HomeMy WebLinkAbout01 - 09_RTC Part 91111491
AOL
As a consequence of its function, the stormwater conveyance system collects and transports
urban runoff and storm water that may contain certain pollutants. Consequently these pollutants
may accumulate in the system and must be removed periodically. In addition, the systems must
also be maintained to function properly hydraulically to avoid flooding. Maintaining the system
may involve the following activities:
1. Inspection and Cleaning of Stormwater Conveyance Structures
2. Controlling Illicit Connections and Discharges
3. Controlling Illegal Dumping
This list of Model Maintenance Procedures can be utilized as an inspection checklist to determine
where better compliance with Designated Minimum Best Management Practices (notated with
checkmarks and capital letters) is needed, and to recommend Additional Best Management
Practices (notated with bullet points and lower case letters) that may be applicable under certain
circumstances, especially where there are certain Pollutant Constituents of Concern. BMPs
applicable to certain constituents are notated as:
Bacteria (BACT) Sediment (SED) Nutrients (NUT) Oil and Grease (0 &G) Pesticides (PEST)
OtherToxic Compounds (TOX) Trash (TRASH) Hydrological Impacts (HYD) Any /AII or General (ANY)
Program /Facility Being Inspected:
Date:
Inspector Name:
When completed, the checklist should be attached to the General Inspection Form Cover Sheet
and copies should be provided to the Supervisor of the Facility /Program being inspected.
MAINTENANCE PROCEDURES:
Inspection and Cleaning of Drainage Facilities
OK
❑ ❑
❑ ❑
❑ ❑
❑ ❑
T 1A. Annually inspect and clean drainage structures as
needed.
T 1 B. Maintain appropriate records of cleaning and
inspections.
T 1C. Properly dispose of removed materials at a landfill
or recycling facility.
T 1D. Conduct intermittent supplemental visual
inspections during the wet season to determine if there are
problem inlets where sediment/trash or other pollutants
accumulate, and provide for additional cleanouts as
appropriate.
T 1E. Prevent or clean up any discharges that may occur
during the course of maintenance and cleaning
procedures.
T IF. Verify that appropriate employees or subcontractors
are trained in proper conductance of maintenance
activities, including record keeping and disposal.
T 1G. Annually inspect and clean v- ditches as needed,
prior to the wet season. On shrub - covered slopes,
vegetative debris may be placed on the downhill side of
the ditch. Trash should be bagged and disposed at a
landfill
County of Orange 02/13/03 Page 1 of 4
®F -1
Unsatisfactory
ppt
❑ ❑
General Guidelines (cont.)
o 1a. Remove trash or debris as needed from open
channels. It should be noted that major vegetative debris
removal may require other regulatory permits prior to
completing the work. (TRASH)
0 1 b. Consider retrofitting energy dissipaters (e.g. riprap)
below culvert outfalls to minimize potential for erosion.
(SED)
0 1c. Repair any v- ditches that have cracked or displaced
in a manner that accelerates erosion. (SED)
• 1d. If suspicious conditions appear to exist, test selected
samples of the removed wastes for compliance with
hazardous waste regulations prior to disposal. (TOX)
• 1e. Consider more frequent regular cleaning of selected
drainage structures to help address ongoing specific
impairments. (SED, BACT, NUT, TRASH)
• 1f. Consider structural retrofits to the MS4 to help
address ongoing specific impairments (SED, BACT, NUT,
TRASH, O &G)
• 1g. Consider cleaning out pipes at gradient breaks or
other in -pipe debris accumulation points as
identified /needed. (ANY, BACT, NUT, TRASH)
Storm Drain Flushing
0 1 h. Flushing of storm drains or storm drain inlets should
only be done when critically necessary and no other
solution is practical. (SED, BACT, TRASH).
0 1 i. If flushed, to the extent practical the material should
be collected (vacuumed), treated with an appropriate
filtering device to remove sand and debris and disposed
of properly. (SED)
Waste Management
T 1 H. Store wastes collected from cleaning activities of the
drainage facilities in appropriate containers or temporary
storage sites in a manner that prevents discharge to the
storm drain.
0 1j. Dewater the wastes if necessary with outflow into the
sanitary sewer if permitted. Water should be treated with
an appropriate filtering device to remove the sand and
debris prior to discharge to the sanitary sewer. If
discharge to the sanitary sewer is not permitted, water
should be pumped or vacuumed to a tank and properly
disposed of. Do not dewater near a storm drain or
stream. (SED, TRASH)
0 1k. Provide for laboratory analysis of at least one
randomly collected sediment (less the debris) sample per
year from the storm drain inlet leaning program to ensure
that it does not meet the EPA criteria for hazardous
waste. If the sample is determined to be hazardous, the
sediment must be disposed of as hazardous waste and
the source should be investigated. (TOX).
❑ ❑
❑ ❑
❑ ❑
❑ ❑
❑ ❑
❑ ❑
Q ❑
❑ ❑
❑ ❑
❑ ❑
❑ ❑
County of Orange 02/13103 Page 2 of 4
®F-1
2. Controlling Illicit Connections and Discharges
❑ ❑
T 2A. Report prohibited discharges such as dumping, paint
spills, abandoned oil containers, etc. observed during the
course of normal daily activities so they can be
investigated, contained, and cleaned up.
T 2B. Where field observations and /or monitoring data
indicate significant problems, conduct field investigations to
detect and eliminate existing illicit connections and
improper disposal of pollutants into the storm drain (i.e.
identify problem areas where discharges or illegal
connections may occur and follow up stream to determine
the source(s)). (Refer to Appendices A -10 and M 1.)
T 2C. Report all observed illicit connections and
discharges to the 24 -hour water pollution problem reporting
hotline (714) 567 -6363.
T 2D. Encourage public reporting of improper waste
disposal by distributing public education materials and
advertising the 24-hour water pollution problem reporting
hotline.
Storm Drain Stenciling ( "No Dumping— Drains to Ocean ")
T 2E. Implement and maintain a storm drain stenciling
program.
= 2a. Consider adding the hotline number to the storm
drain stencils (BACT, TOX, TRASH).
❑ ❑
❑ ❑
❑ ❑
❑ ❑
❑ ❑
3. Controlling Illegal Dumping
❑ ❑
Field Investigation
T 3A. Report prohibited discharges such as dumpings
observed during the course of normal daily activities so
they can be investigated, contained and cleaned up.
T 3B. Conduct field investigations to detect and eliminate
improper disposal of pollutants into the storm drain (i.e.
identify problem areas where discharges or illegal
connections may occur and follow up stream to determine
the source(s)).
