper rearcabinet, Add (1)upper adjustable shelf. 1)ADDCUSTOMA2 MID LEVEL:Custom 6"deep X 24.5 tallmid level cabinet set backingto partial depth exteriorcompartment section. Glove box storage to accomodate 3 customer suppplied glove boxes.Hinged polycarbinetdoor.(Gloves included) 2) (1)midlevelstorageareaw/sliding polycarbonate doors,andtwo (2)adjustableshelves. REFER TO PRINTS A.2230 SPECIAL: CUSTOM A3:Streetside storage cabinets to left of CPR seat CUSTOM UPPER LEVELA3:Storage cabinet 13"tell interiorheight, w/ sliding polycarbonate doors, withone (1) adjustable shelf. CUSTOM MID LEVEL A3:Open storage countertop 13.5"deep. CUSTOM LOWER LEVEL A3:A12"deep cabinet below the countertop. Install two (2)4"tallaluminumdrawerswithaluminumface (laminated)and lockingChrome Steel "D" ring latches,and additional7/8 key locks. NOTE:Drawers to be recessed 6" in from isle. Refer to prints. A.2240 SPECIAL: CUSTOM A4 Streetside action wall cabinets, Two (2) upper storage areas, 13"Interior height cabinets w/ sliding polycarbonate doors, and one (1) adjustable shelf. One (1)Full heightX14" wide X12" deep Mid levelinset cabinetw/ (2)adjustable shelves,and (2) hinged 3/8" plexiglass doors withChrome "D"ringlatches. Locate:at the forward end of the attendant counter. Stainless Steel Action area surround, (side and back wall). Note:Refer to optons A.2190, &9310. A.2250 SPECIAL: CUSTOM A9 Curbside bulkhead cabinet ALS access,split cabinet,upper level storage cabinet Left section to accommodate a Knox 5502 Medi-vault Refer to option 7230 Upper rightstorage cabinet w/Top hinged polycarbonatedoor. Mid-section:w/ (2)hinged 3/8"smoke polycarbonatedoors Chrome Steel "D"ringlatches, Two (2) adjusteble shelves,Solid 3/4"wood, Formicacovered with 1/8"edge banding and a Gibraltar lipto the interior opening. A pairof LED Strip lighting on each side of the opening. Lower Level: Installa single 6"tallby 20"deep aluminum drawer with aluminum face (laminated) from the exterior accessible from the curbside exterior. Drawer to have a Chrome locking "D"ringlatch. Raise the slide out drawer and cabinet floor under itto provide a 22.5" tall opening to accommodate a drug box and monitor below iton the compartment floor. The lower section will extend above floor level.Close out to interior. A.2260 SPECIAL: CUSTOM A11 CABINET:Cabinet over squad bench,divided into two sections w/hinged (flipup) 3/8" polycarbonate doors w/ Chrome Steel "D"ringlatches, and gas strut hold opens. Both sections to have removable 3/4" tell front retaining lip,and 6 adjusteble plexiglas dividers. Configureto optimize usable height A.2270 SPECIAL: 1559 2014 Database 2/2/2016 Page 10 of 28 $515 $483 $598 $503 $358 $393 14-137 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customer' 1559LEADER---"'" HmeuuincE Steve De La Montanya 707-529-7522 10941 Weaver Avenue South El Monte,CA 91733 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description CONSOLE FOR FREIGHTLINER CHASSIS: Console to be fabricatedfrom.125"aluminumwitha texture paint(DarkGrey) finish. Itwill incorporate a 6" long level forward section The forward,curbside 6"section of the console will be reserved for the MDT install area. The forward streetside side area will be reserved for the Chassis heat AC controls and the added meters. There willbe a 6.25"" long angled panel section. This will be used for the Whelen Siren Control and the Whelen Traffic Advisor. Tothe rearofthis will be a largeflatpanelwiththe Mobile Radioinstellareaandthe Intercom pushto talk buttons. 12V USB outlets,Cup holders, &map storage willbe located behind the main console. Refer to Prints. Note:Refer to option9320 forMDTmount to be instelied. Reinforce passenger side to accept specified MDT mount III Final details to be determined after the chassis arrives at Leader. A.2280 SPECIAL: INSIDE ACCESS TO AN EXTERIOR COMPARTMENT: Locate:Curbside rear,Access intoupper forward portionofthe curbside rear compartment Configured Single Hinged Plex Door,Non locking chrome pull latch. A.2290 SPECIAL: CUSTOM CURBSIDE SQUAD BENCH: Two (2 pair)Six pointretractable seat belts, forattendants, and (2)seat belt straps for patient Custom head end configuration withtop droptrash, single hinged red plex doorwithdropthrough hole located near the wall.Horizontel drop sage sharps container and an open storage cabinet located inthe forward position. (Trash &sharps container included). Refer prints for configuration. A.2300 SPECIAL: CURBSIDE WALL IVSUPPLY CABINET. Locate at the head ofthe bench, Cabinet to butt up to the upper curbside cabinet The top portionwill the curbside 02 outlet and an open storage bin. The center portion willbe forIVsupply storage and is to have two (2) adjustable shelves w/aluminum frontlips and a hinged Plexiglas door. The bottom section will be open storage with four (4)adjustable dividers,for IV needle storage. 300 -INTERIOR TRIM AND COLOR -STANDARD B. 1 Floorcolor/material -(Coved),Anti-Microbial,UV Protected, Lonseal-Loncoin II Flecks, #150UVOnyx. B. 2 Gimp,Headbumpers,Fillers upholstery color/material -Black Doeskin #DOS4849w/1/4" closed cell foam. Note:See Item #3010 B. 3 Laminate color,exterior Matte,Light Gray- D355/interior compartments tomatch exterior. B. 4 Laminate color, Action wall panel laminated in Carbon Fiber finish. B. 5 Polycarbonate color.240, tinted 1559 2014 Database 2/2/2016 Page 11 of 28 $253 $114 $480 14-138 LEADER flmeuLflncE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customa 1559 707-529-7522 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description B. 6 (3)Seat Cushions,(3)Back Rests,(2)Head Rests,(2)CPRSide Bumpers,(3)CPRHead Bumpers- "Water Fall"style, 2"foam,velcrofasteners. Color/material Black Doeskin #DOS4849 Note:See Item #3010 B. 7 AttendantSoat High Back (Wiso),6 dogroo,modium donsityfoam,3 pointcoat bolt,sown w/Loador Logo, w/ swivel base. Color: BlackDooskin #DOSd810 (LoaderSupplied L#05 151) Logo:RodAIVhito Note:See Item #3010&#3130 B. 8 Counter Top Color,Midnight Melange •Gibraltar Material Note:ColonSteel Grey Tempest B. 9 Doorpanels are to be aluminum covered with D355 Light Gray laminate,w/6"Red #983-72 3M Conspicuity reflective safetystripe(see printfor location)w/stainless steel bottom of panels B.10 Polycarbonate sliding doors,retain handlesondoorsand provide holesforcableties. B. 11 The patientarea ofthe vehicleshallbe insulatedw/2"Owens CorningQuietR,glass fibers,fireresistant, fungi &bacteria resistance, forboththermal and acoustic insulation 3000 -INTERIOR TRIM AND COLOR -OPTIONS B.3000 B. 3130 Attendant seat 6 degree high back withbuiltinchild seat.ILOS,NOTE:This is not available in vacuum form,will be "Sewn" Note:Colon Light Grey B.3200 SPECIAL: INTERIOR CHROME LATCHES: Delete standard Black Plastic D ring pull latches Replace with ChromeSteel D ring latcheswhena pull latch is required. See Prints B.3210 SPECIAL: COLOR CHANGE: Delete Black, Replace with Sierra Light Grey TL-2000 B.3220 SPECIAL: OPTIONAL INSULATION: 1.(3)Patient Compartment Access Door interiors aretobe lined with damping pad (L#20-13029)in addition to the standard insulation. 2. PatientCompartment Ceiling to be lined with High Temp (L#20-13030)in addition tothe standard insulation. 400 -WARNING DEVICES -STANDARD C. 1 Warning Lights,frontofuppor modulo ILO lightbar,(7)total,Wholon 900 Supor LED,(5) Rodw/ Rod Ions, (2)Whitow/Cloar Ions.Contor lightto bo steady burning.Chromo flongos included. „R„,w,,,R.. ..R.. „R....w....R.. Note:See Item #4500 1559 2014 Database 2/2/2016 Page 12 of 28 ($439) $926 $491 ($741) 14-139 LEHDER HmeuLflncE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 Newport Beach Fire Customei 1559 707-529-7522 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan (949)644-3363 Itemnumber Description C.2 Warning lights,rear of vehicle,upper outboard corners,-(2)Whelen 900 Super LED Rod w/ Red lens.Chrome flanges included. Note:See Item #4510 C. 3 Warning lights,sido,(4)Total,(2)porsido,Wholon 000Supor LED Rodw/Rod Ions. Chromo flangos includod. Note:See Item #4520 C.4 Warning lights,grillo,(2)Wholon LIN3 Supor LED Rodw/RodIons&Chromo Housing. Mounted on upper horizontal grille bar. Note:See Item #4530 C. 5 Warning lights,roarof vohicio,window lovol,(2)Wholon 900Supor LED Ambor w/Ambor Ions.Chromo flangos includod. Note:See Item#4540 C.6 Intersection lights,frontfenders, (2)Whelen700Super LED Red w/Red lens. Chromo flanges included. Note:See Item #4550 C.7 Headlight flasher,Leader solid state,electronic,console switch. C. 8 Sirenspeaker, (2)Cast Products100wattsirenspeakers, recessed throughfront OEM bumpor.(Polished Aluminum Finish) Note:See Item#4700 C. 9 Scono lights,sido,(<1)Total,(2)porsido,Wholon 000 Halogen w/Clearlens.Chromo flanges included. Note:See Item#4570 C. 10 Scene lights,rear,(2)Whelen 700 Halogon w/Cloar-lensi-Chrome flanges included. Note:See Item#4570 C. 11 Running board lights,(2)Wholon //20C0CDCD LED,(1)perside mounted onsplash shiold,activate via cab doors;-constant hot: C. 12 Front,rearandside FMVSS LED marker lights w/Chrome housings. Front; (5)Amber lights Rear;(5) Red lights Side @ Rear (2)Red lights C.13 Bockup,turnand stop/tail lights,Wholon 600 LED w/Chromo flangosshallboas follows: (2) Turn Signal Lights, Wholon 600 LED Amber w/Amber lens w/arrow—outboard on diamond plate. (2) Stop/Tail Lights, Wholon 600 LEDRod w/ Rod lens • inboard on diamond plato. (2) Bock UpLights,Wholon600 LED Whitew/Cloar Ions—abovo diamond plato on body. Note:See Item#4590,4600.4690.4580.4650 C.14 Brako light,roaruppor contor,Kinoquip LED Redw/RodIons. Note:See Item #4610 C.15 Back-up alarm,rear mounted,97 decibel with auto reset,console defeat switch C.16 Warning light flasher (2)Vanner#3250 GCPE C.17 Siren electronic, located inover head console, Whelen dual tone #295HFSA7w/ remote amp CA spec,(hi-lo deleted)100 watt output w/removable mic,hands free horn ring control. Note:Siren to be re-located to center console. 4000 -WARNING DEVICES -OPTIONS 1559 2014 Database 2/2/2016 VIN Number Parent Job 1559 Page 13 of 28 ($198) ($397) ($95) ($198) ($108) ($408) ($147) ($73) "($97) ($406) ($22) 14-140 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Custome, 1559LEADER~ HmBULHnCE Steve De La Montanya 707-529-7522 10941 Weaver Avenue South El Monte,CA 91733 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description C.4000 C. 4410 Add opticom to light bar C. 1 Opticom (LED)GTT 794H Emitter (Self contained)NOTE:(Includes Activating via Primary Switch,and wired thru Park/Neutral cut-off. Note:There shall bea separate cutout switch (option #5220)installed onthe front switch panel. Locate Opticom below M7 light See Print C.4500 SPECIAL: FRONT LIGHT BAR ALTERNATIVE:WHELEN LED"M"SERIES LIGHTS W/CHROME FLANGE (4) M9R Red (flashing) (2) M9CWhite (flashing) (1) M7RS Red (steady) (6) M9FCChrome Flange (1) M7FCChrome Flange See Print for location. C.4510 SPECIAL: Warning lights,rear of vehicle,upper outboard comers,(2)Whelen M9R Series LED RED Warning lights w/Chrome Flange C.4520 SPECIAL: Warning lights(4)total.(2) perside, Whelen M9RSeries LEDRed Warninglightsw/ Chrome Flange. C.4530 SPECIAL: Warning lights.RearofVehicle,windowlevel.