T 3C. Report all observed illegal dumping to the 24 -hour
water pollution problem reporting hotline (714) 567 -6363.
T 3D. Encourage public reporting of improper waste
disposal by distributing public education materials and
advertising the 24 -hour water pollution problem reporting
hotline.
T 3E. If perpetrator can be identified, take appropriate
enforcement action.
a 3a. Consider posting "No Dumping" signs in problem
areas with a phone number for reporting dumping and
disposal. Signs could also indicate fines and penalties for
illegal dumping. (ANY)
❑ ❑
❑ ❑
❑ ❑
❑
❑ ❑
County of Orange 02/13/03 Page 3 of 4
Unsatisfactory OKI T
❑ ❑
LIMITATIONS:
®E -1
3F. Verify that appropriate employees and
subcontractors are trained to recognize and report illegal
dumping.
3G. Encourage public reporting of illegal dumping by
advertising the 24 -hour water pollution problem reporting
hotline (714) 567 -6363.
3b. Take extra steps to educate the public in
neighborhoods where illegal dumping has occurred to
inform them why illegal dumping is a problem, and that
illegal dumping carries a significant financial penalty.
(ANY)
Clean -up activities may create a slight disturbance for local aquatic species. Access to items
and material on private property may be limited. Trade -offs may exist between channel
hydraulics and water quality /riparian habitat. If storm channels or basins are recognized as
wetlands, many activities, including maintenance, may be subject to regulation and permitting.
County of Orange 02/13/03 Page 4 of 4
-----7
R -1
AUTOMOBILE REPAIR AND
MAINTENANCE
Automobile repair and maintenance activities have the potential to
contribute directly to storm drain systems primarily through spills or
the dumping of waste fluids being conveyed to the storm drain.
Automotive fluids, such as oils, greases, and solvents, are
hydrocarbon based, and may contain metals, chlorinated
hydrocarbons, and other toxic compounds. Removal of caked dirt
and grime from an automobile increases the sediment load to the
storm drain system. The pollution prevention activities outlined in
this fact sheets are used to prevent the discharge of pollutants to the
storm drain system.
Think before conducting automobile repair and maintenance
activities. Remember - The ocean starts at your front door.
The activities outlined in this fact
sheet target the following
pollutants:
Sediment
x
Nutrients
Bacteria
Foaming A ents
Metals
x
Hydrocarbons
x
Hazardous Materials
x
Pesticides and
Herbicides
Other
Required Activities
• Recycle used oil and antifreeze by taking them to service stations and other
recycling centers. Never pour oil in storm drains or other areas.
• Do not perform repair and maintenance activities during rain events.
RECYCLE
• Immediately clean up and contain any spills. Dispose of all waste and adsorbent U s E D 0 t L
materials properly.
• Store hazardous materials and wastes (including, but not limited to, fluids, solvents,
parts containing fluids, batteries) indoors, under cover, or in watertight containers.
• Perform automobile maintenance and repairs over impervious surfaces such as concrete,
so spills and waste material should be readily cleaned up. Use drip pans, plastic
sheeting, etc. to contain spills and waste material.
• Dispose of cleaning solvents at the designated hazardous waste center.
Recommended Activities
• Conduct auto repair activities at a commercial repair facility
• Perform automobile repair and maintenance activities under a covered area.
• Do not buy fluids containing target pollutants (e.g. degreasers containing PERC).
• Monitor parked or stored vehicles and equipment for leaks and place pans under leaks
to collect fluids for proper disposal or recycling.
For additional Information contact:
County of Orange, OC Watershed
Main: (714) 955 -0600 Water Pollution Discharge Hotline 1- 877 -89 -SPILL
or visit our website at: www.ocwatersheds.com
NA%
Automobile waslung activities have the potential to contribute
pollutants because road dust washed from vehicles may contain
metals and hydrocarbons. Any leaking fluids washed from the
automobile may be carried to the storm drain by the wash water.
Detergents used for automobile washing may also contain
phosphorus and foaming agents, which contribute to the
eutrophication of receiving waterbodies. The pollution prevention
activities outlined in this fact sheets are used to prevent the discharge
of pollutants to the storm drain system.
The activities outlined in this fad
sheet target the following
pollutants:
Sediment
x
Nutrients
X
Bacteria
Foamin,Q Agents
X
Metals
X
Hydrocarbons
X
Hazardous Materials
x
Pesticides and
Herbicides
Other
Think before conducting automobile washing activities. Remember - The ocean starts at your
front door.
Required Activities
• Shake floor mats into trashcan or vacuum to clean. Do not shake over ground.
• If using cleaners (such as acid based wheel cleaners) use a rag to wipe them on and off,
do not rinse them off with water.
If possible, divert runoff from automobile washing to a grassy surface large enough to
contain and allow complete infiltration
• Dispose of excess wash water into the sanitary sewer (i.e. via sink, or toilet) or onto a
landscaped area that will allow for complete infiltration.
• Conduct engine degreasing at a commercial facility that is setup to handle that type of
waste.
Recommended Activities
• When possible, use commercial wash facili ties
• Wash velcles over pervious surfaces such as lawns and gravel areas
• Choose soaps, cleaners, or detergents labeled "non - toxic ", "phosphate free ", or
"biodegradable ". Vegetable and citrus- based products are typically safest for the
environment.
• Turn off water when not actively washing down automobile.
• If available, use established neighborhood wash areas, where runoff is properly
controlled and managed.
For additional information contact:
County of Orange, OC Watershed
Main: (714) 955- 0600124hr Water Pollution Discharge Hotline 1- 877 -89 -SPILL
or visit our website at: www.ocwatersheds.com
R -3
AUTOMOBILE PARKING
Parked automobiles may contribute pollutants to the storm
drain because poorly maintained vehicles may leak fluids
containing hydrocarbons, metals, and other pollutants. In
addition, heavily soiled automobiles may drop clods of dirt
onto the parking surface, contributing to the sediment load
when runoff is present During rain events, or wash -down
activities, the pollutants may be carried into the storm drain
system. The pollution prevention activities outlined in this
fact sheets are used to prevent the discharge of pollutants to
the storm drain system.
The activities outlined in this fact
sheet target the following
pollutants:
Sediment
x
Nutrients
Bacteria
Foaming Agents
Metals
X
Hydrocarbons
X
Hazardous Materials
z
Pesticides and
Herbicides
Other
Think before parking your car. Remember - The ocean starts at your front door.
Required Activities
• If required, vehicles have to be removed from the street during designated street
sweeping /cleaning times.
• If the automobile is leaking, place a pan or similar collection device under the
automobile, until such time as the leak may be repaired.
• Use dry cleaning methods to remove any materials deposited by vehicles (e.g.
adsorbents for fluid leaks, sweeping for soil clod deposits).
Recommended Activities
• Park automobiles over permeable surfaces (e.g. gravel, or porous cement).
• Limit vehicle parking to covered areas.
• Perform routine maintenance to minimize fluid leaks, and maximize fuel
efficiency.
For additional information contact:
County of Orange, OC Watershed
Main: (714) 955 - 0600 / 24hr Water Pollution Discharge Hotline 1- 877 -89 -SPILL
or visit our website al: www.ocwatersheds.com
HOME CARE
R -4
LIN 0 V1 04 *1
Many hazardous materials may be used in and around
residences during routine maintenance activities (such as: oils,
paints, cleaners, bleaches, pesticides, glues, solvents, and other
products). Improper or excessive use of these products can
increase the potential for pollutants to be transported to the
storm drain by runoff. The pollution prevention activities
outlined in this fact sheets are used to prevent the discharge of
pollutants to the storm drain system.
Think before conducting home care activities. Remember - The
ocean starts at your front door.
Required Activities
The activities outlined in this fact
sheet target the following
pollutants:
Sediment
x
Nutrients
Bacteria
x
Foaming Agents
x
Metals
x
Hydrocarbons
x
Hazardous Materials
x
Pesticides and
Herbicides
Other
IF
• Clean out painting equipment in an area where the waste can be contained and properly
disposed of (latex - sewer, oil based - household hazardous waste center).
• Rinse off cement mixers and cement laden tools in a contained washout area. Dispose
of dried concrete waste in household trash.
• If safe, contain, clean up, and properly dispose all household hazardous waste spills. If
an unsafe condition exists, call 911 to activate the proper response learn.
• Household hazardous materials must be stored indoors or under cover, and in closed
and labeled containers. Dispose of them at a household hazardous waste center.
• Household wash waters (e.g. washer machine effluent, mop water, etc.) must be
disposed of in the sanitary sewer.
• Pool and spa water may be discharged to the storm drain if residual chlorine is less than
0.1 mg /L, the pH is between 6.5 and 8.5, and the water is free from any unusual
coloration. (Call 714 -834 -6107 to obtain information on a pool drain permit). Pool filter
media must be contained and disposed of properly.
Recommended Activities
Only purchase the types and amounts of materials needed.
Share unused portions of products with neighbors or community programs (latex paint)
For additional information contact:
County of Orange, OC Watershed
Main: (714) 955.0600/ 24hr Water Pollution Discharge Hotline 1- 877 -89 -SPILL
or visit our website at: www.ocwalersheds.com
GARDEN CARE
Garden activities may contribute pollutants via soil erosion,
green waste, fertilizer and pesticide use. Plant and garden
care activities such as landscape maintenance, fertilization,
and pesticide application have the potential to discharge
significant quantities of pollutants to the storm drain system.
Nonvegetated surfaces may allow for significant erosion
leading to high sediment loads. Other pollutants such as
pesticides may adsorb onto the soil particles and be
transported off site. Excess fertilizer and pesticide pollutants
from over application may be carried to the storm drain by
dissolving in irrigation runoff or rainwater. Green wastes
may also contain organic matter and may have adsorbed
fertilizers and pesticides.
The activities outlined in this fact
sheet target the following
pollutants:
Sediment
x
Nutdents
x
Bacteria
x
Foaming Agents
Metals
Hydrocarbons
Hazardous Materials
Pesticides and
Herbicides
x
Other
x
Excessive irrigation is often the most significant factor in home and garden care activities.
Pollutants may dissolve in irrigation water and then be transported to the storm drain, or
particles and materials coated with fertilizers and pesticides may be suspended in the irrigation
flow and carried to the storm drain. The pollution prevention activities outlined in this fact
sheets are used to prevent the discharge of pollutants to the storm drain system.
Think before conducting garden care activities. Remember - The ocean starts at your front door.
Required Activities
• Irrigation systems must be properly adjusted to reflect seasonal water needs.
• Minimize the use of pesticides and fertilizers. Read the labels and follow directions to
avoid improper use. Do not apply chemicals if it is windy or about to rain.
• Properly clean up and dispose of spills of gardening chemicals, fertilizes, or soils. If
possible, return the spilled material to the container for future use.
• Lawn and garden care products must be stored in closed labeled containers, in covered
areas, or off - ground and under protective tarps.
• Household hazardous waste must be properly disposed at a household hazardous waste
center.
• Cover nonvegetated surfaces to prevent erosion.
Recommended Activities
• Utilize xeroscaping and use of drought and insect resistant landscaping.
• Cultivate garden often to control weeds
e Use integrated pest management (IPM). Planting pest repelling plants (e.g. Marigolds)
or using pest eating insects (e.g. ladybugs) may reduce the need for pesticides.
• Do not leave food (human or pet) outside overnight
• Remove fruit and garden waste
For additional information contact:
County of Orange, OC Watershed
Main: (714) 955-0600/ 24hr Water Pollution Discharge Hotline 1- 877 -89 -SPILL
or visit our website at: www.ocwatersheds.com
Pet wastes left in the environment may introduce solids,
bacteria, and nutrients to the storm drain. The type and
quantity of waste will dictate the proper disposal
method. Small quantities of waste are best disposed
with regular trash or flushed down a toilet. Large
quantities of wastes from herbivore animals may be
composted for subsequent use or disposal to landfill.
Pickup after your pet' It's as easy as 1 -2 -3. 1) Bring a
bag. 2) Clean it up. 3) Dispose of it properly (toilet or
trash). The pollution prevention activities outlined in
this fact sheets are used to prevent the discharge of
pollutants to the storm drain system.
The activities outlined in this fact
sheet target the following
pollutants:
Sediment
x
Nutrients
x
Bacteria
x
Foaming
Agents
Metals
Hydrocarbons
Hazardous Materials
Pesticides and
Herbicides
Other
Think before you dispose of any pet wastes. Remember - The ocean starts at your front
door.
Required Activities
All pet wastes must be picked up and properly disposed of. Pet waste should be
disposed of in the regular trash, flushed down a toilet, or composted as type and
quantities dictate.
C Properly dispose of unused flea control products (shampoo, sprays, or collars).