(2)Whelen M9Aseries LED Amberw/Chrome Flange. C.4540 SPECIAL: Warning light front grille,Four (4)Whelen M7R Series LED Red Warning lights w/Chrome Flange. Locate:two (2)onthe upper portion ofthe grille and two (2)onthe lower portion ofthe grille. C.4550 SPECIAL: Intersection lights,front fenders,(2)Whelen M7D Series LED Split Red/Clear Warning w/Chrome Flange. C.4560 SPECIAL: Intersection lights,rear fenders,(2)Whelen M6D Series LED Split Red/Clear Warning w/Chrome Flange. C.4570 SPECIAL: SideScene lights,(4)total,(2)persideWhelen M9LZC Series LED Clear Scene lights w/Chrome Flange. Rear Scene lights,(2)total,Whelen M6ZC Series LED Clear Scene lights w/Chrome Flange. C.4580 SPECIAL: Warning lights Flashing (2),Rearof Vehicle,one aboveeach BrakeTaillight Whelen M6R Series LED Red Warning lights. Install in top position ofWhelen #M6FCV4 Chrome Flange,refer to option 4650. C.4590 SPECIAL: Rear Brake/Tail lights:(2)Whelen M6BTT Series LED Red Brake/Tail lights. Referto option 4650 C.4600 SPECIAL: RearBack Up Lights:(2)Whelen M6BUW Series LED Clear Scene BackUp lights. Referto option 4650. 1559 2014 Database 2/2/2016 Page 14 of 28 $2,190 $1,406 $416 $832 $416 $602 $312 $318 $1,784 $244 $183 $244 14-141 LEADER RfllBULHnCE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 Newport Beach Fire Customs 1559 707-529-7522 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description C.4610 SPECIAL: Brake Light rear upper center.(1)Whelen M7RS Series LED Red light w/Chrome Flange C.4620 SPECIAL: TRAFFIC ADVISOR:(1)OneWhelen Low Profile #TAM85 with (8)TIR6Super LED Traffic Advisor(w/ 30 foot cable)mounted above the rear doors with the control head in driver's console. NOTE:The Traffic Advisor shall be wired directly tothe batteries C.4630 SPECIAL: ENTRY DOORMARKER LIGHTS:Install L#02-893Whelen flashing doormarkerlights. Quantity:Six (6). Two (2) per door. Configure to come on when the door is opened. Locate:Outer Comers Refer to prints. C.4640 SPECIAL: COMPARTMENT DOOR MARKER LIGHTS:Compartment DoorMarker lighte:L#02-893 Whelen LED Flashinglightsto allexterior compartment doorinner panels. (1)on each short door panel @ top of M2 compartment and (2) per door@ top &bottom on alltalldoor panels - M1, M3, M5,M7. Locate:Outer Comers Total of 12 lights. Note:See option 68.6 C.4650 SPECIAL: TAIL LIGHTFLANGE:Whelen #M6FCV4 Chrome Flange. Note:This flangewill house Brake/Turn/back-up/1 emergency flashinglightoption#4580. Instell on Driver andPassengersides rear abovethe Diamond Plate Riser. C.4660 SPECIAL: SIREN SPEAKERS ILOS,FEDERAL One (1) Federal 200 watt,#BT200 connect to the Specified E2QB One (1) Federal 100 watt,#ES100 Connect to the Whelen Siren Recessed thru frontOEM bumper (outboardsections). Freightliner Chassis. C.4670 SPECIAL: CUSTOM SIREN CONFIGURATION:Siren electronic,Federal EQ2B Locate In front center console. Connect to Federal Siren Speaker in passenger side front bumper as listed in option #4660. C.4680 SPECIAL: BROW LIGHT:Add"Brow Light"Whelen Pioneer#PFP2 (Dual Flood PioneerPlus) Leader builtMountModulew/ Radius Mount(3"Radius) Note:The Mounting hardware is to be powder coated whit Locate:Mounton frontradiusof Module(centered) See Option #5270 C.4690 SPECIAL: Rear Turn Signals: (2)Whelen M6T Series LED Amber Turn w/ Arrow. Referto option #4650 500 -ELECTRICAL CONTROL CENTER -STANDARD D. 1 Bulkhead electrical storagecabinetcomponents, fuse bar,fuse barbracket,terminal blocks 1559 2014 Database 2/2/2016 Page 15 of 28 $158 $1,269 $180 $309 $327 $1,127 $1,217 $158 14-142 LERDER RmBULHnCE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 707-529-7522 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 ChipDuncan (949)644-3363 Customei 1559 Itemnumber Description D. 2 Ovorhoad consolo,fiborgloss (Groy)ovorhood consolo to houso switchos,siron,indicator lights. Note:DELETE,Freightliner type configuration. EloctricalSwitch Panol, front ovorhood consolo,santox (Carbon Fibor Finish), back litw/ blank logonds. Note:See Item #5240 D. 5 Voltage meteranalog,locatedinoverhead console,TST0-18 volts. Note:Meters to be re-located to center console. D.6 Amperage meter analog,located in overhead console,TSTwith remote induction sensor• no shunt. Note:Meters to be re-located to center console. D. 7 D. 8 D. 9 Indicator lamp Green,MASTERON, C.H. LEDpilotlight. Indicator lamp Red, EMERG START,C.H. LEDpilotlight. Indicator lampRed,DOOR OPEN,C.H.LED pilot light,includes all(9)doorswitchesfor exterior compartments and patient access doors. D. 10 Indicator lamp Red,PARKING BRAKE,C.H. LEDpilotlight,w/ buzzer. D. 11 Switch, PRI.SEC.CH LED,litRed/Amber,center off,primary controls all emergency lights,secondary controls rear Amberwarninglightsonly. Note:Secondary to control Front Steady Reds and all Rear Facing lights Only. D. 12 Switch,HEADLIGHT FLASHER, C.H. LED, litWhite. VIN Number Parent Job 1559 ($300) ($53) D.13 Switch,BACK-UP ALARM,C.H., non-lit momentary. D. 14 Switch,LEFT FLOOD,C.H.LED, lit White. D.15 Switch,REAR FLOOD,C.H. LED, lit White. D. 16 Switch,RIGHT FLOOD,C.H. LED, lit White. D.17 Switch, PATIENT DOME, 3-way, C.H. LED,litAmber. D.18 Switch, PATIENT HEAT/AC,3-way, C.H. LED, litBlue. D.19 Switch,MODULE DISCONNECT,C.H. LED, lit Green. D.20 Switch, EMERGENCY START,momentary toggle w/switch guard,non-lit Note:Relocate this switch to the center console. D. 21 Map lights,(2)dual RedAWiite LED map lightslocatedincab overhead console, (1)above driver, (1)above passenger. D.22 100,000 CP Spot light,black rubbor, halogon Cloar, hard wirod.(clipsupplied looso) D.23 Two-way radiopower,Positive-Negative-Ignition,with terminal strip,located insidecenter console. 1559 2014 Database 2/2/2016 ($64) Page 16 of 28 14-143 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customei 1559LEHDER™.« HmBULflnCE Steve De La Montanya 707-529-7522 10941 Weaver Avenue South El Monte,CA 91733 (949)644-3363 VIN Number ParentJob 1559 Itemnumber Description 5000 -ELECTRICAL CONTROL CENTER -OPTIONS D.5000 D. 5110 12Volt wiring,pair.Positive -Negaitve,20amp protection,terminate behind driver seatw/ 3 feet of coil. Note: Note: Quantity: Four(3) These willbe used for the following: Use 12 gage wire w/10 amp circuit breakers, NOTE:Power for these (3)will come from AUXILARY POWER BATTERY Locate: (1)set for the drivers side Portable radiocharger. Locate:(1) one set behind the passenger seat, forthe passenger side Portableradiocharger. Locate: (1)one set in the streetside rear exterior compartment,for"Box"light Configure:Wire continuously Hot to designated AUXILARY POWER BATTERY in the streetside intermediate compartment NOTE:Label allwiring. D.5200 SPECIAL: AUDIBLE BUZZER: Module Side and Rear Entry DoorOpenAudible BUZZER wired through F7N switch. D.5210 SPECIAL: (1)AUXILARY RADIOPOWER TERMINALSTRIP (3)Gang: (6) gage Positive- (6) gage Negative - Ignition.Located inside Radio Compartment Add a (7) Position back litswitch plate w/legends (listed below) inside upper section of Radio Compartment (4)Pos-Neg 12 gage Circuits from terminal strip. (3) out of the (4) circuits need to be wired through a Momentery (Normally On)Rocker Switch protected with 20 amp circuit breakers terminating inthe following Switches: Circuit1:(W/Rocker Switch)"DRUG VAULT" -Terminate ALS Cabinet Circuit2:(W/Rocker Switch)"KEY VAULT" -Center Console Circuit3:(W/Rocker Switch)"MODEM"- Radio Compartment Circuit4:(W/Out Rocker Switch)"MDC"-Center Console Configure: Wire 6 gage continuously Hot to designated AUXILARY POWER BATTERY in the curbside intermediate compartment Label allwiring. D.5220 SPECIAL: OPTICOM DEFEAT W/AUTO RE-SET: Add a momentary switch in the "C" position in front center console. NOTE:Once the circuithas been defeated it needs to automaticallyre-set when the Primary-Secondary switch Is activated. D.5230 SPECIAL: CUSTOM SWITCHING REQUIRMENT: Patient Compartment Exhaust Circuit- 3-way, With lit Amber Rocker Switches: Customer requesting to have a switch for patient compartment exhaust located in cab in addition to patientcompartmentswitch,locateswitchinthe "J"position on front panel. D.5240 SPECIAL: 1559 2014 Database 2/2/2016 Page 17 of 28 $156 $47 $293 $87 $47 $67 14-144 LEADER flmBUUincE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 Newport Beach Fire Customer 1559 707-529-7522 3300 Newport Beach BLVD Newport Beach, CA 92658 Chip Duncan (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description Note: Custom Switch Panel: Freightliner Dimensions,(12)Switch Positions,(5)Indicator light positions. Back Lit,Carbon Fiber Finish. Located in overhead OEM headlines D.5250 SPECIAL: INSTALL (2)CUSTOMER SUPPLIED PORTABLE RADIO CHARGERS: Location:Rear of center console map box,Constant Hot Refer to Prints D.5260 SPECIAL: CAT 5 WIRE ONLY: Supply &Install Cat5 wireinthree locations w/3 feet of coil: - From Radio Compartment to Center console forMBC - FromRadio Compartment to Center console forKeyVault - FromRadio Compartment to ALS Cabinet forDrugVault NOTE:Customer to install connectors and do the final connections.Leader to supply wire only. D.5270 SPECIAL: BROW LIGHT SWITCH: Add a on/off Lit White switch in the "D"position In front overhead console.Labled "BROW LIGHT 600 -ELECTRICAL PATIENT COMPARTMENT -STANDARD E. 1 Dome lamps, ceiling,(8)flush mount, Whelen LED High-Low Dome Lights.Doorjamb switch activated (lowintensity) and switch panel activated (high-low) E. 2 Electrical outlet 12 volt, Blue Sea #1011,Three (3)cigarette lighter style. Location: (1)Rear action wall (1) ALS cabinet (1)Center console E. 3 Electrical outlet 12 volt, Blue Sea #1016,Three (3) Dual USB Port. Location: (2)Center console (1) Action wall area $76 $118 $82 E. 4 Electrical outlet (2) 120V, ALScabinet, action wall,with pilotlights, mounted on grey plastic housings,wired to shore power. Note:See Item #6060 E. 5 Switchplate rear, (10) position Santex (CarbonFiberFinish)back litw/blanklegends. Note:(Sinale Row Switch Plate) E. 6 Switch,DOME,3-way,C.H. LED, litAmber. E. 7 Switch,DOME HI-LO, C.H. (non lit) E. 8 Switch,ELECT SUCTION,C.H.LED,lit Amber. E. 9 Switch,EXHAUST,C.H.LED, lit Ambor. Note:See Item #5230 ($4) E.10 Switch,PATIENT HEAT A/C,3-way,C.H. LED, litBlue. 1559 2014 Database 2/2/2016 Page 18 of 28 14-145 LEHDER HfTlBULflnCE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 Newport Beach Fire Custome, 1559 707-529-7522 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Itemnumber Description E. 11 Switch,A/C,FAN HI-LO,C.H,(non-lit) E. 12 Switch,A/C,HEAT-COOL,C.H.(non-lit) E. 13 Switch,COMPARTMENT LIGHTS,C.H.LED,litWhite E.14 Switch defeat,PATIENTDOME,side and rear door, C.H. (not lit) E.15 Switch defeat,RIGHT FLOOD, C.H. (non-lit) E.16 Switch defeat,REAR FLOOD, C.H. (non lit) (949)644-3363 E.17 Switch plate, (Defeat Switches)(2) position Santex (Carbon Fiber Finish) E.18 Radio rear volume control for AM/FM,action wall area See print for location. E. 19 AM-FM-Speakers (2)above rearaccess-doorsinpatient compartment Note:Delete E. 20 Shore-power. 