Manure produced by livestock in uncovered areas should be removed at least
daily for composting, or storage in water -tight container prior to disposal. Never
hose down to stream or storm drain. Composting or storage areas should be
configured and maintained so as not to allow contact with runoff. Compost may
be donated to greenhouses, nurseries, and botanical parks. Topsoil companies
and composting centers may also accept composted manure.
a Line waste pits or trenches with an impermeable layer, such as duck plastic
sheeting.
When possible, allow wash water to infiltrate into the ground, or collect in an
area that is routed to the sanitary sewer.
9 Confine livestock in fenced in areas except during exercise and grazing times.
Restrict animal access to creeks and streams, preferably by fencing.
For additional information contact:
County of Orange, OC Watershed
Main: (714) 955 - 0600 / 24hr Water Pollution Discharge Hotline 1- 877 -89 -SPILL
or visit our website at: www.ocwatersheds.com
• Install gutters that will divert roof runoff away from livestock areas.
Recommended Activities
• In order to properly dispose of pet waste, carry bags, pooper - scooper, or
equivalent to safely pick up pet wastes while walking with pets.
• Bathe pets indoors and use less toxic shampoos. When possible, have pets
professionally groomed.
• Properly inoculate your pet in order to maintain their health and reduce the
possibility of pathogens in pet wastes.
• Maintain healthy and vigorous pastures with at least three inches of leafy
material.
• Consider indoor feeding of livestock during heavy rainfall, to minimize manure
exposed to potential runoff.
• Locate barns, corrals, and other high use areas on portions of property that either
drain away from or are located distant form nearby creeks or storm drains.
For additional information contact:
County of Orange, OC Watershed
Main: (714) 955 - 0600 / 24hr Water Pollution Discharge Hotline 1- 877 -89 -SPILL
or visit our wehsite at: www.ocwatersheds.com
R -6
DISPOSAL OF GREEN WASTES
Green wastes entering the storm drain may clog the
system creating flooding problems. Green wastes washed
into receiving waters create an oxygen demand as they are
decomposed, reducing the available oxygen for aquatic
life. Pesticide and nutrient residues may be carried to the
receiving water with the green wastes. The pollution
prevention activities outlined in this fact sheets are used to
prevent the discharge of pollutants to the storm drain
system.
The activities outlined in this fact
sheet target the following
pollutants:
Sediment
x
Nutrients
x
Bacteria
x
Foaming Agents
Metals
Hydrocarbons
Hazardous Materials
x
Pesticides and
Herbicides
x
Other
Think before disposing of any green wastes - Remember - The ocean starts at your front
door.
Required Activities
• Green wastes can not be disposed of in the street, gutter, public right -of -way,
storm drain, or receiving water. Dispose of green wastes as a part of the
household trash. If the quantities are too large, arrange a pick up with the local
waste hauler.
• After conducting yard or garden activities sweep the area and properly dispose of
the clippings and waste. Do not sweep or blow out into the street or gutter.
Recommended Activities
• Utilize a commercial landscape company to conduct the landscape activities and
waste disposal.
• Utilize native plants and drought tolerant species to reduce the water use and
green waste produced.
• Use a lawn mower that has a mulcher so that the grass clippings remain on the
lawn and do not have to be collected and disposed of
• Compost materials in a designated area within the yard.
• Recycle lawn clippings and greenery waste through local programs if available.
For additional information contact:
County of Orange, OC Watershed
Main: (714) 955.0600124hr Water Pollution Discharge Hotline 1. 877 -89 -SPILL
or visit our website at: www.ocwatersheds.com
R -7
HOUSEHOLD HAZARDOUS
WASTE
Jou -
Household hazardous wastes (HHW) are defined as
waste materials which are typically found in homes or
similar sources, which exhibit characteristics such as:
corrosivity, ignitability, reactivity, and /or toxicity, or
are listed as hazardous materials by EPA.
List of most common HHW
products:
Drain openers
Oven cleaners
Wood and metal cleaners and
polishes
Automotive oil and fuel additives
Grease and rust solvents
Carburetor and fuel injection
cleaners
Starter fluids
Batteries
Paint Thinners
Paint strippers and removers
Adhesives
Herbicides
Pesticides
Fungicidestwood preservatives
Required Activities
Many types of waste can be
recycled, however options
for each waste type are
limited. Recycling is always
preferable to disposal of
unwanted materials. All
The activities outlined in this fact
sheet target the following
pollutants:
Sediment
Nutrients
Bacteria
Foaming Agents
x
Metals
x
H drocarbons
x
Hazardous Materials
x
Pesticides and
Herbicides
x
Other
x
gasoline, antifreeze, waste oil, and lead -acid batteries
can be recycled. Latex and oil -based paint can be
reused, as well as recycled. Materials that cannot be
reused or recycled should be disposed of at a properly
permitted landfill. 6
Think before disposing of any household hazardous RECYCLE
waste. Remember - The ocean starts at your front door. U 5 E D O t L
Dispose of HHW at a local collection facility. Call (714) 834 -6752 for the
household hazardous waste center closest to your area.
Household hazardous materials must be stored indoors or under cover, and in
closed and labeled containers.
• If safe, contain, clean up, and properly dispose all household hazardous waste
spills. If an unsafe condition exists, call 911 to activate the proper response
team.
Recommended Activities
Use non - hazardous or less - hazardous products.
Participate in HHW reuse and recycling. Call (714) 834 -6752 for the
participating household hazardous waste centers.
The California Integrated Waste Management Board has a RecycBng Hothne (809) 553 -2962, that provides intormation and recycling locations for
used al.
For additional information contact:
County of Orange, OC Watershed
Main: (714) 955 -0600/ 24hr Water Pollution Discharge Hotline 1- 877 -89 -SPILL
or visit our website at: www,ocwatersheds.com
R -8
WATER CONSERVATION
Excessive irrigation and /or the overuse of water is often
the most significant factor in transporting pollutants to
the storm drain system. Pollutants from a wide variety of
sources including automobile repair and maintenance,
automobile washing, automobile parking, home and
garden care activities and pet care may dissolve in the
water and be transported to the storm drain. In addition,
particles and materials coated with fertilizers and
pesticides may be suspended in the flow and be
transported to the storm drain.
Hosing off outside areas to wash them down not only
consumes large quantities of water, but also transports any pollutants, sediments, and
waste to the storm drain system. The pollution prevention activities outlined in this fact
sheets are used to prevent the discharge of pollutants to the storm drain system.
The activities outlined in this fact
sheet target the following
ollutants:
Sediment
x
Nutrients
x
Bacteria
x
Foaming Agents
x
Metals
x
Hydrocarbons
x
Hazardous Materials
x
Pesticides and
Herbicides
x
Other
x
Think before using water. Remember - The ocean starts at your front door.
Required Activities
• Irrigation systems must be properly adjusted to reflect seasonal water needs.
• Do not hose off outside surfaces to clean, sweep with a broom instead.
Recommended Activities
• Fix any leaking faucets and eliminate unnecessary water sources.
• Use xeroscaping and drought tolerant landscaping to reduce the watering needs.
• Do not over watering lawns or gardens. Over watering wastes water and
promotes diseases.
• Use a bucket to re -soak sponges/ rags while washing automobiles and other
items outdoors. Use hose only for rinsing.
• Wash automobiles at a commercial car wash employing water recycling.
For additional information contact:
County of Orange. OC Watershed
Main: (714) 955 -0600/ 24hr Water Pollution Discharge Hotline 1- 877 -89 -SPILL
or visit our website at: www.ocwatersheds.com
Site Design & Landscape Planning SD -10
Design Objectives
0
Maximize Infiltration
0
Provide Retention
0
Slow Runoff
Minimize Impervious Land
Coverage
Prohibit Dumping of Improper
Materials
Contain Pollutants
Collect and Convey
Description
Each project site possesses unique topographic, hydrologic, and vegetative features, some of
which are more suitable for development than others. Integrating and incorporating
appropriate landscape planning methodologies into the project design is the most effective
action that can be done to minimize surface and groundwater contamination from stormwater.
Approach
Landscape planning should couple consideration of land suitability for urban uses with
consideration of community goals and projected growth. Project plan designs should conserve
natural areas to the extent possible, maximize natural water storage and infiltration
opportunities, and protect slopes and channels.
Suitable Applications
Appropriate applications include residential, commercial and industrial areas planned for
development or redevelopment.
Design Considerations
Design requirements for site design and landscapes planning
should conform to applicable standards and specifications of
agencies with jurisdiction and be consistent with applicable
General Plan and Local Area Plan policies.
January 2003 California Stormwater BMP Handbook I of 4
New Development and Redevelopment
www.cabmphandbooks.com
SD -10 Site Design & Landscape Planning
Designing New Installations
Begin the development of a plan for the landscape unit with attention to the following general
principles:
■ Formulate the plan on the basis of clearly articulated community goals. Carefully identify
conflicts and choices bet%veen retaining and protecting desired resources and community
growth.
■ Map and assess land suitability for urban uses. Include the following landscape features in
the assessment: wooded land, open mnvooded land, steep slopes, erosion -prone soils,
foundation suitability, soil suitability for waste disposal, aquifers, aquifer recharge areas,
wetlands, floodplains, surface waters, agricultural lands, and various categories of urban
land use. When appropriate, the assessment can highlight outstanding local or regional
resources that the community determines should be protected (e.g., a scenic area,
recreational area, threatened species habitat, farmland, fish run). Mapping and assessment
should recognize not only these resources but also additional areas needed for their
sustenance.
Project plan designs should conserve natural areas to the extent possible, maximize natural
water storage and infiltration opportunities, and protect slopes and channels.
Conserve Natural Areas during Landscape Planning
If applicable, the following items are required and must be implemented in the site layout
during the subdivision design and approval process, consistent with applicable General Plan and
Local Area Plan policies:
■ Cluster development on least- sensitive portions of a site while leaving the remaining land in
a natural undisturbed condition.
■ Limit cleating and grading of native vegetation at a site to the minimum amount needed to
build lots, allow access, and provide fire protection.
■ Maximize trees and other vegetation at each site by planting additional vegetation, clustering
tree areas, and promoting the use of native and /or drought tolerant plants.
■ Promote natural vegetation by using parldng lot islands and other landscaped areas.
■ Preserve riparian areas and wetlands.
Maximize Natural Water Storage and Infritration Opportunities Within the Landscape Unit
■ Promote the conservation of forest cover. Building on lard that is already deforested affects
basin hydrology to a lesser extent than converting forested land. Loss of forest cover reduces
interception storage, detention in the organic forest floor layer, and water losses by
evapotranspiration, resulting in large peak runoff increases and either their negative effects
or the expense of countering them with structural solutions.
■ Maintain natural storage reservoirs and drainage corridors, including depressions, areas of
permeable soils, swales, and internnittent streams. Develop and implement policies and
2 of 4 California Stormwater BMP Handbook January 2003
New Development and Redevelopment
www.cabmphandbooks.com
Site Design & Landscape Planning SD -10
regulations to discourage the clearing, filling, and channelization of these features. Utilize
them in drainage networks in preference to pipes, culverts, and engineered ditches.
Evaluating infiltration opportunities by referring to the stormwater management manual for
the jurisdiction andpay particular attention to the selection criteria for avoiding
groundwater contamination, poor soils, and hydrogeological conditions that cause these
facilities to fail. If necessary, locate developments with large amounts of impervious
surfaces or a potential to produce relatively contaminated runoff away from groundwater
recharge areas.
Protection of Slopes and Channels during Landscape Design
• Convey runoff safely from the tops of slopes.
• Avoid disturbing steep or unstable slopes.
• Avoid disturbing natural channels.
• Stabilize disturbed slopes as quickly as possible.
• Vegetate slopes with native or drought tolerant vegetation.
• Control and treat flows in landscaping and /or other controls prior to reaching existing
natural drainage systems.
• Stabilize temporary and permanent channel crossings as quicldy as possible, and ensure that
increases in ran -off velocity and frequency caused by the project do not erode the channel.
• Install energy dissipaters, such as riprap, at the outlets of new storm drains, culverts,
conduits, or channels that enter unlined channels in accordance with applicable
specifications to minimize erosion. Energy dissipaters shall be installed in such a way as to
minimize impacts to receiving waters.
■ Line on -site conveyance channels where appropriate, to reduce erosion caused by increased
flow velocity due to increases in tributary impervious area. The first choice for linings
should be grass or some other vegetative surface, since these materials not only reduce
runoff velocities, but also provide water quality benefits from filtration and infiltration. If
velocities in the channel are high enough to erode grass or other vegetative linings, riprap,
concrete, soil cement, or geo -grid stabilization are other alternatives.
is Consider other design principles that are comparable and equally effective.