120V.15 amp. behind driverdoor, Hubbell cast cover, wired to 110Voutlots in patient compartment. Note:See Item #6340 E.21 Restocking light time,squadbench wall @headend,five minute,controls (4)dome lights over cot (high intensity) E.22 Clock,Emergency Time Manager,mounted in action wall panel,chimes. E.23 Interior cabinet lighting,LED strip lighting insidecompartments including belowactionwall panel,activated w/ lit switch in action wall. E.24 Step Well Light LED,located in side door step well,door switch activated, E. 25 Inverter Pre-Wire,Includes12voltPos-Neg with Andersonquickdisconnectconnector, terminating inside inverter compartment. (Does not include remote panel or rocker switch) 6000 -ELECTRICAL PATIENT COMPARTMENT -OPTIONS E.6000 E. 6060 Electrical outlets 120V,additional location,(location on print),pilot light,stainlesssteel, tie in to 120 circuit, (in addition to standard). Note: Quantity (2) (1) Additional Located in ALS Cabinet (1) Additional Located in Action Wall Area. Referto Prints E.6320 SPECIAL: 1559 2014 Database 2/2/2016 VIN Number Parent Job 1559 ($43) $208 $1,748 Page 19 of 28 14-146 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customs 1559LEHDER™o,6 RfTIBULfinCE Steve De La Montanya 707-529-7522 10941 Weaver Avenue South El Monte,CA91733 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description BATTERY CHARGER/INVERTER:Newmar/Kussmaul #430-120000 50 amp Charger,12000 Watt inverter. Charge monitor 020-4290-0, Locate:Charger/inverter inside streetside intermediate compartment,lower rightside. Locate:Charge Monitor above exterior shore inlet Inverter Panel 0202-4289-0 Locate: Inverter panel to be located in the attendant area. E.6330 SPECIAL: REVERSE CAMERA WITH ABOVE WINDSHIELD MOUNTED 7" LCD MONITOR: Instell a Voyager AOS713CMB Kit Backup camera over the rear doors, Installthe 7" LCD screen in the cab upper storage pocket above the drivers seat This willrequire a custom fabricated and painted steel mounting plate. Wireto activatewhen the vehicleis placedintoreverse. E.6340 SPECIAL: SHORE POWER:Kussmaul Super Auto Eject 20 Amp. Red Cover. 700 -ELECTRICAL AND MECHANICAL -STANDARD F. 1 Air conditioning/heater,driver compartment switching control dash, Ford OEM,w/prep for rear air. Note:Freightliner OEM.Includesdualcompressors, one forcab and one forconversion. F. 2 Air conditioning/heater,patient compartment,ductedcentralair,with intakevent,and (6) A/C round louvers. Note:Freighliner Kit includesunderbodycondensor F. 3 Air conditioning hose,shielded low loss,wedged on fittings, R134 (included w/ F2) F. 4 Heater hose,Nomex, Ford QVM (included w/ F2) F. 5 Tri-Battery system- (2)primary,and(1)emergencystart,redundantbatterysystem wiring and electrical components.Overhead console mounted LEDRed indicator lamp and activation switch. Includes (1)battery under hood in OEM location, and (2) 65 series batteries located in battery box. Note:Tristert system,(2) PrimaryBatteries,and (1)Emergency Boost Battery.Batteries located inside M2 exterior compartment Refer to option #7200,Additional battery isolated for radio and electronics located inside M2 exterior compartment Total of(4)batteries. F. 6 Shut Down Timer,with 5 min.delayactivatedvia ignition switch. Note:Set time to 15 minutes F. 7 Wiring loom,Leaderfabricated,hitemp SXL,colorcoded, numbercoded and function labeled,with split loom wire protection F. 8 Antenna wiring (2)RG58A/U coax,roof location # 1&2 with StainlessSteel (Interior) access plates,terminate in cab,inside center console. Note: Leader supplied,Refer to Option #7040 #1 Antenna to terminate inside Radio Compartment #2 Antenna to terminate inside RadioCompartment (Spare) F. 9 Power Exhaust vent,left rear,Cast Products exterior cover,interior louver round 1559 2014 Database 2/2/2016 Page 20 of 28 $852 $394 $845 14-147 2/2/2016 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customei 1559LEADER HmBULHncE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 707-529-7522 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description F.10 Remote door lock release,front grille. NOTE: Installation of Remote Door LockSwitch feature may increase the likelihoodof unauthorized entry into vehicle. Withthis feature,purchaser further agrees to hold Leader Ind. or chassis manufacturer harmless for any loss of vehicle or contents caused by unlawful access.(Customer has the option to Delete this feature) Note:Relocateto upper portion ofthe rearlicense platehousing. F. 11 Reverse activated (rear)loading lights F.12 Auto Throttlo (Gas Engino),In Power ffDBT LD (Ford QVM Approvod) Note:Freightliner Idle control. 7000 -ELECTRICAL AND MECHANICAL -OPTIONS F.7000 F. 7040 MBO Antenna Base (each) Note:Quantity(2) F.7200 SPECIAL: ADD OPTIONAL BATTERY:Add a Deka Group 31-1000 CCA battery. This battery is to be an isolated power supply for the communication equipment Locate in the battery tray in the bottom of the intermediate compartment This battery is to be tied to the chassis charge system and to the second output on the specified battery charger. F.7210 SPECIAL: 1559 2014 Database 2/2/2016 Page 21 of 28 ($49) $90 $472 $4,170 14-148 LEADER HfTIBULflnCE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Custome. 1559 707-529-7522 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description INTERCOM SYSTEM:A David Clark3800series communication system. Ill NOTE:THIS SYSTEM NEEDS TO BE CONFIRMED FOR CORRECTNESS WITH SIGN OFF PRIOR TO ORDERING PARTS.III One (1), MasterStation box #U3800 to be located centered overhead, aft on the bulkhead,between the driver and the passenger. Box shall accept two (2)head set plugs with master and individual volumes. Install One (1)hangeron each side forone (1)ofthe two (2)headsets adjacentto the box. Three (3) Headsets: (2)#H3442and(1)#H3441 Refer to Prints for location: LEADER SUPPLIED PARTS FOR CURRENT CONFIGURATION: 1)#U3800- MasterStationbox (locate In cab on upper partition) RadioCordJunction Module(locateinside radio compartment) Radio Interface Module/ PTT(locateinsidecenterconsole) Radio Interface/Headset Stetion (locate @ actionwallarea) Headset/Mic (Single Ear) Headset/Mic Jumper Cord 25Ft Radio Interface Cord 21 Ft 1)#C38-12 -Jumper Cord 12Ft 1)#C38-20 - Power Cord 20Ft 2)#C3821-05 - Radio Interface Cora*20Ft ;2)#18352G-07 - MS Conector 5 pin For Remote PTT Guard PTT Switch PTT Dpst Electrical Cord For Remote PTT40Ft Neoprene Washer (Packet of 10) Footswitch(locate in actionwallarea loose) 1)#U3805- 1)#U3810- 1)#U3815- 1)#H3441- 2)#H3442- 1)#C38-25 1)#C38-21 2)#26553P-01 2)#09851P-28- 1)#09815P-20- 1)#18900G-01 1)#40071G-04 The customer will be responsible to interface cables to any Two-Way Radios. F.7220 SPECIAL: INSTALL CUSTOMER SUPPLIED RADIO HEAD &CABLES: -Install radio head w/custom bezel in the center front console in cab. - Installradiocable fromcenter console incab to the radio compartment - Instellradio speaker incab (upper headlinercentered) NOTE:Customerto install radio bases, anddo final connections. F.7230 SPECIAL: KNOX MED VAULT:Knox MedVauft®Narcotics Locker. 5502 (w/out software)Flush mount w/ Flange, WiFi Enabled Locate:See option 2250,Front,curbside bulkhead cabinet F.7250 SPECIAL: BOXLITEFLASH LIGHTS:Provideand installPELICAN9410LBox Lights. Quantity:Two (2) Locate:Streetside rear compartment Note:Includes 12 volt pre-wire. Configure:Power hottoisolated battery. 1559 2014 Database 2/2/2016 Page 22 of 28 $240 $1,788 $778 14-149 Customer • Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan (949) 644-3363 1559LEADER HfTIBULflnCE Steve De La Montanya 707-529-7522 10941 Weaver Avenue South El Monte,CA 91733 VIN Number ParentJob 1559 Itemnumber Description F.7260 SPECIAL:$76 INSTALL A CUSTOMER SUPPLIED KNOX KEY SECURE:Install inthe forward right comerofthe front console below the MDT screen. Requires a constant hot power supply. F.7270 SPECIAL:$76 INSTALL CUSTOMER SUPPLIED GPS ANTENNA LEAD: Quantity:One (1) Originate:#1 Module roof,Streetside forward comer. Terminate:Radio Compartment 800 -OXYGEN SYSTEM -STANDARD G. 1 Aspirator,action wall area,SSCOR 22000,flush mount panel and gauge. G. 2 Vacuum pump,12V,w/vent tubeto exterior.Locate inside A6 cabinet. G.3 Oxygen system,Amico Ohio style quick release,(3)outlets,(2)in actionwall panel,(1)on ($43) wall above squadbench @ headend Note:See Item #8020 &#8400 G.4 ZICO Main 02 Bracket -Locate in M1 exterior compartment.Capable ofholding either "M" or "H"tank G. 5 Oxygen wrench,fastencableto wall by oxygen bottle. 8000 -OXYGEN SYSTEM -OPTIONS G.8000 G.8020 Flowmeter Integrated,Amvex 0-15 LPM (Tube Style)Replace (1)Standard Oxygen $210 Faceplate G.8101 Electric switched Oxygen with digital read out,replaces manual system,includes manual $837 by-pass. G.8121 Oxygen small bottle holder quick release,ZICO #QR-D-2,single "D"bottle only (strapless) G.2 ZICO #QR-D-2,single "D"bottle only (strapless)Quantity (2)$519 Note:Install inthe curbside module entry step well. G.8400 SPECIAL: RELOCATEATTENDANTAREA02 OUTLET:(1)ofthe two(2)02 outlets: Relocate one ofthe attendant area 02 outletsto the ceilingabove the head ofthe cot one to remain in action wall. Refer to prints. 900 -HARDWARE -STANDARD H.1 Soot bolts (A)Total,retracting lap bolts,(2)for squad bonch attendants,(1)for pationt on ($107) squad bonch,(1) for attendant soat on CPR soot. 1559 2014Database 2/2/2016 page 23of28 14-150 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customa 1559LEHDER™<>l6 HiTIBULflnCE Steve De La Montanya 707-529-7522 10941 Weaver Avenue South El Monte,CA 91733 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description Note:See Item #9010 H.2 |.v.holders,(2)positions,#1 &#3,Cast Products #A20-14 flush mount,polished aluminum. H.3 (3)Anti-Microbial 1-1/2 inch diameter stainless steel satin finish,angled door handles mounted on module access doors. H. 4 Ceiling grab rail Anti-Microbial,center mounted,stainless stool,satin finish 1-1/2" diomotor,72"longth. Note:See Item #9340 H.5 Door sills,(rear),bright stainlesssteel,w/ramp edge,(side)bright stainlesssteel sill 1 1/2" x 2 1/2" H. 6 Net,Frontend ofsquad bench,4 ancra fasteners, (1)rachet, Black1 1/2"webbing 9000 -HARDWARE -OPTIONS H.9000 H.9010 Six Point Restraints,(2)for squad bench attendants.(Requires back rest modifications) Note:Six PointRestraints,(1)for CPRseat attendant (Requiresbackrest modifications). Back Rest will no longer be a drop down. H.9300 SPECIAL: FIRE EXTINGUISHER:Amerx brand commercial gradewith vehiclemount,5 LB (shipped loose). Quantity:two (2) H.9310 SPECIAL: STAINLESS STEEL SHARPS POCKET: Attendant area back wall, (1), Leaderstyle, for Sage #R1002, bright stainless steel. (Sharps Container Included) H.9320 SPECIAL: MDT MOUNT:San Francisco FireStyle. (1) Mount #DL-TX204-MTU-O / Lund Tilt-Swivel Clamshell mount Locate:On passenger side forwrd section ofthe centerconsole incab.(reinforce mounting location on center console) H.9330 SPECIAL: 1559 2014 Database 2/2/2016 Page 24 of 28 ($77) $891 $226 $132 $381 $326 14-151 LEHDER HfTIBULHnCE 2/2/2016 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Custome • 1559 Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 707-529-7522 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description CUSTOM UNIT NUMBER PLATES:Provide 5 unit number plates (.125"Aluminum) Three (3) platesareto be approximately20"longX6"tall. Two(2)plates for the rearareto be halfapproximately 12"long X6"tall. Brackets andPlatestobe painted Redtomatchthe bodypaint Color Code:Sikkens RED FLNA 30006 Leader tomountunit number plates using 10-24 stainless steelscrewsand blind panel fasteners as follows: Note:1/8"Non Corrosive spacers will be provided between the mount plates and the body. -(1)20"x 6"plate located centered inside the opening ofthe front bumper. -(1)20"x 6"plate located on curbside centered between thebeltline stripe and "FIRE",centered with the lettering above. -(1)20"x 6"plate located onthe street side centered between the compartment opening and "FIRE" centered with the lettering above. -(2)12"x 6"plates located oncenteredthe right andleftsides ofthe module rear,centered with "NEWPORT BEACH" H.9340 SPECIAL: CEILING GRAB BAR 96" Install 96"grabbar,center over Right edge of cot Refer to Prints H.9350 SPECIAL: ADDITIONAL CEILING GRAB BARS (2) Install (2)24"grab bars, (1) on each side of the CPR seat next to streetside wall. Refer to Prints H.9360 SPECIAL: SCBA BRACKETS:Supplyand(Ship Loose)for customer install. BASIC SWING DOWN MOUNT:SKU QSD LOAD AND LOCK SCBA BRACKET:SKU:KD-ULLH Quantity.Two (2) 1000 -PATIENT HANDLING EQUIPMENT -STANDARD I.1 Cot fastener,Stryker #6370 floor mount,single position,front antlers removable.