Redeveloping Existing Installations
Various jurisdictional stormnvater management and mitigation plans (SUSMP, WQMP, etc.)
define "redevelopment" in terms of amounts of additional impervious area, increases in gross
floor area and /or exterior construction, and land disturbing activities with structural or
impervious surfaces. The definition of " redevelopment" must be consulted to determine
whether or not the requirements for new development apply to areas intended for
redevelopment_ If the definition applies, the steps outlined under "designing nety installations"
above should be followed.
January 2003 California Stormwater BMP Handbook 3 of 4
New Development and Redevelopment
www.cabmphandbooks.com
SD -10 Site Design & Landscape Planning
Redevelopment may present significant opportunity to add features which had not previously
been implemented. Examples include incorporation of depressions, areas of permeable soils,
and swales in newly redeveloped areas. While some site constraints may exist due to the status
of already existing infrastructure, opportunities should not be missed to maximize infiltration,
slow runoff, reduce impervious areas, disconnect directly connected impervious areas.
Other Resources
A Manual for the Standard Urban Stornnvater Mitigation Plan (SUSMP), Los Angeles County
Department of Public Works, May 2002.
Stormwater Management Manual for Western Washington, Washington State Department of
Ecology, August 2001.
Model Standard Urban Stonn Water Mitigation Plan (SUSMP) for San Diego County, Port of
San Diego, and Cities in San Diego County, February 14, 2002.
Model Water Quality Management Plan (WQMP) for County of Orange, Orange County Flood
Control District, and the Incorporated Cities of Orange County, Draft February 2003.
Ventura Countywide Technical Guidance Manual for Stonnwater Quality Control Measures,
July 2002.
4 of 4 California Stormwater BIdP Handbook January 2003
New Development and Redevelopment
www.cabmphandbooks.com
Roof Runoff Controls
Rain Garden
SD -11
Design Objectives
Q Maximize Infiltration
Q Provide Retention
Q Slow Runoff
Minimize Impervious Land
Coverage
Prohibit Dumping of Improper
Materials
Q Contain Pollutants
Collect and Convey
Description
Various roof runoff controls are available to address stormwater
that drains off rooftops. The objective is to reduce the total volume and rate of runoff from
individual lots, and retain the pollutants on site that maybe picked up from roofing materials
and atmospheric deposition. Roof runoff controls consist of directing the roof runoff away from
paved areas and mitigating flow to the storm drain system through one of several general
approaches: cisterns or rain barrels; dry wells or infiltration trenches; pop-up emitters, and
foundation planting. I9re first three approaches require the roof runoff to be contained in a
gutter and downspout system. Foundation planting provides a vegetated strip wider the drip
line of the roof.
Approach
Design of individual lots for single -family homes as well as lots for higher density residential and
commercial structures should consider site design provisions for containing and infiltrating roof
runoff or directing roof runoff to vegetative swales or buffer areas. Retained water can be reused
for watering gardens, lawns, and trees. Benefits to the environment include reduced demand for
potable water used for irrigation, improved stormwater quality, increased groundwater
recharge, decreased runoff volume and peak flows, and decreased flooding potential.
Suitable Applications
Appropriate applications include residential, commercial and industrial areas planned for
development or redevelopment.
Design Considerations
Designing New Installations
Cisterns or Rain Barrels
One method of addressing roof runoff is to direct roof downspouts
to cisterns or rain barrels. A cistern is an above ground storage
vessel with either a manually operated valve or a permanently
open outlet. Roof runoff is temporarily stored and then released
for irrigation or infiltration between storms. The number of rain
January 2003 Califomla Stormwater BMP Handbook 1 of 3
New Development and Redevelopment
www.cabmphandbook.com
SD -11 Roof Runoff Controls
barrels needed is a function of the rooftop area. Some low impact developers recommend that
every house have at least 2 rain barrels, with a minimum storage capacity of r000 liters. Roof
barrels serve several purposes including mitigating the fust flush from the roof which has a high
volume, amount of contaminants, and thermal load. Several types of rain barrels are
commercially available. Consideration must be given to selecting rain barrels that are vector
proof and childproof. In addition, some barrels are designed with a bypass valve that filters out
grit and other contaminants and routes overflow to a soak -away pit or rain garden.
If the cistern has an operable valve, the valve can be closed to store stormwater for irrigation or
infiltration between storms. This system requires continual monitoring by the resident or
grounds crews, but provides greater flexibility in water storage and metering. If a cistern is
provided with an operable valve and water is stored inside for long periods, the cistern must be
covered to prevent mosquitoes from breeding.
A cistern system with a permanently open outlet can also provide for metering stormwater
runoff. If the cistern outlet is significantly smaller than the size of the downspout inlet (say 114 to
1/2 inch diameter), runoff will build up inside the cistern during storms, and will empty out
slowly after peak intensities subside. This is a feasible way to mitigate the peak flow increases
caused by rooftop impervious land coverage, especially for the frequent, small storms.
Dry wells and Infiltration Trenches
Roof downspouts can be directed to dry wells or infiltration trenches. A dry wwell is constructed
by excavating a hole in the ground and filling it with an open graded aggregate, and allowing the
water to fill the dry well and infiltrate after the storm event. An underground connection from
the downspout conveys water into the dry well, allowing it to be stored in the voids. To
minimize sedimentation from lateral soil movement, the sides and top of the stone storage
matrix can be wrapped in a permeable filter fabric, though the bottom may remain open. A
perforated observation pipe can be inserted vertically into the dry well to allow for inspection
and maintenance.
In practice, dry wells receiving runoff from single roof downspouts have been successful over
long periods because they contain very little sediment. They must be sized according to the
amount of rooftop runoff received, but are typically 4 to 5 feet square, and 2 to 3 feet deep, with
a minimum of r -foot soil cover over the top (maJdmmu depth of ro feet).
To protect the foundation, dry wells must be set away front the building at least io feet. They
must be installed in solids that accommodate infiltration. In poorly drained soils, drywells have
very limited feasibility.
Infiltration trenches function in a similar manner and would be particularly effective for larger
roof areas. An infiltration trench is a long, narrow, rock -filled trench with no outlet that receives
stormwater runoff. These are described under Treatment Controls.
Pop -tip Drainage Emitter
Roof downspouts can be directed to an underground pipe that daylights some distance from the
building foundation, releasing the roof runoff through a pop -up emitter. Similar to a pop -up
irrigation head, the emitter only opens when there is flow from the roof. The emitter remains
flush to the ground during dry periods, for ease of lawn or landscape maintenance.
2 of 3 California Stormwater BMP Handbook January 2003
New Development and Redevelopment
www.cabmphandbook.com
Roof Runoff Controls
SD -11
Foundation Planting
Landscape planting can be provided around the base to allow increased opportunities for_
stornnvater infiltration and protect the soil from erosion caused by concentrated sheet flow
coming off the roof. Foundation plantings can reduce the physical impact of water on the soil
and provide a subsurface matrix of roots that encourage infiltration. These plantings must be
sturdy enough to tolerate the heavy runoff sheet flows, and periodic soil saturation.
Redeveloping Existing Installations
Various jurisdictional stormwater management and mitigation plans (SUSMP, WQMP, etc.)
define "redevelopment" in terms of amounts of additional impervious area, increases in gross
floor area and /or exterior construction, and land disturbing activities with structural or
impervious surfaces. The definition of" redevelopment" nmst be consulted to determine
whether or not the requirements for new development apply to areas intended for
redevelopment. If the definition applies, the steps outlined under `designing new installations"
above should be followed.
Supplemental Information
Examples
■ City of Ottawa's Water Links Surface —Water Quality Protection Program
■ City of Toronto Downspout Disconnection Program
■ City of Boston, MA, Rain Barrel Demonstration Program
Other Resources
Hager, Marty Catherine, Stormwater, "Low- Impact Development ", January /February 2003.
wwwstornlh2o.conr
Low Impact Urban Design Tools, Low Impact Development Design Center, Beltsville, MD.
www.lid- stormwater.net
Start at the Source, Bay Area Stormwater Management Agencies Association, iggg Edition
January 2003 California Stormwater BI4P Handbook 3 of 3
New Development and Redevelopment
www.cabmphandbook.com
Efficient Irrigation SD -12
Design Objectives
p Maximize Infiltration
p Provide Retention
p Slow Runoff
Minimize Impervious Land
Coverage
Prohibit Dumping of Improper
Materials
Contain Pollutants
Collect and Convey
Description
Irrigation water provided to landscaped areas may result in excess irrigation water being
conveyed into storrnwater drainage systems.
Approach
Project plan designs for development and redevelopment should include application methods of
irrigation water that minimize runoff of excess irrigation water into the stormwater conveyance
system.
Suitable Applications
Appropriate applications include residential, commercial and industrial areas planned for
development or redevelopment. (Detached residential single - family homes are typically
excluded from this requirement.)
Design Considerations
Designing New Installations
Ilie following methods to reduce excessive irrigation runoff should be considered, and
incorporated and implemented where determined applicable and feasible by the Permittee:
• Employ rain - triggered shutoff devices to prevent irrigation after precipitation.
• Design irrigation systems to each landscape area's specific water requirements.
• Include design featuring flow reducers or shutoff valves
triggered by a pressure drop to control water loss in the event
of broken sprinkler heads or lines.
• Implement landscape plans consistent with County or City
water conservation resolutions, which may include provision
of water sensors, programmable irrigation times (for short
cycles), etc.
in ^ra- 1nx.aienm
January 2003 California Stormwater BMP Handbook 1 of 2
New Development and Redevelopment
www.cabmphandbooks.com
SD -12 Efficient Irrigation
■ Design timing and application methods of irrigation water to minimize the runoff of excess
irrigation water into the storm water drainage system.
■ Group plants with similar water requirements in order to reduce excess irrigation runoff and
promote surface filtration. Choose plants with low irrigation requirements (for example,
native or drought tolerant species). Consider design features such as:
Using mulches (such as wood chips or bar) in planter areas without ground cover to
minimize sediment in runoff
Installing appropriate plant materials for the location, in accordance with amount of
sunlight and climate, and use native plant materials where possible and /or as
recommended by the landscape architect
Leaving a vegetative barrier along the property boundary and interior watercourses, to
act as a pollutant filter, where appropriate and feasible
- Choosing plants that minimize or eliminate the use of fertilizer or pesticides to sustain
growth
■ Employ other comparable, equally effective methods to reduce irrigation water runoff.
Redeveloping Existing Installations
Various jurisdictional storrunvater management and mitigation plans (SUSMP, WQMP, etc.)
define "redevelopment" in terms of amounts of additional impervious area, increases in gross
floor area and /or exterior construction, and land disturbing activities with structural or
impervious surfaces. The definition of " redevelopment" must be consulted to deterv» ne
whether or not the requirements for new development apply to areas intended for
redevelopment. If the definition applies, the steps outlined under "designing new installations"
above should be followed.
Other Resources
A Manual for the Standard Urban Stormwater Mitigation Plan (SUSMP), Los Angeles County
Department of Public Works, May 2002.
Model Standard Urban Stoma Water Mitigation Plan (SUSMP) for San Diego County, Port of
San Diego, and Cities in San Diego County, February 14, 2002.
Model Water Quality Management Plan (WQMP) for County of Orange, Orange County Flood
Control District, and the hncorporated Cities of Orange County, Draft February 2003.
Ventura Countywide Technical Guidance Manual for Stormwater Quality Control Measures,
July 2002.
2 of 2 California Stormwater BMP Handbook January 2003
New Development and Redevelopment
www.cabmphandbooks.com
Storm Drain Signage
SD -13
Design Objectives
Maximize Infiltration
Provide Retention
Slow Runoff
Minimize Impervious Land
Coverage
0 Prohibit Dumping of Improper
Materials
Contain Pollutants
Collect and Convey
Description
Waste - materials dumped into storm drain inlets can have severe impacts on receiving and
ground waters. Posting notices regarding discharge prohibitions at storm drain inlets can
prevent waste dumping. Storm drain signs and stencils are highly visible source controls that
are typically placed directly adjacent to storm drain inlets.
Approach
The stencil or affixed sign contains a brief statement that prohibits dumping of improper
materials into the urban runoff conveyance system. Storm drain messages have become a
popular method of alerting the public about the effects of and the prohibitions against waste
disposal.
Suitable Applications
Stencils and signs alert the public to the destination of pollutants discharged to the storm drain.
Signs are appropriate in residential, commercial, and industrial areas, as well as any other area
where contributions or dumping to storm drains is likely.
Design Considerations
Storm drain message markers or placards are recommended at all storm drain inlets within the
boundary of a development project. The marker should be placed in clear sight facing toward
anyone approaching the inlet fivm either side. All storm drain inlet locations should be
identified on the development site map.