(Center Mount Position) Note:Set for Stryker Power Pro #6506 10000 -PATIENT HANDLING EQUIPMENT -OPTIONS I.10000 I.10200 (2015)Cot Safety Hook (Stryker)at Rear Sill w /Reflective tape Note:Set for Stryker Power Pro #6506 1100 -PAINT,BODY AND GRAPHICS -STANDARD J. J.1 An acrylicurethane paintprocess is requiredon the modulebody. J.2 Emblems,Leaderfrontfenders, rear doors, nosmokinglabels,ETC. 1559 2014 Database 2/2/2016 Page 25 of 28 $108 $132 $700 $71 14-152 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Custome. 1559LEADER HmBuifincE Steve De La Montanya 707-529-7522 10941 Weaver Avenue South El Monte.CA 91733 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description 11000 -PAINT,BODY AND GRAPHICS -OPTIONS J.11000 J.11200 SPECIAL: CUSTOM RED PAINT SCHEME: Cab to be repainted RED LOWER HALFAVHITE UPPER HALFfrom2" below cab doorwindows and extendontothe first sidebody line along the upper edgeofthe hood and turn into thetopcomersofthe chrome grill trim.The top ofthe hood is to be White. Refer to provided prints. Module is to be painted RED Color Code:Sikkens RED FLNA 30006 Color Code:OEM WHITE JHEV) J.11210 SPECIAL: BELTLINE STRIPE:Single6"beltline,Mid Body,upward jogonthe forward portion ofthe module. Refer to prints. SCOTCHLITE,White reflective. The stripe shall include 5/16 inch Black reflective pinstripe on edges. J.11220 SPECIAL: PAINT BREAK STRIPE:Option 195.2 Goldleaf paintbreakstripewithblack pinstripe top and bottom. White pinstripe below the lower black pinstripe on chassis cab. J.11230 SPECIAL: 1559 2014 Database 2/2/2016 Page 26 of 28 $4,400 $1,100 $800 $2,500 14-153 Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Customa 1559LEADER™»» HmeuuincE Steve De La Montanya 707-529-7522 10941 Weaver Avenue South El Monte,CA 91733 (949)644-3363 VIN Number Parent Job 1559 Itemnumber Description Note:GOLD LEAF LETTERING "SIGN GOLD": Laminated Gold Leaf, 1" Engineturn, 1/8"White borders, Black shadow left (Straight)approximately 6"Scale to fit (Straight)approximately 6"Scale to fit3 units (Straight)4 inch inwhite beltline Module Sides: •NEWPORT BEACH" "FIRE" Other lettering:"PARAMEDICS" Red Reflective Scotchlite Module Front •NEWPORT BEACH" Front of Chassis Hood: "FIRE RESCUE" chrome trim. Module Rear "NEWPORT BEACH" "FIRE" Other lettering:"PARAMEDICS" White Reflective Scotchlite (Straight)5.5"centeronthe front ofthe module below the ligt bar. (Straight)3.5"centeron the front edge ofthe hoodabove the (Straight)4" below windows (Straight)4 inch bottom of reardoors Black Shadow Left ADDITIONAL LETTERING:White Reflective Scotchlite (Straight)5.5 inch,Four (4)sets ofeach Unit Numbers,1 unit Unit #1 "NPB ###" Three (3)sets on single plates forinstall on the frontof the chassis and on the module sides. One (1)set of each on a splitpairofshorterplatesto be installed on the rearofthe module. White Reflective Scotchlite Referto prints J.11240 SPECIAL: REAR CHEVRON REFLECTIVE STRIPE:There shall bea rear Chevron reflective stripe onthe flat rear surfaces. The stripes shall be NFPA 1091 compliance. The Chevron stripes shall be6.00wideandbeinanupside down V pattern. Ill AddtranslucentRed Electro Cut#1172 backgroundto"NEWPORT BEACH FIRE"and "PARAMEDIC" The colorsshallbe Red andYellowper NFPA 1901 requirements. Colon 3M Conspicuity FluorescentYellow Green #983-23 Colon 3M Electro Cut Red #1172 Note:Black .250"Pin stripe border will be provided between each color stripe. J.11250 SPECIAL: MODULE ENTRY DOOR REFLECTIVE STRIPES:Instell 2"wideRedand White 3M Tape #983-326,High Index. Locate:Stripes along lower edge of inside door panels. J.11260 SPECIAL: Instell customer supplied cab door seals.Locate:Centered from front &rear door edge.Thetopistobe even with the body line.Leader to supply &install rock guard material over both cab door seals. 1559 2014 Database 2/2/2016 Page 27 of 28 $1,200 $100 $38 14-154 LEHDER HfTIBULflnCE Steve De La Montanya 10941 Weaver Avenue South El Monte,CA 91733 2/2/2016 707-529-7522 Itemnumber Description Newport Beach Fire 3300 Newport Beach BLVD Newport Beach,CA 92658 Chip Duncan Bysigningthe following documentyou are entering intoa sales agreement withLeader Industriesto purchase the above vehide/s. Customei (949)644-3363 1559 VIN Number Parent Job 1559 Contract Total:$250,862.00 Customer Representative Date:Sales Representative Date: 1559 2014 Database 2/2/2016 Page 28 of 28 14-155 Prepared for:Prepared by: Jason Cavallo TRUCK CTY OF WISCONSIN, Horton Emergency Vehicles INC. 3800 McDowell Rd 2401 PROGRESS WAY Grove City, OH 43123 KAUKAUNA,Wl 541309559 Phone:614-539-8181 Phone:920-766-5222 A proposal for Horton Emergency Vehicles Prepared by TRUCK CTY OF WISCONSIN,INC. Rick Kinney 2017 NEWPORT BEACH FIRE 1-11-16 Jan 11,2016 Freightliner M2 106 Components shown may not reflect all spec'd options and are not to scale Application Version 8.9.003 01/11/2016 3:24 PM Data Version PRL-10M.011 2017 Newport Beach Fire Page 1of15 14-156 Prepared for:Prepared by: Jason Cavallo TRUCK CTY OF WISCONSIN, Horton EmergencyVehicles INC 3800 McDowell Rd 2401 PROGRESS WAY Grove City,OH 43123 KAUKAUNA,Wl 541309559 Phone:614-539-8181 phone:920-766-5222 SPECIFICATION PROPOSAL Weight Weight Data Code Description Front Rear Price Level PRL-10M M2PRL-10M(EFF:02/11/15) Data Version DRL-011 SPECPR021 DATA RELEASE VER 011 Interior Convenience/Driver Retention Package 055-002 INTERIOR CONVENIENCE PACKAGE Vehicle Configuration 001-172 M2 106 CONVENTIONAL CHASSIS 5,759 3,503 004-217 2017 MODEL YEAR SPECIFIED 002-004 SET BACK AXLE -TRUCK 019-002 STRAIGHT TRUCK PROVISION 003-001 LH PRIMARY STEERING LOCATION General Service AA1-002 TRUCK CONFIGURATION AA6-001 DOMICILED,USA50 STATES (INCLUDING CALIFORNIA AND CARB OPT-IN STATES) A85-006 RESCUE AND EMERGENCY SERVICE A84-1EV EMERGENCY VEHICLES BUSINESS SEGMENT AA4-011 FIXED LOAD COMMODITY AA5-002 TERRAIN/DUTY:100%(ALL)OF THE TIME,IN TRANSIT,IS SPENT ON PAVED ROADS AB1-008 MAXIMUM 8%EXPECTED GRADE AB5-001 SMOOTH CONCRETE OR ASPHALT PAVEMENT - MOST SEVERE IN-TRANSIT (BETWEEN SITES) ROAD SURFACE 995-091 MEDIUM TRUCK WARRANTY A66-99D EXPECTED FRONT AXLE(S) LOAD:10000.0 lbs A68-99D EXPECTEDREAR DRIVE AXLE(S)LOAD : 12000.0 lbs A63-99D EXPECTED GROSS VEHICLE WEIGHT CAPACITY :22000.0 lbs Application Version 8.9.003 01/11/2016 3"24PM Data Version PRL-10M.011 2017 Newport Beach Fire Page 2of 15 14-157 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City, OH 43123 Phone:614-539-8181 Data Code Truck Service AA3-024 A88-99D AF7-99D Description AMBULANCE BODY EXPECTED TRUCK BODY LENGTH :16.0 ft EXPECTED BODY/PAYLOAD CG HEIGHT ABOVE FRAME "XX"INCHES :32.0 in Engine 101-2N6 CUM ISB 6.7-280 280 HP 660 LB/FT @ 1600 RPM Electronic Parameters 2300 RPM,2600 GOV, 79A-075 79B-000 79K-007 79M-001 79P-002 79Q-003 79U-007 80G-002 80J-002 Engine Equipment 99C-016 99D-012 13E-001 105-001 133-004 014-099 124-1CE 292-058 290-017 281-001 75 MPH ROAD SPEED LIMIT CRUISE CONTROL SPEED LIMIT SAME AS ROAD SPEED LIMIT PTO MODE ENGINE RPM LIMIT -1100 RPM PTO MODE BRAKE OVERRIDE -SERVICE BRAKE APPLIED PTO RPM WITH CRUISE SET SWITCH -700 RPM PTO RPM WITH CRUISE RESUME SWITCH -800 RPM PTO GOVERNOR RAMP RATE -250 RPM PER SECOND PTO MINIMUM RPM -700 REGEN INHIBIT SPEED THRESHOLD - 5 MPH 2016 ONBOARD DIAGNOSTICS/2010 EPA/CARB/GHG14 2008 CARB EMISSION CERTIFICATION - EXEMPTED VEHICLE;NO CLEAN IDLE LABEL REQUIRED STANDARD OIL PAN ENGINE MOUNTED OIL CHECK AND FILL ONE PIECE VALVE COVER SIDE OF HOOD AIR INTAKE WITH FIREWALL MOUNTED DONALDSON AIR CLEANER LN 12V 320 AMP 4962PA PAD MOUNT ALTERNATOR (3) ALLIANCE MODEL 1031,GROUP 31, 12 VOLT MAINTENANCE FREE 2280 CCA THREADED STUD BATTERIES BATTERY BOX FRAME MOUNTED STANDARD BATTERY JUMPERS Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire Weight Front 10 40 Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA,Wl 541309559 Phone:920-766-5222 Weight Rear 20 01/11/2016 3:24 PM Page 3 of 15 14-158 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City, OH 43123 Phone:614-539-8181 Data Code Description 282-042 LH BATTERY BOX MOUNTED AS FAR AFT AS POSSIBLE,NO GREATER THAN 60 INCHES BACK OF CAB 291-017 WIRE GROUND RETURN FOR BATTERY CABLES WITH ADDITIONAL FRAME GROUND RETURN 289-001 NON-POLISHED BATTERY BOX COVER 107-032 CUMMINS TURBOCHARGED 18.7 CFM AIR COMPRESSOR WITH INTERNAL SAFETY VALVE 108-002 STANDARD MECHANICAL AIR COMPRESSOR GOVERNOR 131-013 AIR COMPRESSOR DISCHARGE LINE 152-039 GVG,FIRE AND EMERGENCY SERVICE VEHICLES ENGINE WARNING 128-1AR CUMMINS EXHAUST BRAKE INTEGRAL WITH VARIABLE GEOMETRY TURBO WITH ON/OFF DASH SWITCH,ACTIVATES STOP LAMPS 016-1DD RH OUTBOARD UNDER STEP MOUNTED HORIZONTAL AFTERTREATMENT SYSTEM ASSEMBLY WITH LH HORIZONTAL TAILPIPE EXITING FORWARD OF REAR TIRES 28F-007 ENGINE AFTERTREATMENT DEVICE, AUTOMATIC OVER THE ROAD ACTIVE REGENERATION AND DASH MOUNTED SINGLE REGENERATION REQUEST/INHIBIT SWITCH 239-001 STANDARD EXHAUST SYSTEM LENGTH 237-027 LH HORIZONTAL TAILPIPE,EXIT FORWARD OF REAR TIRES 23U-001 6 GALLON DIESEL EXHAUST FLUID TANK 30N-003 100 PERCENT DIESEL EXHAUST FLUID FILL 43X-002 LH MEDIUM DUTY STANDARD DIESEL EXHAUST FLUID TANK LOCATION 23Y-001 STANDARD DIESEL EXHAUST FLUID PUMP MOUNTING 43Y-001 STANDARD DIESEL EXHAUST FLUID TANK CAP 273-035 HORTON HT650 FRONTAL AIR ON/OFF ENGINE FAN CLUTCH 276-002 AUTOMATIC FAN CONTROL WITH DASH SWITCH AND INDICATOR LIGHT,NON ENGINE MOUNTED 110-003 CUMMINS SPIN ON FUEL FILTER 118-001 FULL FLOW OIL FILTER 266-078 950 SQUARE INCH ALUMINUM RADIATOR 103-036 ANTIFREEZE TO -34F.ETHYLENE GLYCOL PRE- CHARGED SCA HEAVY DUTY COOLANT Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire Weight Front 15 20 Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA.Wl 541309559 Phone:920-766-5222 Weight Rear 15 20 01/11/2016 3:24 PM Page 4 of 15 14-159 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City, OH 43123 Phone:614-539-8181 Data Code 171-007 172-001 270-016 168-002 138-010 140-022 134-001 132-004 155-058 Transmission 342-1 MR Description GATES BLUE STRIPE COOLANT HOSES OR EQUIVALENT CONSTANT TENSION HOSE CLAMPS FOR COOLANT HOSES RADIATOR DRAIN VALVE LOWER RADIATOR GUARD PHILLIPS-TEMRO 750 WATT/115 VOLT BLOCK HEATER CHROME ENGINE HEATER RECEPTACLE MOUNTED UNDER LH DOOR ALUMINUM FLYWHEEL HOUSING ELECTRIC GRID AIR INTAKE WARMER DELCO 12V 38MT HD STARTER WITH INTEGRATED MAGNETIC SWITCH ALLISON 2200 EVS AUTOMATIC TRANSMISSION WITH PARK PAWL WITH PTO PROVISION Transmission Equipment 343-303 ALLISON VOCATIONAL PACKAGE 364 - AVAILABLE ON 1000/2000 PRODUCT FAMILIES WITH VOCATIONAL MODEL EVS 84B-003 ALLISON VOCATIONAL RATING FOR FIRE TRUCK/EMERGENCY VEHICLE APPLICATIONS AVAILABLE WITH ALL PRODUCT FAMILIES 84C-003 PRIMARY MODE GEARS,5 FORWARD GEARS WITH MANUAL SELECTION FOR 3, 2 AND 1, AVAILABLE FOR 1000/2000 PRODUCT FAMILIES ONLY 84N-000 NEUTRAL AT STOP -DISABLED,FUELSENSE - DISABLED 84U-000 DRIVER SWITCH INPUT -DEFAULT -NO SWITCHES 353-022 VEHICLE INTERFACE WIRING CONNECTOR WITHOUT BLUNT CUTS,AT BACK OF CAB 34C-001 ELECTRONIC TRANSMISSION CUSTOMER ACCESS CONNECTOR FIREWALL MOUNTED 362-1BV CUSTOMER INSTALLED CHELSEA 270 SERIES PTO 363-001 PTO MOUNTING,LH SIDE OF MAIN TRANSMISSION 341-018 MAGNETIC PLUGS,ENGINE DRAIN, TRANSMISSION DRAIN, AXLE(S) FILLAND DRAIN Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire Weight Front Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA,Wl 541309559 Phone:920-766-5222 Weight Rear 01/11/2016 3:24 PM Page 5 of 15 14-160 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City, OH 43123 Phone:614-539-8181 Data Code Description 345-074 DASH