Designing New Installations
The following methods should be considered for inclusion in the
project design and show on project plans:
■ Provide stenciling or labeling of all storm drain inlets and
catch basins, constructed or modified, within the project area
with prohibitive language. Examples include "NO DUMPING
lanuary 2003 California Stormwater BrdP Handbook 1 of 2
New Development and Redevelopment
www.cabmphandbooks.com
SD -13 Storm Drain Signage
— DRAINS TO OCEAN" and /or other graphical icons to discourage illegal dumping
■ Post signs with prohibitive language and /or graphical icons, which prohibit illegal dumping
at public access points along channels and creeks within the project area.
Note - Some local agencies have approved specific signage and /or storm drain message placards
for use. Consult local agency stormwater staff to determine specific requirements for placard
types and methods of application.
Redeveloping Existing Installations
Various jurisdictional stornnvater management and mitigation plans (SUSMP, WQMP, etc.)
define "redevelopment' in terms of amounts of additional impervious area, increases in gross
floor area and /or exterior construction, and land disturbing activities with structural or
impervious surfaces. If the project meets the definition of "redevelopment', then the
requirements stated under " designing new installations" above should be included in all project
design plans.
Additional Information
Maintenance Considerations
■ Legibility of markers and signs should be maintained. If required by the agency with
jurisdiction over the project, the owner /operator or homeommer's association should enter
into a maintenance agreement with the agency or record a deed restriction upon the
property title to maintain the legibility of placards or signs.
Placement
• Signage on top of curbs tends to weather and fade.
• Signage on face of curbs tends to be worn by contact with vehicle tires and sweeper brooms.
Supplemental Information
Examples
■ Most MS4 programs have storm drain signage programs. Some MS4 programs will provide
stencils, or arrange for volunteers to stencil stornn drains as part of their outreach program.
Other Resources
A Manual for the Standard Urban Stornnvater Mitigation Plan (SUSMP), Los Angeles County
Department of Public Works, May 2002.
Model Standard Urban Storm Water Mitigation Plan (SUSMP) for San Diego County, Port of
San Diego, and Cities in San Diego County, February 14, 2002.
Model Water Quality Management Plan (WQMP) for County of Orange, Orange County Flood
Control District, and the Incorporated Cities of Orange County, Draft February 2003.
Ventura Countywide Technical Guidance Manual for Stormwater Quality Control Measures,
July 2002.
2 of 2 Callfornla Stormwater BNP Handbook January 2003
New Development and Redevelopment
www.cabmphandbooks.com
Trash Storage Areas SD -32
Description
Trash storage areas are areas where a trash receptacle (s) are
located for use as a repository for solid wastes. Stormwater
runoff from areas where trash is stored or disposed of can be
polluted. In addition, loose trash and debris can be easily
transported by water or wind into nearby storm drain inlets,
channels, and /or creeks. Waste handling operations that may be
sources of stormwater pollution include dumpsters, litter control,
and waste piles.
Approach
This fact sheet contains details on the specific measures required
to prevent or reduce pollutants in stormwater runoff associated
with trash storage and handling. Preventative measures
including enclosures, containment structures, and impervious
pavements to mitigate spills, should be used to reduce the
likelihood of contamination.
Suitable Applications
Design Objectives
Maximize Infiltration
Provide Retention
Slow Runoff
Minimize Impervious Land
Coverage
Prohibit Dumping of Improper
Materials
0 Contain Pollutants
Collect and Convey
Appropriate applications include residential, commercial and industrial areas planned for
development or redevelopment. (Detached residential single - family homes are typically
excluded from this requirement.)
Design Considerations
Design requirements for waste handling areas are governed by Building and Fire Codes, and by
current local agency ordinances and zoning requirements. The design criteria described in this
fact sheet are meant to enhance and be consistent with these code and ordinance requirements.
Hazardous waste should be handled in accordance with legal requirements established in Title
22, California Code of Regulation.
Wastes from commercial and industrial sites are typically hauled by either public or commercial
carriers that may have design or access requirements for waste storage areas. The design
criteria in this fact sheet are recommendations and are not intended to be in conflict with
requirements established by the waste hauler. The waste hauler should be contacted prior to the
design of your site trash collection areas. Conflicts or issues should be discussed with the local
agency.
Designing New Installations
Trash storage areas should be designed to consider the following structural or treatment control
BMPs:
■ Design trash container areas so that drainage from adjoining
roofs and pavement is diverted around the area(s) to avoid
run -on. This might include berming or grading the waste
handling area to prevent run-on of stormwater.
■ Make sure trash container areas are screened or walled to
prevent off -site transport of trash.
c � � ❑nn Cl � vrnnncaiTx
January 2003 Callfornia Stonnwater BIdP Handbook 1 of 2
New Development and Redevelopment
www.cabmphandbooks.com
SD -32 Trash Storage Areas
■ Use lined bins or dumpsters to reduce leaking of liquid waste.
• Provide roofs, awnings, or attached lids on all trash containers to minimize direct
precipitation and prevent rainfall from entering containers.
• Pave trash storage areas with an impervious surface to mitigate spills.
• Do not locate storm drains in immediate vicinity of the trash storage area.
• Post signs on all dumpsters informing users that hazardous materials are not to be disposed
of therein.
Redeveloping Existing Installations
Various jurisdictional stormwater management and mitigation plans (SUSMP, WQMP, etc.)
define "redevelopment" in terms of amounts of additional impervious area, increases in gross
floor area and /or exterior construction, and land disturbing activities with structural or
impervious surfaces. The definition of " redevelopment" must be consulted to determine
whether or not the requirements for new development apply to areas intended for
redevelopment. If the definition applies, the steps outlined under "designing new installations"
above should be followed.
Additional Information
Maintenance Considerations
The integrity of structural elements that are subject to damage (i.e., screens, covers, and signs)
must be maintained by the owner /operator. Maintenance agreements between the local agency
and the owner /operator may be required. Some agencies will require maintenance deed
restrictions to be recorded of the property title. If required by the local agency, maintenance
agreements or deed restrictions must be executed by the owner /operator before improvement
plans are approved.
Other Resources
A Manual for the Standard Urban Stormwater Mitigation Plan (SUSMP), Los Angeles County
Department of Public Works, May 2002.
Model Standard Urban Storm Water Mitigation Plan (SUSMP) for San Diego County, Port of
San Diego, and Cities in San Diego County, February 34, 2002.
Model Water Quality Management Plan (WQMP) for County of Orange, Orange County Flood
Control District, and the Incorporated Cities of Orange County, Draft February 2003.
Ventura Countywide Technical Guidance Manual for Stormwater Quality Control Measures,
July 2002.
2 of 2 California Stormwater BMP Handbook January 2003
New Development and Redevelopment
www.cabrnphandbooks.com