MOUNTED T-HANDLE CABLE SHIFT CONTROL WITH PARK POSITION FOR INTERNAL PARK PAWL 97G-006 TRANSMISSION PROGNOSTICS -DISABLED (N/A)2013,FOR USE IN 1000/2000 ONLY 370-015 WATER TO OILTRANSMISSION COOLER, IN RADIATOR END TANK 346-001 TRANSMISSION OIL CHECK AND FILL 35T-001 SYNTHETIC TRANSMISSION FLUID (TES-295 COMPLIANT) Front Axle and Equipment 400-1A5 402-021 403-026 419-023 409-021 408-001 416-022 405-003 536-050 539-003 534-015 40T-001 Front Suspension 620-1E9 619-005 629-004 410-001 Rear Axle and Equipment 420-1C6 421-410 DETROIT DA-F-10.0-3 10,000#FF1 71.5 KPI/3.74 DROP SINGLE FRONT AXLE MERITOR 15X5 Q+CAST SPIDER CAM FRONT BRAKES,DOUBLE ANCHOR,FABRICATED SHOES FIRE AND EMERGENCYSEVERE SERVICE, NON-ASBESTOS FRONT LINING CONMET CAST IRON FRONT BRAKE DRUMS SKF SCOTSEAL PLUS XL FRONT OIL SEALS VENTEDFRONT HUBCAPS WITHWINDOW, CENTER AND SIDE PLUGS -OIL STANDARD SPINDLE NUTS FOR ALL AXLES HALDEX AUTOMATIC FRONT SLACK ADJUSTERS TRW THP-60 POWER STEERING POWER STEERING PUMP 2 QUART SEE THROUGH POWER STEERING RESERVOIR ORGANIC SAE 80/90 FRONT AXLE LUBE 12,000#MONO TAPERLEAF FRONT SUSPENSION MAINTENANCE FREE RUBBER BUSHINGS - FRONT SUSPENSION FRONT SWAYBAR FRONT SHOCK ABSORBERS DETROIT DA-RS-17.5-2 17,500#R-SERIES SINGLE REAR AXLE 4.10 REAR AXLE RATIO Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire Weight Front 60 30 Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA, Wl 541309559 Phone:920-766-5222 Weight Rear -170 01/11/2016 3:24 PM Page 6 of 15 14-161 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City, OH 43123 Phone:614-539-8181 Data Code 424-001 386-079 423-028 433-025 434-005 451-023 440-006 426-074 428-003 41T-001 Rear Suspension 622-1CX 621-046 431-001 888-056 87D-015 910-009 623-002 630-006 439-004 Brake System 018-002 490-100 Description IRON REAR AXLE CARRIER WITH STANDARD AXLE HOUSING MXL 16T MERITOR EXTENDED LUBE MAIN DRIVELINE WITH HALF ROUND YOKES MERITOR 15X8.62 Q+CAST SPIDER CAM REAR BRAKES,DOUBLE ANCHOR,FABRICATED SHOES FIRE AND EMERGENCY SEVERE SERVICE NON- ASBESTOS REAR BRAKE LINING BRAKE CAMS AND CHAMBERS ON FORWARD SIDE OF DRIVE AXLE(S) WITH AUXILIARY SUPPORT BRACKETS CONMET CAST IRON REAR BRAKE DRUMS REAR OIL SEALS HALDEX GOLDSEAL LONGSTROKE 1-DRIVE AXLE SPRING PARKING CHAMBERS HALDEX AUTOMATIC REAR SLACK ADJUSTERS ORGANIC SAE 80/90 REAR AXLE LUBE AIRLINER 12,000#REAR SUSPENSION AIRLINER MID POSITION RIDE HEIGHT STANDARD AXLE SEATS IN AXLE CLAMP GROUP IGNITION CONTROLLED ELECTRIC DUMP SWITCH FOR AIR SUSPENSION WITH AUTOFILL OVERRIDE VALVE REAR AIR SUSPENSION DUMP VALVE WITH AUTOFILL FOR IGNITION OFF AND >5 MPH, LIGHT,BUZZER,BODY SWITCH WIRING AND OVERRIDE CONTROL DUAL INSTANT RESPONSE REAR SUSPENSION LEVELING VALVES WITH PING TANK AND RESERVE TANK FOR 10/12/15,000#AIRLINER TRANSVERSE CONTROL RODS 10,000/15,000#AIRLINER REAR SUSPENSION STABILIZER BAR REAR SHOCK ABSORBERS - ONE AXLE(AIR RIDE SUSPENSION) AIR BRAKE PACKAGE WABCO 4S/4M ABS WITHOUT TRACTION CONTROL Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire Weight Front -20 20 Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA,Wl 541309559 Phone:920-766-5222 Weight Rear -20 -20 -40 40 50 01/11/2016 3:24 PM Page 7 of 15 14-162 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City, OH 43123 Phone:614-539-8181 Data Code Description 871-001 REINFORCED NYLON,FABRIC BRAID AND WIRE BRAID CHASSIS AIR LINES 904-001 FIBER BRAID PARKING BRAKE HOSE 412-001 STANDARD BRAKE SYSTEM VALVES 46D-002 STANDARD AIR SYSTEM PRESSURE PROTECTION SYSTEM 413-002 STD U.S.FRONT BRAKE VALVE 432-003 RELAY VALVEWITH 5-8 PSI CRACK PRESSURE, NO REAR PROPORTIONING VALVE 480-086 BW AD-9SI BRAKE LINE AIR DRYER WITH HEATER 479-012 AIR DRYER MOUNTED UNDER HOOD 460-008 STEEL AIR BRAKE RESERVOIRS MOUNTED INSIDE RAIL 607-001 CLEAR FRAME RAILS FROM BACK OF CAB TO FRONT REAR SUSPENSION BRACKET,BOTH RAILS OUTBOARD Weight Front Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA,Wl 541309559 Phone:920-766-5222 Weight Rear 477-006 BW DV-2 AUTO DRAIN VALVE WITHOUT HEATER ON ALLTANK(S) Trailer Connections 335-004 32A-002 UPGRADED CHASSIS MULTIPLEXING UNIT UPGRADED BULKHEAD MULTIPLEXING UNIT Wheelbase &Frame • 545-442 4425MM (174 INCH)WHEELBASE 546-094 9/32X3-7/16X10-1/16 INCH STEEL FRAME (7.14MMX255.6/0.281X10.06 INCH)80KSI 552-030 1600MM (63 INCH) REAR FRAME OVERHANG 55W-006 FRAME OVERHANG RANGE:61 INCH TO 70 INCH AC8-99D CALC'DBACKOF CABTO REAR SUSP C/L (CA): 108.45 in AE8-99D CALCULATED EFFECTIVE BACK OF CAB TO REAR SUSPENSION C/L (CA):105.45 in AE4-99D CALC'D FRAME LENGTH -OVERALL :266.39 AM6-99D -CALC'D SPACE AVAILABLE FOR DECKPLATE : 108.45 in FSS-0LH CALCULATED FRAME SPACE LH SIDE :120.04 in FSS-0RH CALCULATED FRAME SPACE RH SIDE :121.66 in 553-001 SQUARE END OF FRAME 550-001 FRONT CLOSING CROSSMEMBER Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire -60 -10 01/11/2016 3:24 PM Page 8 of 15 14-163 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City, OH 43123 Phone:614-539-8181 Data Code Description Weight Front 559-001 STANDARD WEIGHT ENGINE CROSSMEMBER 562-001 STANDARD MIDSHIP #1 CROSSMEMBER(S) 572-001 STANDARD REARMOST CROSSMEMBER 565-001 STANDARD SUSPENSION CROSSMEMBER Chassis Equipment 556-1AR THREE-PIECE 14 INCH CHROMED STEEL BUMPER WITH COLLAPSIBLE ENDS 30 558-001 FRONT TOW HOOKS -FRAME MOUNTED 15 574-001 BUMPER MOUNTING FOR SINGLE LICENSE PLATE 586-024 FENDER AND FRONT OF HOOD MOUNTED FRONT MUDFLAPS 551-017 GRADE 8 THREADED HEX HEADED FRAME FASTENERS INSTALLED WITH BOLT HEADS ON OUTSIDE OF FRAME Fuel Tanks 204-217 34 GALLON/128 LITER SHORT RECTANGULAR ALUMINUM FUEL TANK - LH 218-005 RECTANGULARFUELTANK(S) 215-005 PLAIN ALUMINUM/PAINTED STEEL FUEL/HYDRAULIC TANK(S) WITH PAINTED BANDS 212-007 FUEL TANK(S)FORWARD 664-001 PLAIN STEP FINISH 205-001 FUEL TANK CAP(S) 122-084 ALLIANCE FUEL FILTER/WATER SEPARATOR WITH PRIMER PUMP 216-020 EQUIFLO INBOARD FUEL SYSTEM 202-016 HIGH TEMPERATURE REINFORCED NYLON Tires Hubs 093-0E5 094-1 FT 418-056 450-056 Wheels FUEL LINE MICHELIN XZE 245/70R19.5 16 PLY RADIAL FRONT TIRES MICHELIN XDS2 245/70R19.5 16 PLY RADIAL REAR TIRES CONMET PRESET PLUS IRON FRONT HUBS CONMET PRESET PLUS IRON REAR HUBS Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire -82 Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA,Wl 541309559 Phone:920-766-5222 Weight Rear -144 01/11/2016 3:24 PM Page 9 of 15 14-164 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City, OH 43123 Phone:614-539-8181 Data Code 502-1E5 505-1E5 524-001 525-001 52M-004 496-011 497-011 Cab Exterior 829-071 650-009 678-018 646-023 65X-003 644-004 690-002 727-1B1 726-002 728-002 657-001 575-001 312-038 302-047 311-019 294-021 300-015 744-1BC 797-001 796-001 Description ALCOA 77362X 19.5X7.50 10-HUB PILOT 5.23 INSET ALUMINUM DISC FRONT WHEELS ALCOA 77362X 19.5X7.50 10-HUB PILOT ALUMINUM DISC REAR WHEELS POLISHED FRONT WHEELS;OUTSIDE ONLY POLISHED REAR WHEELS;OUTSIDE OF OUTER WHEELS ONLY FORCEMATCH TIRE/WHEEL RUNOUT CHECK/MARK AND STATIC BALANCING -ALL TIRES/WHEELS FRONT WHEEL MOUNTING NUTS REAR WHEEL MOUNTING NUTS 106 INCH BBC FLAT ROOF ALUMINUM CONVENTIONAL CAB RUBBER CAB MOUNTS LH AND RH EXTERIOR GRAB HANDLES WITH SINGLE RUBBER INSERT HOOD MOUNTED CHROMED PLASTIC GRILLE CHROME HOOD MOUNTED AIR INTAKE GRILLE FIBERGLASS HOOD TUNNEL/FIREWALL LINER DUAL 25 INCH ROUND STUTTER TONE HOOD MOUNTED AIR HORNS WITH DUAL LANYARDS DUAL ELECTRIC HORNS DUAL HORN SHIELDS DOOR LOCKS AND IGNITION SWITCH KEYED THE SAME REAR LICENSE PLATE MOUNT END OF FRAME INTEGRAL HEADLIGHT/MARKER ASSEMBLY WITH CHROME BEZEL LED AERODYNAMIC MARKER LIGHTS HEADLIGHTS ON WITH WIPERS,WITH DAYTIME RUNNING LIGHTS TRUCK-LITE 3 CHAMBER MODULES WITH 45 SERIES SEALED BEAM LAMPS STANDARD FRONT TURN SIGNAL LAMPS DUAL WEST COAST BRIGHT FINISH HEATED MIRRORS WITH LH AND RH REMOTE DOOR MOUNTED MIRRORS 102 INCH EQUIPMENT WIDTH Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire Weight Front -64 Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA,Wl 541309559 Phone:920-766-5222 Weight Rear -128 01/11/2016 3:24 PM Page 10 of 15 14-165 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City, OH 43123 Phone:614-539-8181 Data Code 743-204 74A-001 729-001 768-998 661-004 654-027 663-019 659-019 Cab Interior 707-1AK 706-016 708-016 772-006 691-014 694-010 742-007 680-006 860-004 700-002 701-001 703-005 170-015 130-036 702-002 739-034 285-013 280-007 Description LH AND RH 8 INCH BRIGHT FINISH CONVEX MIRRORS MOUNTED UNDER PRIMARY MIRRORS RH DOWN VIEW MIRROR STANDARD SIDE/REAR REFLECTORS NO REAR WINDOW TINTED DOOR GLASS LH AND RH WITH TINTED OPERATING WING WINDOWS RH AND LH ELECTRIC POWERED WINDOWS, PASSENGER SWITCHES ON DOOR(S) 1-PIECE TINTED ROPED-IN WINDSHIELD 2 GALLON WINDSHIELD WASHER RESERVOIR WITHOUT FLUID LEVEL INDICATOR,FRAME MOUNTED OPAL GRAY VINYL INTERIOR MOLDED DOOR PANEL WITH UPPER VINYL INSERTS MOLDED DOOR PANEL WITH UPPER VINYL INSERTS BLACK MATS WITH SINGLE INSULATION FORWARD ROOF MOUNTED CONSOLE WITH UPPER STORAGE COMPARTMENTS AND ADDITIONAL CENTER COMPARTMENT WITHOUT NETTING IN DASH STORAGE BIN (2)CUP HOLDERS LH AND RH DASH GRAY/CHARCOAL FLAT DASH SMART SWITCH EXPANSION MODULE HEATER,DEFROSTER AND AIR CONDITIONER STANDARD HVAC DUCTING MAIN HVAC CONTROLS WITH RECIRCULATION SWITCH STANDARD HEATER PLUMBING (1) DENSO HEAVYDUTYAND(1) SANDEN COMPACT REFRIGERANT COMPRESSORS BINARY CONTROL,R-134A PREMIUM INSULATION SOLID-STATE CIRCUIT PROTECTION AND FUSES 12V NEGATIVE GROUND ELECTRICAL SYSTEM Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire Weight Front -20 20 Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA,Wl 541309559 Phone:920-766-5222 Weight Rear 01/11/2016 3:24 PM Page 11 of 15 14-166 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City, OH 43123 Phone:614-539-8181 Data Code Description 324-011 DOME DOOR ACTIVATED LH AND RH, DUAL READING LIGHTS,FORWARD CAB ROOF 655-005 LH AND RH ELECTRIC DOOR LOCKS 284-023 (1)12 VOLT POWER SUPPLY INDASH 756-1D9 PREMIUM HIGH BACK AIR SUSPENSION DRIVER SEAT WITH 3 CHAMBER AIR LUMBAR, INTEGRATED CUSHION EXTENSION,FORWARD AND REAR CUSHION TILT,ADJUSTABLE SHOCK ABSORBER 760-1D9 PREMIUM HIGH BACK AIR SUSPENSION PASSENGER SEAT WITH 3 CHAMBER AIR LUMBAR,INTEGRATED CUSHION EXTENSION,FORWARD AND REAR CUSHION TILT,ADJUSTABLE SHOCK ABSORBER 711-004 LH AND RH INTEGRAL DOOR PANEL ARMRESTS 758-033 VINYL WITH CLOTH INSERT DRIVER SEAT 761-033 VINYL WITH CLOTH INSERT PASSENGER SEAT 763-012 3 POINT HIGH VISIBILITY ORANGE RETRACTOR DRIVER AND PASSENGER SEAT BELTS 532-002 ADJUSTABLE TILT AND TELESCOPING STEERING COLUMN 540-015 4-SPOKE 18 INCH (450MM)STEERING WHEEL 765-002 DRIVER AND PASSENGER INTERIOR SUN VISORS Instruments &Controls 732-003 734-003 87L-003 870-001 486-001 840-002 198-003 149-013 156-007 811-042 WOODGRAIN DRIVER INSTRUMENT PANEL WOODGRAIN CENTER INSTRUMENT PANEL ENGINE REMOTE INTERFACE WITH PARK BRAKE AND NEUTRAL INTERLOCKS BLACK GAUGE BEZELS LOW AIR PRESSURE INDICATOR LIGHT AND AUDIBLE ALARM 2 INCH PRIMARY AND SECONDARY AIR PRESSURE GAUGES DASH MOUNTED AIR RESTRICTION INDICATOR WITH GRADUATIONS ELECTRONIC CRUISE CONTROL WITH SWITCHES IN LH SWITCH PANEL KEY OPERATED IGNITION SWITCH AND INTEGRAL START POSITION;4 POSITION OFF/RUN/START/ACCESSORY ICU3S,132X48 DISPLAY WITH DIAGNOSTICS,28 LED WARNING LAMPS AND DATA LINKED Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire Weight Front 70 60 10 Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA, Wl 541309559 Phone:920-766-5222 Weight Rear 20 01/11/2016 3:24 PM Page 12 of 15 14-167 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City, OH 43123 Phone:614-539-8181 Data Code Description 160-038 HEAVY DUTY ONBOARD DIAGNOSTICS INTERFACE CONNECTOR LOCATED BELOW LH DASH 844-001 2 INCH ELECTRIC FUEL GAUGE 148-070 ENGINE REMOTE INTERFACE WITH PRESET FAST IDLE 163-004 ENGINE REMOTE INTERFACE CONNECTOR IN ENGINE COMPARTMENT 856-001 ELECTRICAL ENGINE COOLANT TEMPERATURE GAUGE 864-001 2 INCH TRANSMISSION OIL TEMPERATURE GAUGE 830-017 ENGINE AND TRIP HOUR METERS INTEGRAL WITHIN DRIVER DISPLAY 73B-998 NO LANE DEPARTURE WARNING SYSTEM 852-002 ELECTRIC ENGINE OIL PRESSURE GAUGE 746-1B0 AM/FM/WB RADIO WITH CD PLAYER, BLUETOOTH AND MICROPHONE,USB,FRONT AND REAR AUXILIARY INPUTS AND J1939 747-001 DASH MOUNTED RADIO 750-002 (2) RADIO SPEAKERS INCAB 753-001 AM/FM ANTENNA MOUNTED ON FORWARD LH ROOF 810-027 ELECTRONIC MPH SPEEDOMETER WITH SECONDARY KPH SCALE,WITHOUT ODOMETER 817-001 STANDARD VEHICLE SPEED SENSOR 812-001 ELECTRONIC 3000 RPM TACHOMETER 162-002 IGNITION SWITCH CONTROLLED ENGINE STOP 264-032 (2) OVERHEAD MOUNTED LANYARD CONTROLS: (1)OFFICER AIR HORN AND (1) DRIVER AIR HORN 836-015 DIGITAL VOLTAGE DISPLAY INTEGRAL WITH DRIVER DISPLAY 660-008 SINGLE ELECTRIC WINDSHIELD WIPER MOTOR WITH DELAY 304-001 MARKER LIGHT SWITCH INTEGRAL WITH HEADLIGHT SWITCH 882-009 ONE VALVE PARKING BRAKE SYSTEM WITH WARNING INDICATOR 299-013 SELF CANCELING TURN SIGNAL SWITCH WITH DIMMER,WASHER/WIPER AND HAZARD IN HANDLE Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire Weight Front 10 Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA,Wl 541309559 Phone:920-766-5222 Weight Rear 01/11/2016 3:24 PM Page 13 of 15 14-168 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City, OH 43123 Phone:614-539-8181 Data Code Description 298-039 INTEGRAL ELECTRONIC TURN SIGNAL FLASHER WITH HAZARD LAMPS OVERRIDING STOP LAMPS Weight Front Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA,Wl 541309559 Phone:920-766-5222 Weight Rear 869-998 NO MISCELLANEOUS GAUGES Design 065-000 PAINT:ONE SOLID COLOR Color 980-5F6 CAB COLOR A:L0006EB WHITE ELITE BC 986-020 BLACK,HIGH SOLIDS POLYURETHANE CHASSIS PAINT 98K-998 NO FUEL TANK CABINET PAINT 963-003 STANDARD E COAT/UNDERCOATING Certification /Compliance 996-001 U.S.FMVSS CERTIFICATION,EXCEPT SALES CABS AND GLIDER KITS Secondary Factory Options 998-001 CORPORATE PDI CENTER IN-SERVICE ONLY 999-PDI LIQUID SPRING CONVERSION AT KAFFENBARGER IN NEW CARLISLE. .TOTAL VEHICLE SUMMARY Weight Summary Factory Weight"*" Total Weight+ Weight Front 5945 lbs 5945 lbs Extended Warranty WAG-052 TOWING EXTENDED/ROADSIDE SERVICE WARRANTY,1 YEAR/UNLIMITED MILES/KM,$550 CAP Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire Weight Rear 3141 lbs 3141 lbs Total Weight 9086 lbs 9086 lbs 01/11/2016 3:24 PM Page 14 of 15 14-169 Prepared for: Jason Cavallo Horton Emergency Vehicles 3800 McDowell Rd Grove City,OH 43123 Phone:614-539-8181 (+) Weights shown are estimates only. Ifweight is critical,contact Customer ApplicationEngineering. Application Version 8.9.003 Data Version PRL-10M.011 2017 Newport Beach Fire Prepared by: TRUCK CTY OF WISCONSIN, INC. 2401 PROGRESS WAY KAUKAUNA,Wl 541309559 Phone:920-766-5222 01/11/2016 3:24 PM Page 15 of 15 14-170 Clarification Leader will be accommodating the mid-point inspection at the HALCORE Leader Industries ambulance production facility located in South El Monte CA. While the body blank will be produced and mounted at our HALCORE body plant in Grove City Ohio, Leader South El Monte is a final stage ambulance converter with a full capabilities production facility. This includes a full metal shop,full paint shop electrical and cabinet shops. This facility has full capabilityto respond to any body build issues on site in CA. 14-171 EXHIBIT C WARRANTY Halcore Group,Inc.,DBA Leader Industries Page C-1 14-172 ATTACHMENT:WARRANTY INFORMATION The pr oposal s hall i nclude al Iw arranties t hat ar e r equired i nt he Ambulance specification.Lifetime warranties will not be accepted because of their unclear nature of duration.All warranties must have specific time durations and shall define warranties on specific components.The minimum acceptable warranty periods are noted below. In the blank lines the Proposer shall note the termsofthe warranties that apply to the manufacturer being proposed. CONVERSION STRUCTURAL WARRANTY: 15 years/150,000 Miles Proposed warranty term:Years 15 /15Q»QQQ Miles Note:The structural warranty,as noted in the structural section of this specification,will include all interior cabinet construction.These terms and conditions must be explicitly stated in the manufacturer's warranty certificate. Doest he s tructural warranty pr oposed c omply w ith t he above-stated terms an d conditions?Yes x No ELECTRICAL WARRANTY:5 years/Unlimited Miles Proposed warranty term:JL Year(s),Unlimited Miles PAINT WARRANTY:7 Years/150,000 Miles Proposed warranty term:Year(s),;Miles For verification of the completed warranty terms stated above the bidder must include printed manufacturer's warranty certificates that meet or exceed the minimum required periods stated above. v Are the manufacturers warranties included?Yes No Warranties s hall not be pr o-rated in any manner and s hall be t ransferable for t heir duration. All warranties shall be from the manufacturer as op posed to a distributoror service center. 14-173 LEADER OWNER SERVICE POLICY Leader In dustries WARRANTY -Leader Industries,the manufacturer (herein referred to as "Leader")warrants to the original retail purchaser that each newLeader Ambulanc e Conversion and all equipment and accessories attached there to which are manufactured by Leader are free from defects in material and workmanship under normal use and service with regular maintenance s ervice during the time and mileage limits and owner service hereinafter set forth. CHASSIS - The chassis ofyour new ve hide is warranted by its manufacturer,as set out in your New Vehicl e Warranty and Owner Protection Plan, which c learly outlines such warranties. These warranties are made solely by Chass is Manufacturer and not by Leader or its Distributors. LIMITATIONS TIME AND MILEAGE -Leader warranty applies to the Leader Ambulance Conversion and all equipment and attached there to whichare manufactured by Leader for 36 months after date of delivery to the original retail purchaser or36,000 miles, whichever first occurs.The exclusive remedy for any such defects shall be the obligations of Leader and limitedto repairing or replacing byLeaderas its option any partorpartsof the body which uponexamination byLeadershalldisclose to its satisfaction to have been thus defective,provided that such part or parts are returnedto itsfa ctory forsuch inspection with transportation charges prepaid. This warrantyshall not apply to any part which has been repaired or alteredoutsideofLeader's factory in anyway which,in the judgmentof Leader, affectsits stability a nd reliab ility or to any part subject to misuse, negligenceoraccident.Thiswarr antydoes not apply totires, wheel alignment or balanc ing,engine tune-up,or to replacementor parts ordinarily made as partof normal service. BODY ADJUSTME NTS AND REP AIRS-Leader s hall not be responsible forany body repairs or adjustments that have not been duly authorized byitsaut horized factory servic e representatives.If need for such work arises, contactthe Leader Distributor inyour locality or the Leader factory service department and furnish a detailed reportofyour complaint. 14-174 LEADER Policy on Leader Owner Service 1.DEMONSTRATO RS-On a Leader Distributor-owned demonstrator,the warranty time and mileage limitations are calculated from the date the vehicle is first placed in s ervice by such Distributor. 2.PAINT AND OTHER APPE RANCE ITEMS-Imperfections in paint, trim or other appearance items are normally apparent and are corrected during the new vehi cle pre-delivery conditioning. For your protection,we suggest that you ifyou find any paint or appearance imperfections,call it to the attention of your Leader Distributor within 21 days,as normal deterioration due to use and exposure is covered by the Leader warranty. 3.DOWN TIME-The provisions of the Leader warranty do not provide for any liab ility on the part of Leader and/or its distributors for any other cost s,expenses or damage incurred by an owner while a vehicle is o ut of service during fulfillment of any warranty,special policy or campaign adjustments. 4.PRODUCT IMPROVEMENT-Leader,in its continuous product improvement program,reserves the right to change specifications without notice at any time with out incur ring any obligation to make the same or similar c hanges on previously manufactured units. EXCLUSIONS THIS WARRANTY SHALL NOT APPLY TO: 1. Any vehicle on which the odometer mileage has been altered and the vehicle's actual mileage cannot be readily determined. 2.Normal maintenance services (such as lubrication of hinges, oils,wheel alignment and balanc ing,alignment of doors, windows,fenders,hood,grille,and bumpers). 3. Any additional and/or alteration to the el ectrical system will make null and void your Leader warranty on the complej e electrical system. 4.Installation of customer's electrical equipment and/or property or any other part of the vehic le resulting f rom the use of the customer's property. 5. Any part of any vehicle which has been subject to misuse, negligence,alteration,or accide nt or whic h shall have been repaired outside so as in any way in the reasonable judgment of Leader,to affect adversely its performance and reliability. 6.Normal deterioration of soft trim and external appearance items due to wear and exposure. 7.The repair or replacement of any part,the failure of which is caused by lack of performance of maintenance. 8.Paint failures result ing from expos ure to climate c onditions (such as ice and dust control agents,water spots,tree sap,and stone chips). 9.Paint damage due to improper pr otection of finis h during storage and/or use,rubbing th rough caused by improper polishing procedures , or the us e of improper polishing or cleaning materials. 10.Parts of material (such as bumpers,grilles,moldings, chrome parts and paint)damaged by ice-melting agents used on highways,roads,and streets. 14-175 LEADER INDUSTRIES PREMIUM CONVERSION STRUCTURAL LIMITED 15 YEAR 150,000 MILE WARRANTY Subject to the provisions,limitations and conditions set forth herein,Leader Industries hereby warrants to each original purchaser that each new modular ambulance body (Exclusive of paint finish,hardware,moldings,windows, and other appointments and accessories)is structurally sound and free ofall structural defects of both material and workmanship.Leader Industries further warrants that each such body will maintain its structural integrity for a period of fifteen (15)years from the date of manufacture,as designated on the manufacturer's certification plate attached there to, or 150,000 miles whicheveroccurs first,subject to the terms andconditionsbelow. Leader Industries warrants that the exterior doors and exterior door hinges of each such modular body are structurally sound and will remain free if joint separation,cracks,and all other structural defects for said fifteen (15)year/150,000 mile period,and that all such exterior doors will remain in proper adjustment during said fifteen (15)year or 150,000 mile period. Leader Industries further warrants that the interior cabinets,cabinetdoors and ceiling of each such modular body are structurally sound and will remain free structural defects for said fifteen (15)year/150,000 mile period,and that all such cabinets will remain structurally attached and inproper position during said fifteen (15)year/150,000 mile period. Should the ambulance body be re-chassied by Leader Industries during the original warranty period,the structural warranty set forth above will be revalidated for an additional five years from the expiration of the original warranty period.If the ambulance body is re-chassied by Leader Industries a second or subsequent time during the original or any extended warranty period,Leader Industries will extend this structural warranty to five additional years from the dateon which the body islast re-chassied,provided that necessary repairs are authorized bythe owner and performed by Leader Industries.The opportunity to extend this warranty will remain in effect for the life of the body and is subject tothe conditions that I)the re-chassied work must be performed by Leader Industries and 2)that the re-chassied work must be completed during the original or an extended warranty period.Any re- chassied or modification work performed onthe body byanother party will immediately and permanently void this warranty. This warranty is conditioned upon I)normal use and reasonable maintenance of such modular body and covered attachments as recommended by Leader Industries 2) prompt written notice of all defects to Leader Industries or its authorized dealerinthe owner's area, and 3)all repairs modifications,and additions there to being performed by Leader Industries ora party authorized by it.This warranty does not extend to,and will not cover defects or conditions resulting from misuse,negligence,accident,or overloading beyond applicable weight ratings.Upon the failure to satisfy any such condition,this warranty shall become void and unenforceable. Should repairs become necessary under the terms of this warranty,the extent of that repair shall be determined solely by Leader Industries and shall be performed solely by Leader Industries or a repair facility designated by Leader Industries.The expense of any transportation to or from such repair facility shall beforthe account owner and is not covered by this warranty. Leader Industries reserves the unrestricted right at any time and from the time to make changes inthe design of, and/or improvements on its products without thereby imposing any obligation on itself to make corresponding changes or improvements in or onits products there tofor manufactured. LEADER INDUSTRIES 10941 Weaver Ave.,South El Monte,CA 91733 14-176 LEADER INDUSTRIES ELECTRICAL SYSTEMS WARRANTY 5 YEAR -UNLIMITED MILES Leader Industries (LI)herebywarrantsto each original purchaserofa Type I,Type II or Type III ambulance manufactured by LI incorporating Li's Series RMR Rail System,W7 LED Diagnostics,and single relay control boards.This is a fully integrated relaycontrol board designed andbuiltto IPC Class 3*guidelines andthat the solid state componentsofsuch system,including allcircuit boards, circuit board components, andcircuit board connectors,shall be free ofdefects in material and workmanship,including loose connections,fora periodof Five (5)yearsfromthe dateof manufacture,as designated on the manufacturer's certification plate attached thereto. Specifically included in this warranty are the following: • Switches Circuit Breakers Relays •Component boards Solenoids Indicators The stationary wiring harness in such ambulance is warranted to be free of defects in materials and workmanship, including broken wires,chafed or pinched wires,and defective splices,for a periodof Five (5) yearsfrom such date of manufacture.The harness includes that part of the wiring which is mounted inthe modular or Type II body,up to and including the termination pointsat the distribution boards or at accessory items. LeaderIndustriesextends a 2 year warranty to all items installed as standard as a part of the ambulanceconversion. Examplesof items included in this section are the following: • StandardHeat AC units LED Lighting •Inverter/chargers Suction units Leader Industries extends no warranty with respect to chassis electrical systems or components,any electrical components or equipment provided bythe chassis manufacturer,or to any components or equipment manufactured by others and installedby LI,as optional equipment or selected by the purchaser. These Itemsare the subject of warranties issuedby other parties.LI will assist each owner inprocessingany claims under suchother warranties. Normal maintenance items such as light bulbs are not warranted. Examplesof items included in this section are the following: • Radios Intercom Systems Electric02 • Compressors Back up cameras Cot Lifts This warranty is conditioned upon I) normal use and reasonable maintenance of such vehicle and covered attachments as recommended by LI,2) promptwritten noticeof all defectsto LI or itsthen authorized dealerinthe ownersarea,and 3) all repairs,modifications,and additions there to being performed by LI or a party authorized by it..This warranty does not extend to, and will not cover, defects or conditions resulting from misuse,negligence,accident,or overloading beyond applicable ratings. Upon the failure to satisfy any such conditions, this warranty shall become void and unenforceable. Should repairs become necessary undertermsof this warranty,theextentofthe repair shall be determined solely by LI and shall be performed solely by LI or a repair facility designated by LI.Prior approval by Leader Industries isrequiredon all warranty claims.The expense of any transportation to or from such repair facility shall be for the account of the owner and is not covered by this warranty. Leader Industries reserves the unrestricted rightat anytime and from time to time to make changes in the design of, and/or improvements on, its products without thereby imposing anyobligationon itselfto make corresponding changes or improvements in or on its products theretofore manufactured. LEADER INDUSTRIES 10941 Weaver Ave.,South El Monte,CA 91733 14-177 LEADER INDUSTRIES PREMIUM PAINT WARRANTY Limited 7 YEAR -150,000 MILE Leader Industries hereby warrants to the original purchaser of any Leader Industries vehicle that the paint finish on the modular body will be free of defects in materials or workmanship and will perform according to the paint man ufacturer's tech nical s pecifications f or ap eriod of Seven years or 15 0,000 miles, whichever occurs first,subject to the terms and conditions below. This warranty is a full coverage warranty with no prorated items.All warranty coverage must be handled and authorized by Leader Industries,through its distributor network.During the warranty period,Leader Industries will repair any defect covered by this warranty. This warranty is subject to 1)normal use and reasonable maintenance of such modular body and other attachments as recom mended by Le ader Industries 2)p rompt written noti ce of a II d efects to L eader Industries or its th en au thorized distributor in the owne r's a rea prio r to th e expira tion of th e warranty period and 3)all repairs,modifications,and additions thereto being performed by Leader Industries or a party authorized by Leader Industries.This warranty does not extend to,and will not cover defects or conditions resulting from misuse,negligence,accident;or chips,scratches and gloss reduction due to normal use and wear.It will not cover chassis paint that is applied by the chassis manufacturer or paint applied to specific accessories by the manufacturer of said accessory.The failure to satisfy any such condition shall make this warranty void and unenforceable. Should re pairs become necessary under th e te rms of t his warranty,t he extent of th erepair s hall be determined solely by Leader Industries or a rep air facility designated by Leader Industries.The expense of any transportation to and from such facility shall be the obligation of the owner and is not covered by this warranty.Leader Industries shall have no obligation to provide a replacement vehicle while repairs are being made. Leader Industries reserves the right at any time and from time to time to make changes in design of, and/or im provements on its prod ucts without t hereby imp osing an yobi igation on itself to mak e corresponding changes or improvements in or on its products theretofore manufactured. Leader Industries 10941 Weaver Ave.,South El Monte,CA 91733 14-178 FOP-T ATTACHMENT:SERVICE WORKSHEET Service will be a major factor inthe award of this Project.Convenience and experience will be determining factors in defining acceptable service. (1)Manufacturer m ust m aintain a c orporate s erviceand r emount f acility t hat includesa full parts inventory in the State of California.Next business morning delivery to the City shall be available for all parts orders received by 3:00 pm Pacific Standard Time. In order to evaluate the proposed service facilities the following information shall be provided on the appropriate lines. (2) Aservice facility within a radius of50 miles is required. The manufacturer shall train and provide certification to the personnel performing the service with emphasis in the area of electrical service. (3) The manufacturer shall provide claim forms to the warranty repairs and be compensated for their time. 2 ity so that they may m ake FULL CAPABILITIES CORPORATE SERVICE CENTER Miles from City of Newport Beach (should be less than 50 miles) 40 Miles Facility Name Leader Industries Address 10941 Weaver Avenue City,State South El Monte,CA 91733 Contact Doug McEachern Phone (626)459-5150 CAPABILITIES OF FULL CAPABILITIES CORPORATE SERVICE CENTER (CIRCLE ONE) Stocking of c omplete ambulance parts ©N Full-time s ervice r epair personnel O N 14-179 ^p%. ^ipo^ ATTACHMENT:SERVICE WORKSHEET Electrical repair ©N Cabinet repair w N Paint and body repair 0 N Is s ervice c enter owned/operated by t he manufacturer? ©N MANUFACTURER-TRAINED SERVICE FACILITY Located in California?©N Miles from City of Newport Beach:400 N Facility Name FALCKA/ERIHEALTH CA N Address 2190 South McDowell Blvd N City,State Petaluma,CA.94954 N Contact Brad Parson N Phone (707)790-8940 N CAPABILITIES OF MANUFACTURER-TRAINED SERVICE FACILITY (CIRCLE ONE) Stocking of c omplete ambulance parts ©N Full-time s ervice r epair personnel ©N Electrical repair 00 N Cabinet repair ©N Paint and body repair ©N 14-180 EXHIBIT D 1.INSURANCE REQUIREMENTS-VENDORS 1.1 Provision of Insurance.Without limiting Vendor's indemnification of City, and prior to commencement of work, Vendor shall obtain, provide and maintain at its own expense during the term of this Agreement,policies of insurance of the type and amounts described below and in a form satisfactory to City.Contractor agrees to provide insurance in accordance with requirements set forth here.If Contractor uses existing coverage to comply and that coverage does not meet these requirements, Contractor agrees to amend,supplement or endorse the existing coverage. 1.2 Acceptable Insurers.All insurance policies shall be issued by an insurance company currently authorized by the Insurance Commissioner to transact business of insurance in the State of California,with an assigned policyholders'Rating of A-(or higher) and Financial Size Category Class VII (or larger) in accordance withthe latest edition of Best's Key Rating Guide,unless otherwise approved by the City's Risk Manager. 1.3 Coverage Requirements. 1.3.1 Workers'Compensation Insurance.Vendor shall maintain Workers'Compensation Insurance,statutory limits,and Employer's Liability Insurance with limits of at least one million dollars ($1,000,000)each accident for bodily injury by accident and each employee for bodily injury by disease in accordance with the laws of the State of California,Section 3700 of the Labor Code. 1.3.1.1 Vendor shall submit to City,along with the certificate of insurance,a Waiver of Subrogation endorsement in favor of City, its officers,agents, employees and volunteers. 1.3.2 General Liability Insurance.Vendor shall maintain commercial general liability insurance,and if necessary umbrella liability insurance,with coverage at least as broad as provided by Insurance Services Office form CG 00 01, in an amount not less than one million dollars ($1,000,000)per occurrence,two million dollars ($2,000,000)general aggregate.The policy shall cover liability arising from premises, operations,products-completed operations,personal and advertising injury,and liability assumed under an insured contract (including the tort liability of another assumed in a business contract)with no endorsement or modification limiting the scope of coverage for liability assumed under a contract. 1.3.3 Automobile Liability Insurance.Vendor shall maintain automobile insurance at least as broad as Insurance Services Office form CA 00 01 covering bodily injury and property damage for all activities of the Vendor arising out of or in connection with Work to be performed under this Agreement,including coverage for any owned, hired,non-owned or rented vehicles,in an amount not less than one million dollars ($1,000,000)combined single limit each accident. 1.4 Other Insurance Requirements.The policies are to contain,or be endorsed to contain,the following provisions: Halcore Group,Inc., DBA Leader Industries Page D-1 14-181 1.4.1 Waiver of Subrogation.All insurance coverage maintained or procured pursuant to this agreement shall be endorsed to waive subrogation against City,its elected or appointed officers,agents,officials,employees and volunteers or shall specifically allow Vendor or others providing insurance evidence in compliance with these requirements to waive their right of recovery prior to a loss.Vendor hereby waives its own right of recovery against City,and shall require similar written express waivers from each of its subcontractors. 1.4.2 Additional Insured Status.All liability policies including general liability,excess liability,pollution liability,and automobile liability,but not including professional liability,shall provide or be endorsed to provide that City and its officers, officials,employees,and agents shall be included as insureds under such policies. 1.4.3 Primary and Non Contributory.All liability coverage shall apply on a primary basis and shall not require contribution from any insurance or self-insurance maintained by City. 1.4.4 Notice of Cancellation.All policies shall provide City with thirty (30) days'notice of cancellation (except for nonpayment for which ten (10)days'notice is required)or nonrenewal of coverage for each required coverage. 1.5 Additional Agreements Between the Parties.The Parties hereby agree to the following: 1.5.1 Evidence of Insurance.Vendor shall provide certificates of insurance to City as evidence of the insurance coverage required herein,along with a waiver of subrogation endorsement for workers'compensation and other endorsements as specified herein for each coverage.Insurance certificates and endorsement must be approved by City's Risk Manager prior to commencement of performance.Current certification of insurance shall be kept on file with City at all times during the term of this contract.City reserves the right to require complete,certified copies of all required insurance policies,at any time. 1.5.2 City's Right to Revise Requirements.The City reserves the right at any time during the term of the contract to change the amounts and types of insurance required by giving the Vendor sixty (60)days advance written notice of such change.If such change results in substantial additional cost to the Vendor,the City and Vendor may renegotiate Contractor's compensation. 1.5.3 Enforcement of Contract Provisions.Vendor acknowledges and agrees that any actual or alleged failure on the part of the Cityto inform Vendor of non compliance with any requirement imposes no additional obligations on the City nor does it waive any rights hereunder. 1.5.4 Requirements not Limiting.Requirements of specific coverage features or limits contained in this Section are not intended as a limitation on coverage, limits or other requirements,or a waiver of any coverage normally provided by any insurance.Specific reference to a given coverage feature is for purposes of clarification only as it pertains to a given issue and is not intended by any Party or insured to be all inclusive,or to the exclusion of other coverage,or a waiver of any type. Halcore Group,Inc., DBA Leader Industries Page D-2 14-182 1.5.5 Self-insured Retentions.Any self-insured retentions must be declared to and approved by City. City reserves the right to require that self-insured retentions be eliminated,lowered,or replaced by a deductible.Self-insurance will not be considered to comply with these requirements unless approved by City. 1.5.6 City Remedies for Non Compliance If Vendor or any subvendor fails to provide and maintain insurance as required herein,then City shall have the right but not the obligation,to purchase such insurance,to terminate this agreement,or to suspend Vendor's right to proceed until proper evidence of insurance is provided.Any amounts paid by City shall,at City's sole option,be deducted from amounts payable to Vendor or reimbursed by Vendor upon demand. 1.5.7 Timely Notice of Claims.Vendor shall give City prompt and timely notice of claims made or suits instituted that arise out of or result from Vendor's performance under this Agreement,and that involve or may involve coverage under any of the required liability policies. 1.5.8 Vendor's Insurance.Vendor shall also procure and maintain,at its own cost and expense,any additional kinds of insurance,which in its own judgment may be necessary for its proper protection and prosecution of the Work. Halcore Group,Inc., DBA Leader Industries Page D-3 14-183 EXHIBIT E CITY OF NEWPORT BEACH BOND NO. FAITHFUL PERFORMANCE BOND The premium charges on this Bond is $, being at the rate of $thousand of the Contract price. WHEREAS,the City of Newport Beach,State of California,has awarded to Pierce Manufacturing,Inc.hereinafter designated as the "Principal,"a contract for the manufacturing of One (1)100'tractor-drawn aerial ladder with pump in strict conformity with the Contract on file with the office of the City Clerk of the City of Newport Beach, which is incorporated herein by this reference. WHEREAS,Principal has executed or is about to execute the Contract and the terms thereof require the furnishing of a Bond for the faithful performance of the Contract. NOW,THEREFORE,we,the Principal,and ,duly authorized to transact business under the laws of the State of California as Surety (hereinafter "Surety"),are held and firmly bound unto the City of Newport Beach,in the sum of Dollars and /100 ($) lawful money of the United States of America,said sum being equal to 100%of the estimated amount of the Contract,to be paid to the City of Newport Beach,its successors,and assigns;for which payment well and truly to be made,we bind ourselves, our heirs,executors and administrators,successors,or assigns,jointly and severally, firmly by these present. THE CONDITION OF THIS OBLIGATION IS SUCH,that if the Principal,or the Principal's heirs,executors,administrators,successors,or assigns,fail to abide by,and well and truly keep and perform any or all the work,covenants,conditions,and agreements in the Contract Documents and any alteration thereof made as therein provided on its part,to be kept and performed at the time and in the manner therein specified,and in all respects according to its true intent and meaning,or fails to indemnify, defend,and save harmless the City of Newport Beach,its officers,employees and agents, as therein stipulated,then,Surety will faithfully perform the same,in an amount not exceeding the sum specified in this Bond;otherwise this obligation shall become null and void. As a part of the obligation secured hereby,and in addition to the face amount specified in this Performance Bond,there shall be included costs and reasonable expenses and fees,including reasonable attorney's fees,incurred by the City,only in the event the City is required to bring an action in law or equity against Surety to enforce the obligations of this Bond. Surety,for value received,stipulates and agrees that no change,extension of time, alterations or additions to the terms of the Contract or to the work to be performed Halcore Group,Inc., DBA Leader Industries Page E-1 14-184 thereunder shall in any way affect its obligations on this Bond,and it does hereby waive notice of any such change,extension of time,alterations or additions of the Contract or to the work or to the specifications. This Faithful Performance Bond shall be extended and maintained by the Principal in full force and effect for one (1)year following the date of formal acceptance of the Equipment by the City. In the event that the Principal executed this bond as an individual,it is agreed that the death of any such Principal shall not exonerate the Surety from its obligations under this Bond. IN WITNESS WHEREOF,this instrument has been duly executed by the Principal and Surety above named,on the day of ,2016. Name of Contractor (Principal)Authorized Signature/Title Name of Surety Authorized Agent Signature Address of Surety Print Name and Title Telephone NOTARY ACKNOWLEDGMENTS OF CONTRACTOR AND SURETY MUST BE ATTACHED Halcore Group,Inc.,DBA Leader Industries Page E-2 14-185 ACKNOWLEDGMENT A notary public or other officer completing this certificate verifies only the identity of the individual who signed the document to which this certificate is attached,and not the truthfulness,accuracy,or validity of that document. State of California County of }ss. On , 20 before me, Notary Public,personally appeared who proved to me on the basis of satisfactory evidence to be the person(s)whose name(s) is/are subscribed to the within instrument and acknowledged to me that he/she/they executed the same in his/her/their authorized capacity(ies),and that by his/her/their signatures(s)on the instrument the person(s),or the entity upon behalf of which the person(s)acted,executed the instrument. I certify under PENALTY OF PERJURY under the laws of the State of California that the foregoing paragraph is true and correct. WITNESS my hand and official seal. Signature (seal) ACKNOWLEDGMENT A notary public or other officer completing this certificate verifies only the identity of the individual who signed the document to which this certificate is attached,and not the truthfulness,accuracy,or validity of that document. State of California County of }ss. On , 20 before me, Notary Public,personally appeared proved to me on the basis of satisfactory evidence to be the person(s)whose name(s)is/are subscribed to the within instrument and acknowledged to me that he/she/they executed the same in his/her/their authorized capacity(ies),and that by his/her/their signatures(s)on the instrument the person(s),or the entity upon behalf of which the person(s)acted,executed the instrument. I certify under PENALTY OF PERJURY under the laws of the State of California that the foregoing paragraph is true and correct. WITNESS my hand and official seal. Signature (seal) Halcore Group,Inc.,DBA Leader Industries Page E-3 14-186 ATTACHMENT B 14-187